• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.12
• /
• pp.9-17
• /
• 2006

An experimental study was carried out to examine the behavior of the unsteady boundary layer. An NACA 0012 airfoil with aspect ratio of 2.7 was set vertically in a test section, which is sinusoidally pitched about the quarter chord. The oscillating amplitude is from -6$^{\circ}$ to +6$^{\circ}$ and the mean angle of attack is 0$^{\circ}$. Surface mounted probes (Glue-on probes) were employed to measure the surface flow of the boundary layer. Measurements were made at free-stream velocities of 1.98, 2.83, and 4.03m/s, and the corresponding Reynolds numbers based on the chord length were 2.3$\times$104, 3.3$\times$104 and 4.8$\times$104, respectively. The reduced frequency is fixed as 0.1 in all cases. The results show that the surface position of minimum shear stress and of boundary layer break-down can be discerned in the Reynolds number between 2.3$\times$104 and 3.3$\times$104.

• Polymer(Korea)
• /
• v.24 no.3
• /
• pp.326-332
• /
• 2000

The effects of sizing agent on the final mechanical properties of the glass fiber/unsaturated polyester composites were investigated by contact angle measurements at room temperature. In this work, glass fibers were coated by poly(vinyl alcohol), polyester, and epoxy type sizing agent and each property was compared. Contact angles of the sized glass fiber were measured by the wicking method based on Washburn equation using deionized water and diiodomethane as testing liquids. As an experimental result, the surface free energy calculated from contact angle showed the highest value in case of the glass fiber coated by epoxy sizing agent. From measurements of interlaminar shear strength (ILSS) and fracture toughness ( $K_{IC}$ ) of the composites, it was found that the sizing treatment on fibers could improve the fiber/matrix interfacial adhesion, resulting in growing the final mechanical properties. This was due to the enhanced surface free energy of glass fibers in a composite system.

• Korean Journal of Materials Research
• /
• v.4 no.8
• /
• pp.945-951
• /
• 1994

In order to elucidate the extrusion characteristics of $SiC_{p}$/6061 Al composite, defomation resistance, $K_{w}$ was determined using the empirical formula suggested by Watanabe et al, and also extrusion pressure was measured using the extrusion press with a capacity of 350 ton. The $K_{w}$ which are propotional to extrudability, was increased with increasing volume fraction of reinforcement, $SiC_{p}$, but decreased with increasing the particle size. The peaks of maximum extrusion pressure in curves of extrusion force vs ram stroke were changed sharply with decreasing the particle size. The elevated extrustion temperature resulted in the decreased $K_{w}$ and extrusion pressure, but caused the surface tearing of extrusion composite bars. The results showed that extrudability of the composite billets is depend on the extrusion conditions as well as the characteristics of reinforcement, $SiC_{p}$.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.18 no.1
• /
• pp.4011-4020
• /
• 1976

본논문은 북해도대학심사학위논문으로 총면수 143면인 영문으로 되어 있고 도 48, 표 7, 문묵 66부도, 부표 20면이있음. Plow는 옛부터 발달한 농구이기 때문에 많은 연구가 행하여졌지만 복잡한 물리성을 가준 토양을 대상으로 하는 기계이기 때문에 미해결의 문제도 적지않다. 이견인저항에 대하여 토양의 종류 및 조건을 변경하면서 실제의 포장에서 조직적으로 행한 실험은 극히 적고, 하물며 우리나라의 쟁기에 관한 연구는 거의없다. 본논문은 쟁기의 특징을 구명하고, 그의 개량, 발달에 기여하기 위한 기기자료를 획득코저 실시한 것이다. 1. 쟁기와 플라우의 구조 및 그의 차이 특징을 명백히하고 이체에 걸리는 각종의 저항의 내용 또는 그 비율등에 대하여 과거의 연구성과를 소개하였다. 2. 발달사 ; 플라우는 B.C. 2000년경에 녹각, 목지의 인력용의 경운용구에서 발달하고, 동양이도 기원은 대체로 같고 발달과정이 다를 뿐이다. 쟁기는 양자강연안에 기원을 가진 지나이가 신라와 백제에 도입되여 차차 발달하고, 지역적인 특징을 가지게 되었다. 3. 본장은 쟁기의 견인력에 관한 이론적해석을하고, 쟁기의 진행에 의해 층상으로 전단되는 전단저항을 구하고 쟁기의 표면 및 지측판과 토양과의 마찰력, 그리고 토양의 이동의 관성력을 쟁기의 견인저항에 관련되는 주요한 "힘"으로 생각하고 진행방면, 수직방면의 힘의 성분의 평형을 고려하여 식 10. 12를 유도 하였다. 4. 본장에서는 실험계획, 방법 공시기, 공시포장등을 기록하고, 축력용의 쟁기와 플라우를 사용하여 전지 4종 답 2종의 포장에서 실험하는데 견인력계와 자동경심측정기를 사용하였다. 5. 실험결과 및 고찰; 경심과 견인저항 Dp와의 관계는 식 10. 12와 갈이 표시되고, 실제의 제치를 대입하여 이론식을 유도하였으니 직선에 가까운 관계가 있고, 실험결과는 조금 곡선에 가까워졌다. 그리고, 토양의 물리성이 견인력Dp에의 영향을 세밀히 검토하였다. 쟁기의 견인비저항에 있어서도 식 12에서 {{{{K=AT+ { B} over {T } +C}}}}로 표시할수 있기 때문에 최소치를 표시하는 경심이 존재하고 이값은 쟁기나 플라우폭의{{{{ { 1} over {2 } }}}} 즉 10m정도이고 쟁기는 비저항이 0.llkg/$\textrm{cm}^2$에서 0.39kg/$\textrm{cm}^2$이였다. 그러나 이 비저항도 토양의 물리성이 많은 영향을 미치고 있다. 6. 요약 및 결론 ; 이상의 장에서 검토 고찰한 결과만을 기재하고 플라우는 쟁기에 비해 견인저항 및 비저항이 논에서나 밭에서 대로 나타난 것이 특이하다. 이상의 내용을 지면관계로 3회에 거쳐 요약 발표합니다.

• Food Science of Animal Resources
• /
• v.33 no.2
• /
• pp.287-293
• /
• 2013

This study was conducted to investigate the effect of quality grade on the physicochemical and sensory properties of Hanwoo beef on the basis of four quality grades (grade $1^{{+}{+}}$, $1^{+}$, 1, and 2). Significantly decreased levels of myoglobin content (from 12.73 mg/g to 7.90 mg/g) and Warner-Bratzler shear force (WBs) (from 28.01 kg to 14.03 kg) were found with reduction in quality grade (p<0.05). In contrast, increasing quality grade correlated with significant increase in crude fat contents (from 8.18% to 19.55%). Crude fat contents showed a negative correlation with moisture content (r=-0.966), myoglobin content (r=-0.998), and WBs (r=-0.969). In sensory evaluation experiments it was revealed that quality grades were associated with significantly altered (all p<0.05) flavor, taste, juiciness, tenderness, and overall acceptability. Moisture contents showed negative correlation with taste (r=-0.969) and overall acceptability (r=-0.988). Crude fat contents showed significant correlation with taste (r=0.971), tenderness (r=0.983) and overall acceptability (r=0.968). WBs showed negative correlation with taste (r=-0.957) and overall acceptability (-0.978). The marbling score of fresh meat showed significant correlation with taste (r=0.958), juiciness (r=0.953), and overall acceptance of cooked meat. These results could be used as a fundamental dataset to evaluate the effect of quality grade on the physicochemical and sensory characteristics of Hanwoo beef.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.6C
• /
• pp.407-419
• /
• 2006

Situations where support is provided solely in shaft resistance of drilled shafts are where the base of the drilled hole cannot be cleaned so that it is uncertain that any end bearing support will be developed. Alternatively, where sound bed rock underlies low strength overburden material, it may be possible to achieve the required support in end bearing on the rock only, and assume that no support is developed in the overburden. However, where the drilled shaft is drilled some depth into sound rock, a combination of side wall resistance and end bearing can be assumed. Both theoretical and field studies of the performance of rock socketed drilled shafts show that the major portion of applied load is usually carried in side wall resistance. Normal stress at the rock-concrete interface is induced by two mechanisms. First, application of a compressive load on the top of the pile results in elastic dilation of the concrete, and second, shear displacement at the rough surface of the drilled hole results in mechanical dilation of the interface. If the stiffness of the material surrounding the socket with respect to normal displacement is constant, then the normal stress will increase with increasing applied load, and there will be a corresponding increase in the shear strength. In this study, the numerical analyses are carried out to investigate the behavioral characteristics of side of rock socketed drilled shafts. The cause of non-linear head load-settlement relationship and failure mechanism at side are also investigated properly and the design charts are suggested and verified for the leading to greater efficiency and reliability in the pile design.

• Journal of the Microelectronics and Packaging Society
• /
• v.27 no.3
• /
• pp.55-60
• /
• 2020

The recent semiconductor packaging technology is evolving into a high-performance system-in-packaging (SIP) structure, and copper-to-copper bonding process becomes an important core technology to realize SIP. Copper-to-copper bonding process faces challenges such as copper oxidation and high temperature and high pressure process conditions. In this study, the bonding interface quality of low-temperature copper-to-copper bonding using a two-step plasma treatment was investigated through quantitative bonding strength measurements. Our two-step plasma treatment formed copper nitride layer on copper surface which enables low-temperature copper bonding. The bonding strength was evaluated by the four-point bending test method and the shear test method, and the average bonding shear strength was 30.40 MPa, showing that the copper-to-copper bonding process using a two-step plasma process had excellent bonding strength.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.12
• /
• pp.1591-1597
• /
• 2012

Adherend samples were made from unsaturated polyester and woven and mat glass fibers by the hand layup and vacuum methods. The mechanical properties of the adhesive, composite adherends, and terminal-joint and secondary-joint specimens were determined experimentally. Combinations of the experiment results and the bonding theory were used in this study. The maximum and average shear stresses were calculated based on the maximum tensile force and geometry parameters of the joint specimens. The results of the maximum and average shear stresses were compared and evaluated for six joints. The results showed that the grinding and grind/acetone joint had the highest strength among three types of terminal-joints. Similarly, the mat-mat and mat-woven joints had the highest strength among three types of secondary-joints with the same value. Conversely, no treatment and woven-woven bonding had very low strength. In each case, failure occurred always at two ends and then moved toward the middle area of the overlap length.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.47 no.1
• /
• pp.26-34
• /
• 2019

In this paper, a coarse lunar soil model is developed using discrete element method and its computed physical properties are compared with those of the actual lunar soil for its validation. The surface of the actual moon consists of numerous craters and rocks of various sizes, and it is covered with fine dry soil which seriously affects the landing stability of the lunar lander. Therefore, in consideration of the environment of the lunar regolith, the lunar soil is realized using discrete element method. To validate the coarse model of lunar soil, the simulations of the indentation test and the direct shear test are performed to check the physical properties(indentation depth, cohesion stress, internal friction angle). To examine the performance of the proposed model, the drop simulation of finite element model of single-leg landing gear is performed on proposed soil models with different particle diameters. The impact load delivered to the strut of the lander is compared to test results.

• Polymer(Korea)
• /
• v.36 no.5
• /
• pp.612-616
• /
• 2012

In this work, the effect of chemical treatments of multi-walled carbon nanotubes (MWNTs) on the mechanical interfacial properties of carbon fiber fabric-reinforced composites was investigated. The surface properties of the MWNTs were determined by acid and base values, Fourier transform infrared spectroscopy (FTIR), and X-ray photoelectron spectroscopy (XPS) analyses. The mechanical interfacial properties of the composites were assessed by interlaminar shear stress (ILSS) and critical stress intensity factor ($K_{IC}$). The chemical treatments based on acid and base reactions led to a significant change of surface characteristics of the MWNTs, especially A-MWNTs/carbon fibers/epoxy composites had higher mechanical properties than those of B-MWNTs and non-treated MWNTs/carbon fibers/epoxy composites. These results were probably due to the improvement of interfacial bonding strength, resulting from the acid-base interaction and hydrogen bonding between the epoxy resins and the MWNT fillers.