• 대한기계학회논문집
• /
• 제19권3호
• /
• pp.741-750
• /
• 1995

The turbulent buoyancy-driven flow in 2-dimensional enclosed cavities heated from the vertical side is numerically calculated for both cases of a Rayleigh number of 5*10$^{10}$ for air and 2.5*10$^{10}$ for water. Three different turbulence models are considered : standard k-.epsilon. model of Ozoe and low-Reynolds-number model of Lam and Bremhorst, and another low-Reynolds-number model of Davidson. The results indicate that the use of low-Reynolds number models is recommended for the indoor airflow computation, and the results from Davidson model are reasonably close to the reported experimental data. A sensitivity study shows that the amounts of wall-heat transfer and the velocity profiles with the Lam and Bremhorst model largely depend on the choice of the wall function for .epsilon..

• 대한기계학회논문집B
• /
• 제27권12호
• /
• pp.1681-1690
• /
• 2003

The effect of roughness is a change in the velocity and turbulence distributions near the surface. Turbulence models with surface roughness effect are applied to the fully developed flow in a two-dimensional, rough wall channel. Modified wall function model, low-Reynolds number k-$\varepsilon$ model, and k-$\omega$ model are selected for comparison. In order to make a fair comparison, the calculation results are compared with the experimental data. The modified wall function model and the low-Reynolds number k-$\varepsilon$ model require further refinement, while the k-$\omega$ model of Wilcox performs remarkably well over a wide range of roughness values.

• 한국추진공학회지
• /
• 제17권1호
• /
• pp.61-69
• /
• 2013

핀틀 움직임에 의해 발생되는 큰 유동박리에 대해 적합한 2-방정식 난류모델의 압축성계수 보정모델을 판단하기 위하여 수치적 연구를 수행하였다. 난류모델은 저 레이놀즈수 k-${\varepsilon}$ 모델과 k-${\omega}$ SST 모델에 압축성 보정 모델(Wilcox와 Sarkar 모델)을 적용하여, 핀틀 노즐의 세부유동장을 관찰하고 노즐 벽면에서의 압력을 실험데이터와 비교 분석하였다. 마하디스크(Mach disk)의 위치와 박리영역에서의 압력 회복 형태는 난류모델에 따라 다르게 나타났으며, 각 난류모델에 압축성 보정을 적용하여 유동 박리 포획의 정확도를 개선하였다. 압축성이 보정된 k-${\varepsilon}$ 모델이 실험결과와 매우 잘 일치하였다.

• 대한기계학회논문집B
• /
• 제21권7호
• /
• pp.911-918
• /
• 1997

The turbulent viscous wake flows behind a single airfoil, two-dimensional stationary blade row and three-dimensional rotating blade row were calculated, and the numerical results were compared with experimental ones. The numerical technique was based on the SIMPLE algorithm using three turbulent closure models, standard k-.epsilon. model(WFM), low Reynolds number k-.epsilon. model(LRN) and Reynolds stress model (RSM). In the case of a single airfoil, WFM, LRN and RSM presented fairly good velocity distributions in the wake compared with experimental data. In the case of the stationary blade row, LRN and RSM presented better results than WFM for wake velocity distribution, and especially LRN showed best results among these three turbulent models. In the case of the rotating blade row, WFM and LRN showed fairly good agreement with experimental data of the three-dimensional velocity component distributions in the range from hub to mid span region. LRN was also superior to WFM in accuracy of prediction for the wake velocity distribution as same with the cases of a airfoil and the stationary blade row.

• 대한기계학회논문집
• /
• 제16권10호
• /
• pp.1971-1978
• /
• 1992

본 연구에서는 원형 파이프에 원추형 디퓨져가 연결된 덕트 내의 유동장에 대 하여 Launder-Sharma의 저 레이놀즈수 k-.epsilon. 난류모델을 이용하여 수치해석을 수행하였 으며, 수치해석 방법으로는 타원형 방법을 사용하였으며, 앞으로 일반적인 단면의 곡 관이나 스크롤 내부 유동 등의 연구 수행을 감안하여 지배방정식을 일반 비직교 좌표 계로 변환하여 계산을 수행하였다.

• 설비공학논문집
• /
• 제11권2호
• /
• pp.157-166
• /
• 1999

Numerical calculations of turbulent natural convection in an enclosure of the 20 kYA oil-immersed transformer model are presented. The transformer is modelled as two concentric cylinders with different heights and diameters. The thermal boundary layers are well represented in the temperature distributions along the wall of the transformer model. The flow stratification between the hot and cold walls can not be seen in the transformer model. The turbulence eddy viscosity has its maximum at the center of the core and its maximum values at the top of the core are larger than those at the bottom of the core.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집B
• /
• pp.517-522
• /
• 2001

The exit edges of a diffuser are smoothly rounded, and a wall is located perpendicularly to a diffuser exit. The fluid is discharged towards the radial direction of a diffuser after impinging against a wall from a diffuser. In this flow path, pressure loss coefficients have been calculated by the variables of Reynolds number at a diffuser inlet, distance between a diffuser exit and a wall, and turbulence models. As a result, it was calculated that $h/D_0$ ratio between $0.35\sim0.4$ has the minimum pressure loss coefficient regardless of Reynolds number and turbulence models. It was also found that in case of the flow with relatively high Reynolds number at a diffuser inlet, the pressure loss coefficients by RNG $k-\varepsilon$ model have a tendency to be near to those by standard $k-\varepsilon$ model at small ratio of $h/D_0$, but to those by RSM at large ratio.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집B
• /
• pp.428-433
• /
• 2000

The characteristics of unsteady heat transfer and boundary layer flow in the SSME turbine rotor passage are investigated with LRN $k-{\varepsilon}$ turbulence model. The unsteady flow and heat transfer in a rotor blade passage as a result of wake/blade interaction is modeled by the inviscid/boundary-layer flow approach. The relevant governing equations are discretized to a system of finite different equations by means of a BTBCS implicit method. These equations have been solved numerically, for the velocity and temperature fields using TDMA method. Heat flux on the blade surface and flow parameters in the rotor passage are calculated with wake interaction. Numerical results show that velocity, pressure, turbulent kinetic energy and heat flux on the blade surface are varied periodically by wake passing.

• 설비공학논문집
• /
• 제7권2호
• /
• pp.287-297
• /
• 1995

In this study, the geometry consists of a two-dimensional rectangular enclosure with localized heating from below. The size and the location of the heater on the floor has been varied, and one of the vertical walls remains at a low temperature simulating a cold window. The governing equations for momentum, energy and continuity, which are coupled with turbulent equations have been solved using a finite volume method. A low Reynolds number $k-{\varepsilon}$ model has been incorporated to solve the turbulent kinetic energy and the dissipation rate. The heat transfer characteristics and the thermal environmental characteristics of the room have been obtained for various system parameters in a room with a partially heated floor.

• 설비공학논문집
• /
• 제11권6호
• /
• pp.733-739
• /
• 1999

A modified low-Re $k-\varepsilon$ model is used for the calculation of drag-reducing turbulent flow by polymer injection in a pipe. With the viscoelastic model, molecular viscosity in the definition of turbulent viscosity is related to elongations viscosity of the solution to account for the effects of drag reduction. Finite volume method is used for the discretization, and power-law scheme is used as a numerical scheme. Computed dimensionless velocity profiles are in good agreements with the experimental data in case of low drag reductions. However, in case of high drag reductions, they deviate largely from the measurements in the central zone of the flow field.