• Korean Chemical Engineering Research
• /
• v.44 no.2
• /
• pp.179-186
• /
• 2006

Two types of $TiO_2$, nanotube and nanoparticle, were used for the mesoporous coatings by doctor blade technique followed by calcining at $450^{\circ}C$. The coatings were used as working materials for dye-sensitized solar cells (DSCs) later on and their photovoltaic characterization was carried out. The nanoparticle was synthesized from hydrogen titanate nanotube by hydrothermal treatment at $180^{\circ}C$ for 24 hr. The solar energy conversion efficiency (${\eta}$) of DSCs prepared by this nanoparticle reached 8.07％ with $V_{OC}$ (open-circuit potential) of 0.81 V, $I_{SC}$ (short-circuit current) of $18.29mV/cm^2$, and FF (fill factor) of 66.95％, respectively. For the preparation of nanotube, the concentration of NaOH solution varied from 3 M to 5 M. In the case of DSCs fabricated with nanotubes from 3 M NaOH solution, the ${\eta}$ reached 6.19％ with $V_{OC}$ of 0.77 V, $I_{SC}$ of $12.41mV/cm^2$, and FF of 64.49％, respectively. On the other hand, in the case of 5 M solution, the photovoltaic ${\eta}$ was decreased with 4.09％ due to a loss of photocarriers. In conclusion, it is demonstrated that the solar energy conversion efficiency of DSCs made from $TiO_2$ nanoparticle showed best results among those under investigation.

• Journal of the Korean Vacuum Society
• /
• v.17 no.4
• /
• pp.322-330
• /
• 2008

The properties of discharge, luminance, and spectroscopy are investigated in a longitudinal and transverse discharge fluorescent lamps with tube of outer diameter 4 mm. The sample lamps are prepared to be three kinds of gas composition such as mercury lamps of Ne(95%)+Ar(5%)+Hg(2 mg), the mercury-free lamps of Xe 100% and Ne+Xe(4%). The gas pressure is in the range of $5{\sim}300\;Torr$. In the mercury lamps, the longitudinal discharge having a positive column is high in luminance and efficiency, while the transverse discharge is no luminance at all. In the Xe-lamps, the transverse discharge shows relatively good in efficiency as compared with the longitudinal discharge which has a high discharge voltage and a low luminance and efficiency. In the transverse discharge of relatively high efficiency, a pure Xe(100%) gas discharge has a higher efficiency than the mixture gas of Ne+Xe(4%). Through these experiments, the properties of mercury and xenon lamps are verified. In the mercury lamps, the longitudinal discharge of tubular fluorescent lamps is high in luminance and efficiency, while the transverse discharge of flat panel fluorescent lamps are low in luminance efficiency. In the mercury-free lamps, the flat fluorescent lamps of transverse discharge having a high pressure ${\sim}100\;Torr$ with the pure Xe-gas are verified to be suggestable.

• The KIPS Transactions:PartD
• /
• v.13D no.7 s.110
• /
• pp.985-996
• /
• 2006

As the internet technologies develop, the geographic information system environment is changing to the web-based service. Since geospatial information of the existing Web-GIS services were developed independently, there is no interoperability to support diverse map formats. In spite of the same geospatial information object it can be used for various proposes that is duplicated in GIS separately. It needs intelligent strategies for optimal replica selection, which is identification of replication geospatial information objects. And for management of replication objects, OMG, GLOBE and GRID computing suggested related frameworks. But these researches are not thorough going enough in case of geospatial information object. This paper presents a model of location service, which is supported for optimal selection among replication and management of replication objects. It is consist of tree main services. The first is binding service which can save names and properties of object defined by users according to service offers and enable clients to search them on the service of offers. The second is location service which can manage location information with contact records. And obtains performance information by the Load Sharing Facility on system independently with contact address. The third is intelligent selection service which can obtain basic/performance information from the binding service/location service and provide both faster access and better performance characteristics by rules as intelligent model based on rough sets. For the validity of location service model, this research presents the processes of location service execution with Graphic User Interface.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.15 no.6
• /
• pp.252-259
• /
• 2005

Single crystal $CuGaSe_2$ layers were grown on thoroughly etched semi-insulating CaAs(100) substrate at $450^{\circ}C$ with hot wall epitaxy (HWE) system by evaporating $CuGaSe_2$ source at $610^{\circ}C$. The crystalline structure of the single crystal thin films was investigated by the photoluminescence (PL) and double crystal X-ray diffraction (DCXD). The carrier density and mobility of single crystal $CuGaSe_2$ thin films measured with Hall effect by Van der Pauw method are $4.87{\times}10^{17}cm^{-3}$ and $129cm^2/V{\cdot}s$ at 293 K, respectively. The temperature dependence of the energy band gap of the $CuGaSe_2$ obtained from the absorption spectra was well described by the Varshni's relation, $E_g(T)=1.7998eV-(8.7489{\times}10^{-4}eV/K)T^2/(T+335K)$. The voltage, current density of maxiumun power, fill factor, and conversion, efficiency of $n-CdS/p-CuGaSe_2$, heterojunction solar cells under $80mW/cm^2$ illumination were found to be 0.41 V, $21.8mA/cm^2$, 0.75 and 11.17%, respectively.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.4
• /
• pp.423-428
• /
• 2010

Electrostatic precipitators (ESPs) used currently in industries for removing fine particles from semiconductors have to be made of expensive anticorrosive metallic materials in order to maintain their particle-removal performance. To satisfy the economical demands of industries, a novel ESP was developed; in this ESP, the charger is made of carbon fibers and collection plates consist of PET films among which an aluminum sheet is inserted. The ESP was evaluated by changing the voltages applied to the chargers and collection plates, flow rates, and number of charging channels. KCl particles with mean diameters of 100 nm were used, and a scanning mobility particle sizer was used to measure the changes in particle number concentrations upstream and downstream of the ESP. The experimental results showed that more than 90% of the particles were removed by using the ESP containing ionizers with nine channels and 65-mm collection plates at $500\;m^3/hr$ when voltages of 7 kV and 10 kV were applied to the ionizers and collection plates, respectively.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.1
• /
• pp.71-78
• /
• 2020

In the case of power generation using renewable energy, power production may not be smooth due to the influence of the weather. The energy storage system (ESS) is used to increase the efficiency of solar and wind power generation. ESS has been continuously fired due to a lack of battery protection systems, operation management, and control system, or careless installation, leading to very big casualties and economic losses. ESS stability and battery protection system operation management technology is indispensable. In this paper, we present a battery level calculation algorithm and a failure prediction algorithm for ESS optimization and stable operation. The proposed algorithm calculates the correct battery level by accumulating the current amount in real-time when the battery is charged and discharged, and calculates the battery failure by using the voltage imbalance between battery cells. The proposed algorithms can predict the exact battery level and failure required to operate the ESS optimally. Therefore, accurate status information on ESS battery can be measured and reliably monitored to prevent large accidents.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.261-261
• /
• 2016

플래시 메모리 (flash memory)는 DRAM(dynamic racdom access memory)이나 SRAM(static random access memory)에 비해 소자의 구조가 매우 단순하기 때문에 집적도가 높아서 기기의 소형화가 가능하다는 점과 제조비용이 낮다는 장점을 가지고 있다. 또한, 전원을 차단하면 정보가 사라지는 DRAM이나 SRAM과 달리 전원이 꺼지더라도 저장된 정보가 지워지지 않는다는 특징을 가지고 있어서 ROM(read only memory)과 정보의 입출력이 자유로운 RAM의 장점을 동시에 가지기 때문에 활용도가 크다. 또한, 속도가 빠르고 소비전력이 작아서 USB 드라이브, 디지털 TV, 디지털 캠코더, 디지털 카메라, 휴대전화, 개인용 휴대단말기, 게임기 및 MP3 플레이어 등에 널리 사용되고 있다. 특히, 낸드(NAND)형의 플래시 메모리는 고집적이 가능하며 하드디스크를 대체할 수 있어 고집적 음성이나 화상 등의 저장용으로 많이 쓰이며 일정량의 정보를 저장해두고 작업해야 하는 휴대형 기기에도 적합하며 가격도 노어(NOR)형에 비해 저렴하다는 장점을 가진다. 최근에는 smart watch, wearable device 등과 같은 차세대 디스플레이 소자에 대한 관심이 증가함에 따라 투명하고 유연한 메모리 소자에 대한 연구가 다양하게 진행되고 있으며 유리나 플라스틱과 같은 기판 위에서 투명한 플래시 메모리를 형성하는 기술에 대한 관심이 높아지고 있다. 전하트랩형 (charge trap type) 플래시 메모리는 플로팅 게이트형 플래시 메모리와는 다르게 정보를 절연막 층에 저장하므로 인접 셀간의 간섭이나 소자의 크기를 줄일 수 있기 때문에 투명하고 유연한 메모리 소자에 적용이 가능한 차세대 플래시 메모리로 기대되고 있다. 전하트랩형 플래시메모리는 정보를 저장하기 위하여 tunneling layer, trap layer, blocking layer의 3층으로 이루어진 게이트 절연막을 가진다. 전하트랩 플래시 메모리는 게이트 전압에 따라서 채널의 전자가 tunnel layer를 통해 trap layer에 주입되어 정보를 기억하게 되는데, trap layer에 주입된 전자가 다시 채널로 빠져나가는 charge loss 현상이 큰 문제점으로 지적된다. 따라서 tunnel layer의 막질향상을 위한 다양한 열처리 방법들이 제시되고 있으며, 기존의 CTA (conventional thermal annealing) 방식은 상대적으로 높은 온도와 긴 열처리 시간을 가지고, RTA (rapid thermal annealing) 방식은 매우 높은 열처리 온도를 필요로 하기 때문에 플라스틱, 유리와 같은 다양한 기판에 적용이 어렵다. 따라서 본 연구에서는 기존의 열처리 방식보다 에너지 전달 효율이 높고, 저온공정 및 열처리 시간을 단축시킬 수 있는 마이크로웨이브 열처리(microwave irradiation, MWI)를 도입하였다. Tunneling layer, trap layer, blocking layer를 가지는 MOS capacitor 구조의 전하트랩형 플래시 메모리를 제작하여 CTA, RTA, MWI 처리를 실시한 다음, 전기적 특성을 평가하였다. 그 결과, 마이크로웨이브 열처리를 실시한 메모리 소자는 CTA 처리한 소자와 거의 동등한 정도의 우수한 전기적인 특성을 나타내는 것을 확인하였다. 따라서, MWI를 이용하면 tunnel layer의 막질을 향상시킬 뿐만 아니라, thermal budget을 크게 줄일 수 있어 차세대 투명하고 유연한 메모리 소자 제작에 큰 기여를 할 것으로 예상한다.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.5
• /
• pp.750-759
• /
• 2016

The $MnO_2$ electrodeposited on the surface of the carbon nanofiber mats ($MnO_2$-LCNFM) were prepared from electrospun lignin-g-PAN copolymer via heat treatments and subsequent $MnO_2$ electrodeposition method. The resulting $MnO_2$-LCNFM was evaluateed for its potential use in a supercapicitor electrode. The increase of $MnO_2$ electric deposition time was revealed to increase diameter of carbon nanofibers as well as $MnO_2$ content on the surface of carbon nanofiber mats as confirmed by scanning electon microscope (SEM) analysis. The electrochemical properties of $MnO_2$-LCNFM electrodes are evaluated through cyclic voltammetry test. It was shown that $MnO_2$-LCNFM electrode exhibited good electrochemical performance with specific capacitance of $168.0mF{\cdot}cm^{-2}$. The $MnO_2$-LCNFM supercapacitor successfully fabricated using the gel electrolyte ($H_3PO_4$/Polyvinyl alcohol) showed to have the capacitance efficiency of ~90%, and stable behavior during 1,000 charging/discharging cycles.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.12
• /
• pp.8643-8648
• /
• 2015

In this paper presents the design and demonstrate 8 W 3-stage HPA(High Power Amplifier) MMIC(Monolithic Microwave Integrated Circuits) for Ka-band down link satellite communications payload system at 19.5 GHz ~ 22 GHz frequency band. The HPA MMIC consist of 3-stage GaN HEMT(Hight Electron Mobility Transistors). The gate periphery of $1^{st}$ stage, $2^{nd}$ stage and output stage is determined $8{\times}50{\times}2$ um, $8{\times}50{\times}4$ um and $8{\times}50{\times}8$ um, respectively. The fabricated HPA MMIC shows size $3,400{\times}3,200um^2$, small signal gain over 29.6 dB, input matching -8.2 dB, output matching -9.7 dB, output power 39.1 dBm and PAE 25.3 % by using 0.15 um GaN technology at 20 V supply voltage in 19.5~22 GHz frequency band. Therefore, this HPA MMIC is believed to be adaptable Ka-band satellite communication payloads down link system.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.198-198
• /
• 2015

전기변색재료는 전압을 인가하였을 때 전계방향에 따라 가역적으로 색이 변화하는 재료를 말한다. 스마트윈도우용 전기 변색재료는 지속적으로 전기를 가해줄 필요 없이 한번 변색되면 색이 지속되는 특징을 가지므로 에너지 효율적으로 우수하여 태양열 차단 창호나 디스플레이 분야에 응용될 것으로 기대된다. 이러한 전기 변색재료에는 산화형 전기 변색 재료, 환원형 전기 변색 재료가 있는데 이중 가장 널리 연구되고 있는 재료는 환원형 전기변색재료이다. 대표적인 재료로 $WO_3$가 쓰이는 데 이는 전기 변색적 특성이 우수하고 또한 내구성이 다른 재료에 비해 우수하다는 장점 때문이다. 그러나, 상용화를 위해서는 내구성의 개선이 요구되고 있다. 한편, $TiO_2$는 안정성이 매우 뛰어나지만 전기변색적 특성이 $WO_3$에 비해 낮은 점이 지적되고 있다. 이러한 $WO_3$ 및 $TiO_2$ 박막은 스퍼터링 또는 sol-gel법 등으로 제작되고 있는데, 일반적으로 스퍼터링의 경우 치밀한 박막이 형성되기 때문에 Porous 한 박막을 얻기 힘들다. 따라서 본 연구에서는 기판에 입사하는 스퍼터 입자들의 각도를 조절하여 shadowing 효과로 인해 박막의 구조가 porous해지는 Glancing angle deposition을 도입하였다. 이러한 증착법을 이용하여 $WO_3$와 $TiO_2$를 각도를 조절하여 증착하고 $TiO_2$와 $WO_3$ 박막의 특성을 비교하여 본다. 두께 300 nm를 가지는 $WO_3$ 및 $TiO_2$ 박막은 GLAD RF 마그네트론 스퍼터링법을 이용하여 Corning glass(corning E-2000)기판 위에 증착하였다. 기판 입사 각도는 $0^{\circ}$, $30^{\circ}$, $45^{\circ}$, $60^{\circ}$로 증착하였고 직경 3 in의 $TiO_2$, $WO_3$ 타겟을 사용하였다. 또한 스퍼터링 파워는 400 W, 작업압력 1.0 Pa, 그리고 스퍼터링 가스는 O2/Ar+O2 유량 10%에서 30%로 증착을 상온에서 진행하였다. 전기화학적 특성을 평가하기 위하여 $TiO_2$ 및 $WO_3$ 박막을 100 nm 두께의 ITO/glass 위에서 증착하였다. 박막의 미세구조는 XRD와 SEM을 통해 확인하였고, 전기화학적 특성은 Ar 분위기의 Glove box안에서 parstat 2273을 통해 측정하였다. 전해질은 1 M $LiPF_6/PC$로 진행하였고, 대향 전극는 Pt전극을, 참고 전극은 칼로멜 전극을 사용하였다. Potential 범위는 2 V에서 4 V로 진행하였고, scan rate는 50 mV/s로 측정하였다. 투과도는 UV/VIS spectrometer로 측정하였다. 전기변색 특성의 상관관계 및 에 대해서는 학회 당일 발표할 예정이다.