• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.3 no.2
• /
• pp.329-337
• /
• 1999

In this dissertation, the characteristics of W-CDMA(Wideband CDMA) are studied and required specifications of IMT-2000 transceiver using W-CDMA method are proposed. Also, in order to design the RF circuits satisfied the proposed specifications, theoretical models are expanded and real circuits are made. Then the RF circuits of the mobile stations are implemented in the three parts, transmitter, receiver and frequency synthesizer and are evaluated. The frequency synthesizer is designed using techniques of swallow counter and passive 3rd loop filter. For improving characteristics of the loop, a LPF was added to the 2nd loop filter. So although the locking times are loosed, the spurious are reduced. The output power of transmitter is over 50mW, the spurious output is -40dB/30kHz at 5MHz offset and power control range is -20dB at 2.5V. The proposed specifications are considered in highly practical environment and the theoretical designs and the experiments are expressed as simply as possible in order to facilitate understanding. It stands to reason that the results of this study can be used to design the wider CDMA(25MHz Bandwidth) mobile communication systems.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.1
• /
• pp.80-86
• /
• 2010

This paper describes the development result of S-band Transmitter of STSAT-3 by satellite research center(SaTReC), KAIST. STSAT-3 has two kinds of communication channels, S- band for Telemetry & Command and X-band for mission payload. S-band Transmiiter(STX) consist of modulator, frequency synthesizer, power amp and DC/DC converter. The modulation scheme of STX is FSK(Frequency Shift Keying). The interface between spacecraft OBC and STX is RS-422. The STX is based on modular design. The RF output power of STX is 1.5W(31.7dBm) and BER of STX is under 1E-5. The Test of STX is completed successfully such as functional Test and environmental(vibration, thermal vacuum) Test.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.14 no.6
• /
• pp.53-59
• /
• 2010

This research aims in finding a more optimal ejector size for evacuating engine exhaust gasses and 20% of the cell cooling air. The remaining 80% of cell cooling air pumped into the test chamber is separately exhausted from the test chamber via a discharge port fitted with flow control valves and vacuum pump. Unlike its predecessor this configuration utilizes a smaller capture area to improve pressure recovery. The modified ejector size has a diameter of 1100mm enough to evacuate 66kg/s jet engine exhaust in addition to about 20%, 24kg/s of the cell cooling air tapped from the sterling chamber. This configurations has an area ratio of the engine exit and ejector inlet of about 1.2. Simulation results of the proposed ejector configuration, indicates improved pressure recovery.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39A no.3
• /
• pp.161-163
• /
• 2014

We consider the device-to-device (D2D) communication underlaying multi-cell interference system, in which the cellular downlink (DL) resource is reused by K cells and two D2D transmission links within each cell. In this paper, it has been shown that the downlink intra-cell and inter-cell interference can be effectively handled by interference alignment (IA) technique, as long as the simultaneous D2D links are properly selected or power-controlled so that they may not incur interference to the base stations in the same and neighbor cells. In particular, we provides the IA technique that can achieve the theoretically maximum possible degree of freedom (DOF), demonstrating that a total of (K+1)M degrees of freedom (DOFs) can be achieved for K-cell interference system with two underlaying D2D links, where base stations, cellular UE's, and D2D UE's all have M transmit and receive antennas.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.36C no.5
• /
• pp.57-66
• /
• 1999

This paper describes a 12b, 50 Msample/s CMOS AID converter using an acquisition-time minimization technique for the high-speed sampling rate of 50 MHz level. The proposed ADC is implemented in a $0.35\mu\textrm{m}$ double-poly five-metal n-well CMOS technology and adopts a typical multi-step pipelined architecture to optimize sampling rate, resolution, and chip area. The speed limitation of conventional pipelined ADCs comes from the finite bandwidth and resulting speed of residue amplifiers. The proposed acquisition-time minimization technique reduces the acquisition time of residue amplifiers and makes the waveform of amplifier outputs smooth by controlling the operating current of residue amplifiers. The simulated power consumption of the proposed ADC is 197 mW at 3 V with a 50 MHz sampling rate. The chip size including pads is $3.2mm\times3.6mm$.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.8
• /
• pp.9-16
• /
• 2007

Currently, the measurement of RF parameters for a base station in operation is typically limited to easily measured forward path items. In this paper, the forward monitoring ports of base stations are used to measure the reverse RF performance. The system has been implemented and effectiveness has been proven on an operating base station. The receiver sensitivity is measured using an internal CDMA modem which is used to monitor the output power based on closed loop power control when the modem is connected to the base station via a voice call. In order to improve accuracy, in addition to the modem Tx adjust(TxAdj) parameter, the detector's actual measurement is used. For accurate receiver sensitivity, the measurement should be made when there is no traffic which is not possible on an operating base station. Therefore, pilot channel chip energy to received signal power spectral density ratio$(E_c/I_o)$ compensation method is used to offset the receiver sensitivity degradation with voice traffic increase.

• Journal of the Korean Solar Energy Society
• /
• v.34 no.4
• /
• pp.123-129
• /
• 2014

Photovoltaic and fuel cell systems can be used as power source in mobile robots. At this time the photovoltaic system generally generate power in daytime. The starting time of fuel cell is slower than the lithium battery. To compensate for these disadvantages, a battery charge-discharge system is used. Especially the bi-directional converter is used mainly in the charge-discharge method. The controller in a buck converter controls the input voltage of the converter to meet the maximum power point tracking(MPPT) performance. First of all, the simulations of hybrid system for battery charge-discharge system in each step simulated using solar and fuel cell modeling as input source in PSIM. Experiment of the buck and bi-directional converter system is conducted through using photovoltaic/fuel cel simulator(pCube) instead of solar and fuel cell. This hybrid system for battery charge discharge using photovoltaic/fuel cell generates emergency power for the communication system in mobile robot.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.4
• /
• pp.298-308
• /
• 2017

This paper presents a Interleaved Buck Converter(IBC) system with Random PWM to reduce electromagnetic noise by harmonics. Swithced mode power supply generally controlled by high switching frequency have a electromagnetic interference(EMI) issue due to the high-voltage/high-current switching to regulate the voltage in buck converter. To solve the problem. we present a novel IBC system with PRBS. IBC system has two active switches with 180 phase difference that controll the cicuit with two PWM signal. IBC system may be disadventageous for the cost due to the addtion of one set of switch, but it has adventages of power distribution, current ripple cancellation, fast transient response, and passive component size reduction. To verify the validity of study, simulation program has been bulit using PSIM and the experimental results of IBC system using RPWM was compared with the conventinal PWM and randomized PWM.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.10
• /
• pp.1873-1878
• /
• 2017

Recently, many researches have been conducted on the aviation industry to replace the wire harness cable between the avionics of the aircraft with the wireless network. In this paper, we present an Event-Based Simulator for Wireless Avionics Intra-Communications (ES-WAIC) that can verify core technologies of wireless networks and efficiently integrate different layers of the network. ES-WAIC is developed to enhance the readability between the real time control application developers of the higher layer and the network layer developers. Specifically, the practical implement relies on an event-based programming concept to increase portability and compatibility that can be applied to the realistic low-power wireless embedded networks. ES-WAIC implements the overall system layers including the wireless channel modeling of the 4.4GHz band, the physical layer, the medium access control, the network, and the application layer of wireless avionics intra-communications.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.48 no.2
• /
• pp.127-135
• /
• 1999

Multivarialbe Boiler-Turbine H_\infty Control System Genetic Algorithm Weighting Functions $W_1$(s), $W_2$(s), and design parameter $\gamma$ that are given by Glover-Doyle algorithm, to optimally follow the output of reference model. The first method to do this is that the gains of weighting functions $W_1$(s), $W_2$(s), and design parameter are optimized simultaneously by genetic algorithm with the tournament method that can search more diversely, in the search domain which guarantees the robust stability of system. And the second method is that not only by genetic algorithm with the roulette-wheel method that can search more fast, in that search domain. The boiler-turbine H_\infty control system designed by theabove second method has not only the robust stability to a modeling error but also the the better command tracking preformance than those of the H_\infty control system designed by trial-and-error method and the above first method. Also, this boiler-turbine H_\infty control system has the better performance than that of the LQG/LTR contro lsystem. The effectiveness of this boiler-turbineH_\infty control system is verified by computer simulation.