• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.2
• /
• pp.252-261
• /
• 1988

Through the careful interpretation of the results of the cutting tests carried out in this study, it is found that under the cutting conditions when the internal shear of the chips take place the cutting can be treated essentially as a steady state problem. A new shear angle equation has been developed employing the conditions of force and moment equilibrium about the tool edge and the stress distribution model suggested by Zorev.The equation contains the chip-tool contact length C and stress distribution index n as important parameters.

• Journal of the Korean Geotechnical Society
• /
• v.17 no.4
• /
• pp.301-315
• /
• 2001

본 연구에서는 최근 5년간 국내 각 지역에서 채취한 802개의 절리면 시료에 대하여 전단시험을 실시하여 얻은 결과를 이용하여, 절리면의 여러 공학적 성질들을 조사, 연구하였다. 절리면 전단시험에서 얻어진 최대마찰각 및 잔류마찰각을 지체구조별, 암종별로 분류하고 통계적으로 구하였으며, Barton의 전단강도식의 입력변수인 JRC, JCS를 측정하고 Barton식의 적용성에 대해서도 검토하였다. 그 결과 설계의 기초자료로 활용할 수 있는 지역별, 주요 암종별 최대마찰각, 잔류마찰각을 제시하였다. 또한, JRC, JCS, 수직응력에 따른 마찰각과 전단강성 및 팽창각의 변화를 분석하였다. 마지막으로, Barton의 식에서 구한 이론적 전단강도와 이 실험에서 얻어진 전단강도를 비교한 결과, Barton의 경험식은 높은 상관도로 암석 절리면 전단강도를 예측할 수 있음을 확인하였다.

• Korean Journal of Agricultural Science
• /
• v.11 no.2
• /
• pp.278-283
• /
• 1984

Shearing characteristics of cornstalks were investigated under quasi-static conditions at various knife approach angles and shear angles in order to determine their importance to the cutting action of mowers. Corn variety used in this study was pioneer that was grown in the field of Chungnam National University. The results obtained were as follows: 1. The shearing process had two shearing stages in cornstalks, which was different from those of rice and other forage crops due to the hard crust. 2. Force and energy of shear were decreased progresively with height of the cornstalks. 3. The minimum shear force occured at shear angle of about $60^{\circ}$ and approach angle of about $10^{\circ}$ 4. The condition of minimum shear energy coincides with that of minimum shear force. 5. Effects of knife approach angles were more significant than those of shear angle for force and energy of shear.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.11 no.1
• /
• pp.27-33
• /
• 2007

The shear spinning has been used to produce thin angled cone of parts, with reduced forming force and enhanced mechanical and surface quality for a good finished part, compared with other method formed parts. So shear spinning technique is used widely in industrial production. Especially shear spinning and flow forming techniques are used frequently in automotive, aerial, defense industry. In this paper, finite element method analysis of shear spinning for a cone shape workpiece is carried out to study effects of forming depth and lead angle on forming force. The axial and radial forces on several forming depth and lead angle conditions are obtained.

• Journal of the Korean Geotechnical Society
• /
• v.16 no.6
• /
• pp.161-172
• /
• 2000

자연암석절리 및 인공 절리에 대하여 일정수직응력제어, 일정 수직하중제어 그리고 무한 강성제어가 가능한 암석 절리면 전단기 시험기를 개발하였다. 이 시험기는 전단변위에 의한 첩촉면적의 변화량을 계산하여 하중변화량을 조절하여 일정수직응력상태를 유지한다. 수직하중에 따른 시험기 강성에 의한 변화향이 제어 프로그램 내에서 제어되어 순수한 시편의 변위량을 출력하도록 하였다. 전단하중에 따른 시험기 강성에 의한 변위량은 상, 하부 전단상자의 상대변위 측정으로 최소화하였다. 전단거동 중의 자유도는 전당방향에 대하여 수평이도, 연직이동, 피칭, 롤링이 가능하도록 하였다. 자연절리면을 모사한 석고시편에 대하여 일정 수직응력 제어, 일정수직하중제어 그리고 무한 강성제어 조건으로 시험하여 제어상태 검증 및 비교를 하였다. 또한 경사각이 16.7˚와 22.6˚인 톱니형 시편에 대하여 시험한 결과 경사각 16.7˚와 22.6˚는 JRC로 10과 15를 나타내었으며, 첨두팽창각이 첨두전단강도에서 발생되며, Barton의 모델과 잘 일치함을 보였다.

• Journal of the Korean Geotechnical Society
• /
• v.31 no.9
• /
• pp.17-27
• /
• 2015

We perform a series of experimental tests to evaluate whether the shear strength of clean sands can be reliably predicted from shear wave velocity. Isotropic drained triaxial tests on clean sands reconstituted at different relative densities are performed to measure the shear strength and bender elements are used to measure the shear wave velocity. Laboratory tests reveal that a correlation between shear wave velocity, void ratio, and confining pressure can be made. The correlation can be used to determine the void ratio from measured shear wave velocity, from which the shear strength is predicted. We also show that a unique relationship exists between maximum shear modulus and effective axial stress at failure. The accuracy of the equation can be enhanced by including the normalized confining pressure in the equation. Comparisons between measured and predicted effective friction angle demonstrate that the proposed equation can accurately predict the internal friction angle of granular soils, accounting for the effect of the relative density, from shear wave velocity.

• Tunnel and Underground Space
• /
• v.29 no.5
• /
• pp.292-304
• /
• 2019

Limestone joint surfaces with smooth roughness were experimented by means of both the individual direct shear tests based on the KSRM standard test method and the multi-stage direct shear test to apply the stepwise vertical stresses. Changes in the roughness of the joint surfaces before and after the shear tests were examined and the difference between the two kinds of tests mentioned above was analyzed. In both tests, the shear resistance increased as the joint roughness increased and the maximum shear stress required for shearing the joint surface increased as the vertical stress increased. The peak friction angle obtained by the multi-stage direct shear tests was only 63% of that obtained by the individual direct shear tests. In the multi-stage direct shear test, the initial engagement of the concave-convex parts changes frequently during stepwise shearing process, which deforms the original roughness of a joint surface. Accordingly, the individual direct shear test is thought to be more effective when obtaining the friction angle of the rock joint surfaces. Limestone joint surfaces with smooth roughness of JRC value 4~8 were found to have peak friction angle of $47^{\circ}$, residual friction angle of $38^{\circ}$ and cohesion of 37 kPa.

• Journal of the Korea Concrete Institute
• /
• v.14 no.6
• /
• pp.910-921
• /
• 2002

For the prediction of shear behavior of reinforced concrete beams, this paper proposed Transformation Angle Truss Model (TATM) considered bending moment effect. Shear stress-strain relationship obtained from the TATM was agreed well with test results conducted by this study Further, shear strength obtained from the TATM was compared to the experimentally observed results of 170 reinforced concrete beams which had various shear span ratios shapes of support and shapes of cross section. The shear strength of reinforced concrete beams obtained from test was better predicted by the TATM with 0.96 in average and 11.9％ in coefficient of variation than by other truss models. And the ratio of experimental results to theoretical results obtained from the TATM was almost constant regardless of the η and a/d.

• Composites Research
• /
• v.17 no.1
• /
• pp.38-46
• /
• 2004

This paper aims to correlate the micro-mechanical behaviour of tow geometry with applied in-plane forces during deformation of dry woven carbon-fibre fabric. These in-plane forces lead to differences in tow reorganisation during deformation and so changes in the way in which 'lock-up' occurs. In this paper, deformation of micro-mechanical parameters such as tow interval, crimp angle, change in tow amplitude and wavelength are investigated. To observe the micro-deformation of the fabric structure, appropriate specimens from bias extension and biaxial tests are sectioned and observed under the microscope. It was found that different loading conditions cause geometric deferences in the tow architecture. The variation in deformed tow geometry with shear angle is fitted using a simple parametric model.

• Journal of the Korean Geotechnical Society
• /
• v.17 no.4
• /
• pp.57-70
• /
• 2001

한계상태이론은 정규압밀 및 과압밀시료에 대한 비배수 전단강도와 간극수압계수에 관한 식을 제안하고 있는데, 이 식은 3가지 상수를 포함하고 있다. 한계상태상수(M), 한계상태 간격비(${\gamma}$), 한계상태 간극수압계수(Λ)가 바로 그것이며, 이러한 상수는 각 모델 및 구하는 방법에 따라 그 차이가 발생함으로서, 전단강도 및 간극수압계수의 예측시 적지 않은 영향을 미치게 된다. 본 논문에서는 재 성형된 이암풍화토를 이용하여 등방삼축압축시험을 정규압밀과 과압밀로 나누어 실시하고 그 결과를 분석하였으며 이를 토대로 각 모델 및 방법에 따른 상수를 도출하였다. 그리고 이러한 상수의 차이가 비배수 전단강도 및 간극수압계수의 예측에 미치는 영향을 살펴보았다. 시험결과 정규압밀시료의 경우 각 상수의 변화에 따른 비배수 전단강도 및 간극수압계수는 상당한 차이를 보였으며, 한계상태간격비와 Λ값을 강도비로부터 얻어진 값을 사용한 경우가 결과치에 가장 잘 근접함을 알 수 있었다. 과압밀시료의 경우 역시 이들 상수에 따라 전단강도의 변화폭이 크게 나타났으며 정규압밀과 마찬가지로 강도비에서부터 도출된 상수를 적요한 경우 실측치에 가장 근접하였다. 반면 간극수압계수의 예측시에는 상수에 따른 변화폭이 크지 않았으며, 특히 과압밀비가 증가할수록 각 상수에 대한 영향이 작게 나타났다.