• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.190-190
• /
• 2009

전자산업에의 필수인 커패시터는 소형화, 저저항, 고전압을 향한 추세가 늘고 있으며, 이외에도 고전압 전원, 고전압 회로 등 중전기기에 필요한 고전압, 고용량 커패시터가 사용되고 있다. 중전기기에 사용되는 커패시터는 기기에 따라 틀리지만 내전압이 보통 10kV 이상이고 정전용량이 500pF 안팎이며, 대부분 외국에서 수입에 의존하고 있는 실정이다. 본 연구에서는 $Nb_2O_5$를 2mol% 첨가한 $BaTiO_3$를 일반적인 고상 소결법으로 제조하고 성형 시 crack을 방지하기 위해 binder 및 plasticizer를 사용하였으며, binder 첨가량에 따른 성형밀도를 측정하여 최적의 binder양을 선택하였다. 성형 밀도가 떨어짐에 따라 절연파괴강도가 낮아지기 때문에 성형 밀도를 높이기 위해 CIP를 하였으며, 소결후 capacitance와 d-factor를 측정하여 수치가 허용 범위에 들어 올 경우 전극을 형성하고 표면파괴를 방지하기 위하여 epoxy로 표면코팅을 하였다. DC 60kV용 Hi-pot tester를 사용하여 15kV까지 선형적으로 증가시켜 내전압 테스트를 실시하였으며, 제조 된 커패시터 중 몇 개의 sample을 SEM 및 XRD를 사용하여 미세구조와 결정상을 조사하였다.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.14 no.1
• /
• pp.67-74
• /
• 2000

This paper presents the analysis of partial discharge signals according to the particle states in GIS, for preventing the insulation failure and recognizing the particle states. In this paper, four states of particle (particle on electrode, particle on enclosure, particle on spacer and crossing particle) were simulated. And $\Phi$-Q-N distribution of partial discharge signals was analyzed and the statistical operator of the $\Phi$-Q distribution was analyzed. As a result, it was found that the states of particle were distinguished by analysis of the $\Phi$-Q-N distribution and the statistical operator of the $\Phi$-Q distribution.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.7
• /
• pp.2298-2314
• /
• 1996

Electric field effect on boiling of refrigerants R11, R113, and FC72 has been investigated experimentally. One purpose of the experimental investigation is to determine the effects of the electrode arrangements on electrohydrodynamic boiling of the above mentioned liquids. The test equipment employed in the experiment consists of a shell and tube heat exchanger with six or six and twelve rows of electrode wires around the tube. It has been found that the applied voltage promotes the boiling heat transfer coefficient except FC72. Boiling heat transfer enhancement obtained is about 230% for R11, 280% for R113. It has also been observed that bubbles detached from the tube aggregate at the place where the electrical gradient force balances with the buoyancy one. These aggregated bubbles force to decrease the boiling heat transfer coefficient as well as to reduce the voltage needed to the dielectric breakdown.

• Journal of the Korean Vacuum Society
• /
• v.10 no.4
• /
• pp.440-448
• /
• 2001

The operation properties of DBD plasma reactors were observed by using 20 kV square pulse at the cylindrical and planar type of reactors in the condition of air pressure. The optimum operation frequency $f_0$ which optimizes the efficiency of operation was found as such $f_0\proptoexp(-C)$ when the current-voltage curve and charge-voltage curve were observed. Using these properties the dissipated power was evaluated. The dissipated power at the optimum frequency of operation was varied as the value of capacitance which is dependent on the structure and the dielectric material of the reactor, and had the maximum value at the specific value of capacitance. With these value of capacitance, DBD reactors which has a high level of efficiency can be formed.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.10a
• /
• pp.34.2-34.2
• /
• 2011

본 연구에서는 1986년에 국내 섬 지역에 설치된 태양전지 모듈을 대상으로 전기적 특성값의 열화 및 열화 원인에 대한 분석을 실시하였다. 태양전지 모듈의 초기 최대 출력값은 50 W였고, 5인치 단결정 실리콘 태양전지 36개로 구성되어 있었다. 첫째로, 육안 검사를 통해서 태양전지 모듈의 열화 현상을 관찰하였다. 태양전지 모듈의 절연성은 IEC 61215의 기준으로 측정하였다. 태양전지 모듈의 전기적 특성평가를 통해서 최대 출력값의 변화량을 측정하였고, EL(Electroluminescence) 측정을 통해서 태양전지의 열화를 분석하였다. 이를 통해 분석된 주요 열화 모드는 봉지재 (Encapsulant)의 변색(Discoloration) 및 박리(Delamination)현상이었다. 봉지재의 변색된 부분 및 변색되지 않은 부분의 태양광 반사도를 측정한 결과 변색된 부위의 반사도가 증가한 것을 확인하였다. 두번째로 최대 출력전압을 태양전지 모듈에 인가한 상태에서 태양전지 각각의 온도를 T.C (Thermocouple)을 이용하여 측정하였고, 이를 통해서 태양전지의 열화와 온도와의 관계를 분석하였다. 마지막으로 태양전지 모듈의 단면분석을 통해서 봉지재의 박리현상 및 리본와이어의 솔더 접합계면을 관찰하였다. 또한, 봉지재를 제거한 후에 SEM&EDX를 통해서 리본와이어 및 금속전극의 부식현상을 분석하였다.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.16 no.1
• /
• pp.8-12
• /
• 2002

In this paper, we studied a flat fluorescent lamp with high luminance for LCD backlighting. The lamps have simple structures with ITO glass, insulator layer, phosphor layer, electrode layer and gas gap. The firing voltage was decreased with increasing the frequency. It was considered that this tendency was resulted from the space charge effect due to Xe and Ar positive ions trapped in gas gap. Decrease of uniform voltage at higher drive frequency is due to the remaining space charges which are produced by preceding period. As a result, luminance of 2700[cd/m$^2$] and maximum luminous efficiency of 51[m/W] were obtained with luminance uniformity of 96[%] in operation(700[V$\_$rms/], 80[kHz].

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.12
• /
• pp.1118-1123
• /
• 2008

High voltage multilayer ceramic capacitors (MLCCs) are classified into two classes-those for temperature compensation (class I) and high dielectric constant materials (class II). We manufactured high voltage MLCC with temperature coefficient characteristics of C0G and X7R and studied the characteristics of electric properties. Also we studied the characteristics of dielectric breakdown voltage (V) as the variation of thickness in the green sheet and how to pattern the internal electrodes. The dielectric breakdown by electric field was caused by defects in the dielectric materials and dielectric/electrode interface, so the dielectric thickness increased, the withstanding voltage per unit (E) thickness decreased. To overcome this problem, we selected the special design like as floating electrode and this design affected the increasing breakdown voltage(V) and realized the constant withstanding voltage per unit thickness(E). From these results, high voltage application of MLCCs can be expanded and the rated voltage can also be develop.

• Journal of Korean Society for Atmospheric Environment
• /
• v.28 no.6
• /
• pp.675-687
• /
• 2012

Applying an external electric field across air filter media is one of methods to improve the filtration performance. Metal wire meshes have been commonly used as electrodes situated on both sides of a thick filter pad. For a thin filter medium a short circuit, known as the biggest drawback for applying an external electric field to air filter, can occur at the closest point between electrodes. In this study several types of insulated meshes were prepared by coating #50 meshes with a dielectric material, Nylon 66, and the filtration property of air filter was evaluated at the presence of external electric field using those insulated meshes as electrodes and compared with that of filters using bared meshes. The collection efficiency of tested filter was increased from 78% to 95% for singly charged 100 nm particles by application of external electric field. As a result, there was no significant difference in collection efficiency between filters with insulated and bared electrodes. Similar results could be also seen from the tests using polydisperse particles. Finally, through this study, we found that the insulation of mesh electrodes doesn't affect the filtration performance of fibrous air filter under external electric field.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.162-163
• /
• 2006

XLPE is used to insulator for Ultra High Voltage power cable. It is easy to processing also has a good insulating property. The study for diagnosis of lifetime and improvement is proceeding continuously. In this paper, it is investigated partial discharge distribution according to slope of needle electrode 0, 20, $40^{\circ}$. Applied voltage is 0.5 [kV/s] by step form for inception voltage. As the result of study, we conformed that increase of slope led to reduce of discharge number and total discharge quantity.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2000.05a
• /
• pp.493-496
• /
• 2000

This study is about the design and fabrication of optical voltage sensor modules improved in the insulation reliability, where we adopted the space-division voltage system using the auxiliary electrodes to apply the uniform electric fields to the BSO, the device of which the polarization state varies with the variation of refractive index in the electric fields. We measured the output of fiber-Optic Voltage Sensors with the temperature changes in the thermostatic oven. And we measured the output of Fiber-Optic Voltage Sensors after setting its up in the disttibuion automated switch being apply 60Hz alternating voltage from 6.6kV to 17.BkV. In result, measured error characteristic is good, so we can judge it is applicable to the practical case