• Journal of IKEEE
• /
• v.19 no.1
• /
• pp.45-51
• /
• 2015

Recently, as WPAN (Wireless Personal Area Network) becomes the necessary feature in IoT (Internet of Things) devices, the importance of data security also hugely increases. In this paper, we present the low-complexity 128-bit AES-$CCM^*$ hardware IP for IEEE 802.15.4 standard. For low-cost and low-power implementation which is essentially required in IoT devices, we propose two optimization methods. First, the folded AES(Advanced Encryption Standard) processing core with 8-bit datapath is presented where composite field arithmetic is adopted for reduced hardware complexity. In addition, to support $CCM^*$ mode defined in IEEE 802.15.4, we propose the mode-toggling architecture which requires less hardware resources and processing time. With the proposed methods, the gate count of the proposed AES-$CCM^*$ IP can be lowered up to 57% compared to the conventional architecture.

• Aerospace Engineering and Technology
• /
• v.12 no.2
• /
• pp.14-23
• /
• 2013

Fault management design of the satellite describes preparations for failures which can occur during operational phase. Fault management design contains detection and isolation function of anomaly, and also it contains function to maintain the satellite in safe condition until the ground station finds out a cause of failure and takes a countermeasure. Unlike normal operation, safing operation is automatically performed by Power Control and Distribution Unit and Integrated Bus Management Unit which loads Flight Software without intervention of ground station. Since fault management operation is automatical, fault management logic and functionality of relevant hardware should be thoroughly checked during ground test phase, and error which is similar to actual should be carefully applied without damage. Verification test for fault management design is conducted for various subsystems of satellite. In this paper, we show the design process of fault management design verification test for Electrical Power Subsystem and Attitude and Orbit Control Subsystem of Low Earth Orbit satellite flight model and the test results.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.1
• /
• pp.136-142
• /
• 2005

In this paper, we wrote about the basic experimentation of Optical CT's temperature characteristic to measure high-current in a super-high-voltage electric power equipment which is using Faraday effect. We used the 1310[nm] Laser Diode as the light source and PIN Photodiode as receiver. For the transmission line of light, we used 30[m] single mode fiber which could maintain the state of polarization in the optical fiber. For the experiment, the temperature transformation device make by aluminium. the The range of current was from 400[A] and 1300[A] and the range of temperature was from $-40[^{\circ}C]\;to\;50[^{\circ}C]$. In a same experimental condition, magnitude increased input current increase follow by increasing proportion of input current.

• Journal of KIISE:Computing Practices and Letters
• /
• v.14 no.4
• /
• pp.436-440
• /
• 2008

In IEEE 802.15.4 beacon-enabled mode, performance decreases as the number of devices competing in the contention access period(CAP) increases. In this letter, we propose partitioned contention access mechanism(PCAM) to compensate performance degradation. In PCAM, the PAN coordinator divides CAP into two sub-periods and activity of devices is delimited in their assigned sub-periods. Since PCAM reduces the number of devices which compete at the same time by half, collision probability between transmitted frames can be reduced. In addition, devices can save their power consumption because PCAM shorten the duration that devices stay in active state into half. We perform simulations to compare the performance of PCAM with that of the IEEE 802.15.4 standard. From the result, PCAM yields better performance than IEEE 802.15.4 standard.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.14 no.5
• /
• pp.27-35
• /
• 2000

This paper deals with a control strategy for constant output power of SSRT(Soft Switching Resonant Type) FB(Full Bridge) DC-DC converter by an improved phase shift controller. When the FB DC-DC converter for the high density and the high effect control is operated in high speed switching, the switching loss and switching stress of the switching devices are increased. So, the soft switching method, which has the phase shift control with the digital I-PD controller, must be use in order to reduce its. And the output voltage that controlled by the digital I-PD controller tracks a reference without steady state error in variable input voltage. The validity of control strategy that proposed is verified from simulation results and experimental results by the DSP(TMS320C32).

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.6
• /
• pp.548-553
• /
• 2004

In this paper, single, two, and three-section microstrip directional couplers are implemented for realizing the high directivity characteristics. The achievement of the high directivity with microstrip configuration is carried out by the distributed capacitor to decrease the even and odd mode phase difference. Capacitive compensation is performed by gap coupling of open stub formed in sub-coupled line. Therefore, insertion loss and power handling capability are not affected by the gap coupling. The proposed structure is easy to fabricate and incorporate another microwave device due to the planner microstrip. We designed and fabricated single, two, and three-section directional coupler with 20 ㏈ coupling. In spite of microstrip structure, the capacitive compensation structure shows 30 ㏈, 27 ㏈, and 25 ㏈ of directivity in single, two, and three-section directional couplers, respectively.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.6
• /
• pp.50-56
• /
• 2015

An efficient fast response hysteretic buck converter suitable for mobile application is propoesed. The problems of large output ripple and difficulty in using of small power inductor that conventional hysteretic converter has are improved by adding ramp generator. and the changeable switching frequency with load current is fixed by adding a delay time control circuit composed of PLL structure resulting in decrease of EMI noise. The circuits are implemented by using BCDMOS 0.35um 2-polt 4-metal process. Measurement results show that the converter operates with a switching frequency of 1.85MHz when drives 80mA load current. As the converter drives over 170mA load current, the switching frequency is fixed on 2MHz. The converter has output ripple voltage of less 20mV and more than efficiency 85% with 50~500mA laod current condition.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.12
• /
• pp.66-71
• /
• 2014

This paper presents an analog front-end integrated circuit (IC) for medical ultrasound imaging systems using standard $0.18-{\mu}m$ CMOS process. The proposed front-end circuit includes the transmit part which consists of 15-V high-voltage pulser operating at 2.6 MHz, and the receive part which consists of switch and a low-power low-noise preamplifier. Depending on the operation mode, the output driver in the transmit pulser can be reconfigured as the switch in the receive path and thus the area of the overall front-end IC is reduced by over 70% in comparison to previous work. The designed single-channel front-end prototype consumes less than $0.045mm^2$ of core area and can be utilized as a key building block in highly-integrated multi-array ultrasound medical imaging systems.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.10 no.12
• /
• pp.1329-1336
• /
• 2015

Due to the advances in hardware technologies for low-power CMOS cameras, there have been various researches on wireless video sensor network(WVSN) applications including agricultural monitoring and environmental tracking. In such a system, its core technologies include video compression and wireless transmission. Since data of video sensors are bigger than those of other sensors, it is particularly necessary to estimate precisely the traffic after video encoding. In this paper, we present an estimation method for the encoded video traffic in WVSN networks. To estimate traffic characteristics accurately, the proposed method first measures complexities of frames and then applies them to the bit rate estimation adaptively. It is shown by experimental results that the proposed method improves the estimation of bit rate characteristics by more than 12% as compared to the existing method.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.5
• /
• pp.39-48
• /
• 2000

We newly proposed a polymer based vertical asymmetric optical coupler, which was characterized by simple fabricating procedure and short coupling length. And we fabricated a thermo-optic modulator using the polymeric optical coupler. We optimized the proposed device by coupling characteristic analysis. In a TE polarized 1.33${\mu}{\textrm}{m}$ wavelength, we obtained very short coupling length(L=277.6${\mu}{\textrm}{m}$) with 0.4${\mu}{\textrm}{m}$ thickness of middle layer, high coupling efficiency(94%), and asymmetric vertical waveguides with n$_{u}$ = 1.522, n$_{l}$ = 1.51. We implemented vortical asymmetric thermo-optic modulator with lower inverted rib waveguide and upper slab waveguide. In the 600Hz bandwidth and 4.5㎽ input power, the extinction ratio of the mode was 17㏈ with an insertion loss of 4.5㏈.