• Title/Summary/Keyword: 적치장

Search Result 108, Processing Time 0.033 seconds

Deformation Characteristics of a Slope at a Coal Waste Depot through Analysis of Monitoring Results (계측결과 분석을 통한 석탄폐석 적치장 사면의 변형 특성)

  • Cho, Yong-Chan;Song, Young-Suk
    • The Journal of Engineering Geology
    • /
    • v.23 no.1
    • /
    • pp.19-27
    • /
    • 2013
  • Deformation of a slope at a coal waste depot and the natural slope under the depot was surveyed and investigated at Dogye village in Samcheock city, Gangwon Province. To investigate the behaviors of the slopes, wire sensors and a rain gauge were installed on the crest of the waste depot slope and inclinometers were installed in the natural slope. The results of deformation monitoring at the crest of the waste depot slope using wire sensors revealed increased deformation with increasing cumulative rainfall. The results of monitoring horizontal deformation of the natural slope revealed that maximum horizontal deformation was also affected by cumulative precipitation. However, the groundwater level at the natural slope showed no change with rainfall. These measurements confirm that deformation at coal mine waste depots is closely related to precipitation, indicating that self-loading at such depots increases with rainfall infiltration, thus causing deformation of the waste depot slope. In addition, increasing the self-load of the coal mine waste depot may cause deformation of the underlying natural slope.

임기광산 주변 수질특성 변화연구

  • 임길재;정영욱;지상우;홍성규
    • Proceedings of the Korean Society of Soil and Groundwater Environment Conference
    • /
    • 2004.09a
    • /
    • pp.385-389
    • /
    • 2004
  • 임기납석광산 폐석적치장 상부의 계곡수로부터 폐석적치장 하부인 수영강 합수지점까지 수계를 따라 물시료 12개 지점을 대상으로 수질 및 안정동위원소 분석을 수행하였다. 폐석적치장으로부터 pH가 2.83이고 Fe, Al, Mn 등으로 심하게 오염된 산성배수가 유출되어 계곡수를 오염시키며 수계의 수질은 $Ca^{2+}$-SO$_{4}$$^{2-}$ 형태로 변화되고 폐석적치장 주변 수로에 적화현상을 유발하고 있다. 또한 안정동위원소 분석결과 임기납석광산 인근 수계에 가장 큰 오염부하를 유발하는 요소인 침출수(산성배수)의 기원은 강수기원으로 판단된다. 이는 폐석침출수 오염원 평가 및 처리에 유용한 자료로 이용 될 수 있을 것이다.

  • PDF

The Present Status of Concrete Products for Buildings (건축용 콘크리트 공장제품의 현황)

  • 김진만;조성현
    • Magazine of the Korea Concrete Institute
    • /
    • v.14 no.6
    • /
    • pp.22-31
    • /
    • 2002
  • 콘크리트 블록에는 속빈 콘크리트 블록, 치장 콘크리트 블록, 형틀 콘크리트 블록, 콘크리트 적층 블록 등이 있고, 콘크리트 적층 블록을 제외하면 모두 건축용으로 널리 쓰이는 재료이다. (1) 속빈 콘크리트 블록 속빈 콘크리트 블록이란 보강근을 삽입하는 속빈 부분을 갖고, 블록 벽체로 외력을 부담하는 것을 말한다. 속빈 콘크리트 블록은 건물의 경량화와 시공 기간의 단축이 가능하기 때문에 (그림 1)과 같이 벽체용으로 사용되거나 또는 칸막이용 등으로 많이 사용되는 대표적인 조적재이다 (2) 치장 콘크리트 블록 치장 콘크리트 블록은 철근으로 보강할 수 있는 공동이 있고, 미리 표면에 연마, 절삭, 씻어 내기, 쪼아 내기. 스플릿, 슬럼프, 리브붙임 등의 치장 마무리가 되어 있는 블록을 말한다. 도장 또는 착색만에 의한 치장 블록은 포함하지 않고 있다. 치장 블록은 주로 (그림 2)와 같이 담장에 많이 사용되고 있다. (3) 형틀 콘크리트 블록 형틀 콘크리트 블록은 형틀 콘크리트 블록조에 사용되는 것을 형틀 콘크리트 블록조란 형틀 블록을 조합하여 형틀로 하고, 그 중공부에 철근을 배치하고 콘크리트를 타설하여 내력벽을 형성하는 건축구조를 말한다. 형틀 블록을 조적한 후 외부에 나타나는 면에는 스플릿, 연마, 절삭, 씻어 내기, 쪼아 내기 등의 치장을 하기도 한다.(중략)

Segmentation Foundation Model-based Automated Yard Management Algorithm (의미론적 분할 기반 모델을 이용한 조선소 사외 적치장 객체 자동 관리 기술)

  • Mingyu Jeong;Jeonghyun Noh;Janghyun Kim;Seongheon Ha;Taeseon Kang;Byounghak Lee;Kiryong Kang;Junhyeon Kim;Jinsun Park
    • Smart Media Journal
    • /
    • v.13 no.2
    • /
    • pp.52-61
    • /
    • 2024
  • In the shipyard, aerial images are acquired at regular intervals using Unmanned Aerial Vehicles (UAVs) for the management of external storage yards. These images are then investigated by humans to manage the status of the storage yards. This method requires a significant amount of time and manpower especially for large areas. In this paper, we propose an automated management technology based on a semantic segmentation foundation model to address these challenges and accurately assess the status of external storage yards. In addition, as there is insufficient publicly available dataset for external storage yards, we collected a small-scale dataset for external storage yards objects and equipment. Using this dataset, we fine-tune an object detector and extract initial object candidates. They are utilized as prompts for the Segment Anything Model(SAM) to obtain precise semantic segmentation results. Furthermore, to facilitate continuous storage yards dataset collection, we propose a training data generation pipeline using SAM. Our proposed method has achieved 4.00%p higher performance compared to those of previous semantic segmentation methods on average. Specifically, our method has achieved 5.08% higher performance than that of SegFormer.

The Acid Rock Drainage and Hydraulic Characteristics of the Waste Rock Dump (폐석적치장의 산성배수발생 및 수리특성 분석)

  • Cheong, Young Wook;Ji, Sang Woo;Yim, Gil Jae
    • Journal of the Korean GEO-environmental Society
    • /
    • v.5 no.4
    • /
    • pp.13-24
    • /
    • 2004
  • This study was carried out to plan the prevention of the generation and discharge of Acid Rock Drainage (ARD). The Acid Base Accounting(ABA) test was performed for geological materials such as pit wall, waste rock and stream sediments near the Imgi abandoned pyrophyllite mine in Busan, Korea. In addition, hydraulic characteristics were tested with the disk tension infiltrometer around the waste rock dump. Maximum Potential Acidity(MPA) of geological materials near the Imgi mine was 246.942kg $H_2SO_4/t$, and maximum Acid Neutralising Capacity(ANC) was 8.7kg $H_2SO_4/t$. These results indicate the pit wall and waste rock, except most of stream sediments are acid generating geological materials. These have salt and free hydrogen ion which resulted from oxidation of sulfides. Hence they could be convert rain water to acid rock drainage. Although the waste rock dump of the Imgi mine have very low infiltration rate, slopes of the waste rock dump have many "V" type erosion gullies and multi-layers. These gullies and multi-layers have coarse clastic particle layers which have very large hydraulic conductivity. Through this coarse clastic particle layer a large part of rain flow into ground. And also this layer could function as aeration path which induced oxidation of sulfide minerals and generation of ARD continuously.

  • PDF

Assessment of the Cause and Pathway of Contamination and Sustainability in an Abandoned Mine (폐광산 오염원인 분석 및 오염경로, 향후 지속가능성에 대한 평가)

  • Kim, Min Gyu;Kim, Ki-Joon;Jeong, Gyo-Cheol
    • The Journal of Engineering Geology
    • /
    • v.28 no.3
    • /
    • pp.411-429
    • /
    • 2018
  • Daeyoung mine (also called "Daema mine") produced gold and silver from mainly gold- and silver-bearing quartz veins. The mine tailings are a waste hazard, but most of the tailings were swept away or dispersed throughout the area around the mine long before the tailing dump areas were transformed into agricultural land. Soil liner and protection facilities, such as retaining walls, were constructed in the mine area to prevent the loss of tailings. The content of the tailings is 3,424.41~3,803.61 mg/kg, which exceeds the safety standard by a factor of 45. In addition, contamination was detected near agricultural areas and in the sediments in downstream drainage channels. A high level of As contamination was concentrated near the waste tailings yard; comparaable levels were detected in agricultural areas close to streams that ran through the waste dump yard, whereas the levels were much lower in areas far from the streams. The contamination in stream sediments showed a gradual decrease with distance from the mine waste yard. Based on these contamination patterns, we concluded that there are two main paths that affect the spread of contaminants: (1) loss of mine waste, and (2) the introduction of mine waste into agricultural areas by floods after transportation by streams. The agricultural areas contaminated by mass inflow of mine waste can act as contamination sources themselves, affecting other agricultural areas through the diffusion of contaminants. At present, although the measured effect in minimal, sediments in streams are contaminated by exposed mine waste and surface liners. It is possible for contaminants to diffuse or spread into nearby areas if heavy elements trapped in soil grains in contaminated agricultural areas leach out as soil solution or contaminant particles during diffusion into the water supply.

Study of Monitoring Methods for Maintenance Management of Tailings Dams (광물찌꺼기 적치장 유지관리를 위한 모니터링 방안 연구)

  • Oh, Sam-Ju;Kim, Ki-Joon;Song, Jea-Yong;Choi, Uikyu
    • The Journal of Engineering Geology
    • /
    • v.26 no.4
    • /
    • pp.473-484
    • /
    • 2016
  • This study aims to establish a monitoring method for managing the effective maintenance of tailings dams. The monitoring of a tailings dump area involves several parameters and their investigation through a selection of evaluation items. The extents of defects and progressive failures also need to be effectively estimated. Therefore, the monitoring items can be subdivided into categories relating to the retaining wall structure (concrete wall, reinforcing stone wall, mesh gabions) and general facilities (liner, covering soil, slope, tailings, rain protection facility, leachate, planting), and quantitative evaluations can then be conducted for each condition. In doing so, we developed a systematic monitoring method that assesses the dam maintenance condition with grades and scores. The field application of the monitoring method results showed it to provide a more detailed evaluation than existing monitoring methods: the method detected an additional 16 defects missed by conventional methods. The evaluation gave scores of 89.3, 22.2, and 27.8 to the Geumjang mine tailings dam, the Gupoong mine tailings dam, and the Hwachun mine tailings dam, respectively. The advanced method can provide quantitative evaluation and perform detailed monitoring of the dams. This quantitative evaluation can be used to decide on maintenance priorities, select the main management items, and establish schedules of maintenance.

Current Occurrence and Heavy Metal Contamination Assessment of Seepage from Mine Waste Dumping Sites in Korea (국내 광산폐기물 적치장 침출수 발생 현황 및 중금속 오염도 평가)

  • Park, Chang Koo;Kim, Jeong Wook;Jung, Myung Chae;Park, Hyun Sung;Kim, Dong Kwan;Oh, Youn Soo
    • Journal of the Korean Society of Mineral and Energy Resources Engineers
    • /
    • v.55 no.6
    • /
    • pp.588-595
    • /
    • 2018
  • This study has focused on evaluation of heavy metal contamination in seepage from 23 mine waste dumping sites in Korea. Seepage samples from the sites were taken and analyzed for heavy metals. The maximum levels (mg/L) in the samples were Al 53.98, As 16.19, Cd 1.15 Cu 37.30, Fe 28.64, Mn 39.00, Ni 0.097, Pb 0.750, and Zn 80.18. Among the sites, six mines were selected as continuous monitoring sites. As results of three months' monitoring of the sites, over the water guidelines for As, Cd, Cu, Fe, Mn, Zn and Al in seepage samples were found at two abandoned Au-Ag mines, Cd, Mn, Zn and Al at two Pb-Zn mines, and As, Fe and Mn at two other Fe-W mines. Therefore, those six mines need continuous monitoring on contamination assessment of seepage due to mining activities.

Proper Monitoring Methods for Safety Management of Tailings Dam (광물찌꺼기적치장의 안전관리를 위한 적정 모니터링 방안 연구)

  • Jung, Myung Chae;Kim, Jeong Wook;Hwang, In-ho;Yang, In Jae;Park, Jay Hyun;Park, Ju Hyun;Kim, Tae Youp
    • Journal of the Korean Society of Mineral and Energy Resources Engineers
    • /
    • v.55 no.6
    • /
    • pp.576-587
    • /
    • 2018
  • This study has focused on analysis factors affecting safety monitoring system at tailings sites, and the evaluation equipment to monitor the factors. Twenty sites at eighteen mines with unsafe conditions were selected to examine the equipment. There were three main factors influenced safety in the sites including surface erosion, piping, and slope instability. In detail, the surface erosion was divided into three sub-factors (planting, soil-topping layer, and tailings), piping into three sub-factors (liner, rain protection facility and leachate), and slop instability was also divided into three sub-factors (slop, concrete wall, and reinforcing wall). As results of in-field measurement, a CCTV was the most effective facility, and electrical resistivity survey, acoustic sensing, thermal liner sensor, structure inclinometer, rainfall meter, and flowmeter were also highly effective. According to applications of the facilities in the unstable tailings, structural defects were mainly found in the piping, which was the most important monitoring factor for safety management of tailings sites.

Shear Strength and Failure Mode of Architectural Masonry Walls (내진보강된 치장조적벽의 파괴특성과 전단강도)

  • Jin, Hee-Yong;Han, Sang-Whan;Park, Young-Mi
    • Proceedings of the Korea Concrete Institute Conference
    • /
    • 2008.04a
    • /
    • pp.89-92
    • /
    • 2008
  • This study investigates the shear behavior of architectural masonry veneer wall reinforced with specific reinforcement details proposed by this study. For this purpose, experimental tests were conducted using one un-reinforced masonry(URM) wall specimen and three reinforced masonry(RM) wall specimens under quasi static cyclic loads. Un-reinforced(plain) masonry wall is expressed that behavior and failure mode are different for aspect ratio(L/H) and axial compressive force. The test variables are wall aspect ratio and presence of reinforcement. These specimens are masonry structure for architectural clading that is not to exist the axial compressive force. thus the axial compressive force is excepted from test variable. Test result, Behavior of specimens are dominated over rocking mode, but final failure modes are combined with different behaviors. And FEMA273 has proposed the equation of shear strength of masonry pier subjected to in-plane loading. Shear strength equations are classified four types of failure mode that is Rocking, and Toe-Crushing, Bed-Joint-Sliding and Diagonal-Tension. FEMA273 equations predict the behavior modes well, but shear strength is shown in different result.

  • PDF