• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.341-344
• /
• 2008

In this paper, the effect of flame cutting order of tendons on the concrete stress was investigated experimentally. For this, the three slab specimens with 14 tendons were cast and tested. During the detensioning, the longitudinal and transversal strain were measured. Test results showed that the measured strains of transversal stirrups were varied by the cutting order.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1998.05a
• /
• pp.707-712
• /
• 1998

이종 코드에 의한 CE형 발전소의 대형 냉각재 상실 사고 해석이 수행되었다. 이 연구는 상대적으로 최근에 개발된 웨스팅하우스 대형 냉각재 상실 사고 해석 코드를 사용하여 영광 3&4호기의 대형 냉각재 상실 사고를 계산해 봄으로써 CE 대형 냉각재 상실 사고 해석 코드의 개선 방향을 고찰하는 것을 목적으로 하였다. 계산은 가장 제한적인 대형 냉각재 상실 사고의 Blowdown 및 Refill 기간 동안 수행하였다. 이 기간 동안의 RCS내 열수력적 거동 및 연료봉 온도 변화는 CE 대형 냉각재 상실 사고 해석 코드를 사용하여 계산한 경우와 크게 다르지 않음을 확인하였다. 따라서 향후 CE 대형 냉각재 상실 사고 해석 코드의 성능 개설은 Reflood 해석용 코드의 개선 및 개발을 중심으로 이루어져야 한다는 결론을 얻었다.

• Journal of Korean Society of Steel Construction
• /
• v.22 no.3
• /
• pp.219-228
• /
• 2010

This paper describes an experimental research on the structural behavior and the ultimate strength of longitudinally stiffened plates subjected to local, distortional, or mixed-mode buckling under compression. The stiffened plate undergoes local, distortional, or interactive local-distortional buckling according to the flexural rigidity of the plate's longitudinal stiffeners and the width-thickness ratios of the sub-panels of the stiffened plate. A significant post-buckling strength in the local and distortional modes affects the ultimate strength of the longitudinally stiffened plate. Compression tests were conducted on stiffened plates that were fabricated from 4mm-thick SM400 steel plates with a nominal yield stress of 235MPa. A simple strength formula for the Direct Strength Method based on the test results was proposed. This paper proves that the Direct Strength Method can properly predict the ultimate strength of stiffened plates when the local buckling and distortional buckling occur simultaneously or nearly simultaneously.

• Geotechnical Engineering
• /
• v.13 no.1
• /
• pp.159-168
• /
• 1997

In order to investigate the effect of parameters such as orientation and surface roughness of a reinforcing material as well as the water content of the clay matrix on the stress-strain and failure behavior of reinforced clay, uniaxial compression tests were performed on clay samples reinforced with a steel inclusion Test results showed that the increase or decrease in strength of reinforced clay samples was found to depend on the orientation of a steel inclusion as well as water content of clay samples. The possible weakening mechanism induced by reinforcement in clay samples was related to the development of cracks along the tips of interface between steel inclusion and clay matrix. A theoretical interpretation of failure behavior of reinforced clay was made by using fracture mechanics theory, and the experimental results were compared with the theoretical predictions. The predicted crack propagation direction obtained from fracture criteria for a material containing a closed crack with friction agreed reasonably well with the measured values obtained from tests.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.12 no.5
• /
• pp.169-178
• /
• 2008

Compressive flanges of steel box girder is designed based on the ultimate strength behavior of sub-panel which is enclosed with longitudinal stiffeners and transverse stiffeners on appropriate safety factor. However, it is rational that the ultimate strength is calculated considering the various factors such as number and stiffness of longitudinal stiffener, spacing of transverse stiffener, initial deformation and residual stress distribution. In this study, an analysis program based on Folded Plate theory is developed considering the geometric effects and the material nonlinearity. The analysis program is applicated to the steel box girder bridges which is really constructed in domestic.

• 방재와보험
• /
• s.107
• /
• pp.16-20
• /
• 2005

풍수해 사고의 경우 보험사의 위험 분산이 곤란해 심한 재정적 타격을 입을 수 있으며 자율적인 손해율 관리가 어려워 개선방안이 논의되고 있다. 이에 국내 풍수재 관련 보험상품 및 외국의 풍수재 보험 운영사례를 통해 향후 지향해야 할 운영방안을 모색해보도록 하자.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.11
• /
• pp.762-769
• /
• 2017

The extensional stiffness in quasi-isotropic laminates is uniform in the radial direction, but the bending stiffness varies radially due to the stacking sequence. This paper addresses the directional dependency of the bending stiffness and its radial variation in three types of quasi-isotropic laminate reflectors consisting of unidirectional fiber composite materials (UDM) and randomly distributed composite materials (short fiber, RDM). The extensional stiffness and bending stiffness in optical reflectors using RDM are uniform, while the bending stiffness in those using UDM varies radially from 11% to 26%. Also, the stiffness sensitivity, such as the bend-twist or bend-torsion effect, due to the differences in the stiffness value in the composite, is large. These factors are problematic in the optical field requiring precision surfaces. Utilizing RDM might be one way to eliminate the presence of bending stiffness in composite mirror substrates.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.429-432
• /
• 2009

The deformation and burst pressure of composite motor case highly depends on fiber material properties. Therefore, measuring exact fiber material properties is a priority item to develop a advanced composite motor case. However, the fiber material properties in composite motor case is very sensitive on the various processing variables (equipment, operator and environmental condition etc..)and size effect, so the fiber material properties can't be measured exactly from the existing specimen test method. This paper suggests a newly developed test method, hoop ring test, that is capable of pressure testing with ring specimens extracted from real composite motor case. The results of hoop ring test showed excellent agreement with measured fiber material properties from hydro-burst test with full scale composite motor cases.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.8
• /
• pp.665-672
• /
• 2013

One of the major causes of stiffness and strength degradations in laminated composite structures is the delamination between composite layers. In most engineering applications, laminated composite structures have certain curvatures. If the curved composite structure is subjected to bending that tends to flatten the composite structures, through the thickness stresses can be generated in the thickness direction of the composites. Under normal operation open mode delamination could occur at the sites of peak interlaminar stress. This paper describes a technique to determine radial direction stress of a laminated composite structure using a curved beam. Stacking sequence effects of interlaminar stress were studied. The radial location and intensity of the open mode delamination stress were calculated and compared with the results obtained from the analytical solution and finite element method.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.9
• /
• pp.1053-1057
• /
• 2012

In this study, the temperature-dependency of the tensile properties of a glass fiber reinforced plastic (GFRP) used in wind turbine blades was examined. The tensile strength, elastic modulus, and Poisson's ratio of the tensile specimen manufactured from uniaxial ($0^{\circ}$) and triaxial ($0/{\pm}45^{\circ}$) laminate composite plates were measured at four different testing temperatures-room temperature, $-30^{\circ}C$, $-50^{\circ}C$, and $60^{\circ}C$. It was found that the tensile strengths and elastic moduli of the uniaxial laminates were greater than those of the triaxial laminates over the testing temperature range. The tensile strength of the two laminates was significantly dependent on the testing temperature, while the dependency of the elastic modulus on the temperature was insignificant. Furthermore, it could be considered that the Poisson's ratio changed slightly with a change in the testing temperature.