• Journal of the Korean Recycled Construction Resources Institute
• /
• v.1 no.1
• /
• pp.17-25
• /
• 2013

Thermal storage technology used for indoor heating and cooling to maintain a constant temperature for a long period of time has an advantage of raising energy use efficiency. This, the phase changing material, which utilizes heat storage properties of the substances, capsulizes substances that melt at a constant temperature. This is applied to construction materials to block or save energy due to heat storage and heat protection during the process in which substances melt or freeze according to the indoor or outdoor temperature. The micro-encapsulation method is used to create thermal storage from phase changing material. This method can be broadly classified in 3 ways: chemical method, physical and chemical method and physical and mechanical method. In the physical and chemical method, a wet process using the micro-encapsulation process utilized. This process emulsifies the core material in a solvent then coats the monomer polymer on the wall of the emulsion to harden it. In this process, a surfactant is utilized to enhance the performance of the emulsion of the core material and the coating of the wall monomer. The performance of the micro-encapsulation, especially the coating thickness of the wall material and the uniformity of the coating, is largely dependent on the characteristics of the surfactant. This research compares the performance of the micro-capsules and heat storage for product according to molecular mass and concentration of the surfactant, SSMA (sulfonated styrene-maleic anhydride), when it comes to micro-encapsulation through interfacial polymerization, in which Dodecan-1 is transformed to melamin resin, a heat storage material using phase changing properties. In addition, the thickness of the micro-encapsulation wall material and residual melamine were reduced by adjusting the concentration of melamin resin microcapsules.

• Food Science and Preservation
• /
• v.22 no.6
• /
• pp.788-795
• /
• 2015

The efficacy of an experimentally designed cold chain container and a currently used styrofoam container was investigated with respect to important factors affecting the quality of fresh beef during storage under different conditions. The temperature in the TEPP-1 container was maintained at $5^{\circ}C$ using a phase change material (PCM) during transport and delivery. During storage in the TEPP-1 container, no significant difference was observed in pH of beef, but color decreased slightly, which does not affect the desire to purchase. After storage for 7 days, the rate of VBN and TBA in the TEPP-1 container, was lower than that in the TEPP-2 container. Drip loss was lower in the TEPP-1 container (0.87%) than in the TEPP-2 container (1.78%). No significant changes were observed in microbal count until 4 days in either of the containers, but after storage for 7 days, the count increased significantly. Microbial count in TEPP-1 was 6.65 log CFU/mL and that in TEPP-2 was 7.62 log CFU/mL. The results of sensory evaluations indicated that the overall acceptability of beef after storage for 7 days was better in the TEPP-1 container than in the TEPP-2 container. The EPS container was inferior in comparison with TEPP-1 and TEPP-2. It was impossible to continue the experiment using the EPS container after 3 days. These results suggest that the experimentally designed TEPP-1 container can be used for beef transport and delivery for 7 days without significantly affecting the quality of beef.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.6
• /
• pp.2596-2603
• /
• 2013

The precision and endurance of tire mold are very important factors to decide the quality of tire. However, the investigation on the thermal deformation of tire mold has a lot of trouble because the tire mold is produced in airtight permanent casting material. In this study, the thermal deformations such as temperature, displacement and stress distributions inside the AC7A tire mold casting material were analyzed by numerical analysis according to the preheating temperature of permanent casting device. In order to verify the results of numerical analysis, the experiments for temperature measurement of the AC7A casting material were carried out under the same condition with numerical analysis. For the numerical analysis, "COMSOL Multiphysics" was used. The preheating temperatures were set up $150^{\circ}C$, $200^{\circ}C$, $250^{\circ}C$ and $300^{\circ}C$, respectively. The thermal deformations were calculated in each case. When the preheating temperature is $300^{\circ}C$, displacement and stress are the lowest with 0.25mm and 0.351GPa, but the temperature is the highest with $374.27^{\circ}C$. When the experimental results were compared with the numerical results, there were some temperature differences because of the latent heat by phase change heat transfer. However, the cooling patterns were almost similar except for the latent heat section.

• Korean Chemical Engineering Research
• /
• v.55 no.1
• /
• pp.54-59
• /
• 2017

A study for process design to curtail the utility consumption during residual styrene monomer recovery in an ABS polymerization process was carried out. Among different techniques for residual monomer recovery, the steam stripping is dominantly employed in industries. The existing process, however, consumes a large amount of utility (steam and cooling water), and this study focused on the design of a new process that can substantially spare the utility consumption. A new process was configured to utilize the latent heat of the stripping steam, which is condensed with the monomer using cooling water after exiting the stripper. The condenser was modified to use vacuum state water as coolant and to generate vacuum state steam using the latent heat of the stripping steam. The steam is injected to the stripper as the stripping steam after upgrading using a compressor. Through this modification, consumption of steam and also cooling water could be significantly reduced at some expense of electricity for compressor operation.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.2
• /
• pp.952-962
• /
• 2015

In this study, multilayered rings with a large outer diameter have been developed using a hot ring rolling process. The ring rolling process has been analyzed by rigid plastic finite element analyses (FEA) using the AFDEX2D and AFDEX3D/HEXA/RING simulators, where the finite element meshes received severe plastic deformation are remeshed into a fine mesh-size using a dual-mesh system. According to the simulated results, the design variables of the multilayered rings were determined and real tests were conducted to check the validity of the simulation results. By adopting the hot ring rolling process, the input weight of raw materials was reduced by 40% against the conventional hot forging process and that the recovery rate was increased by 24%. The measurement of the averaged roundness was satisfied within 0.5 mm for both the inner and outer diameters. Moreover, the hot ring rolling processes yielded 1.49 Cpk for the outer-diameter and 0.84 Cpk 0.84 for the inner-diameter.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.9
• /
• pp.999-1005
• /
• 2011

The effects of strain-induced crystallization (SIC) on the mechanical properties of elastomeric composites as functions of extension ratio (${\lambda}$), multiwalled carbon nanotube (CNT) content, and carbon black (CB) content are investigated. The differential scanning calorimetry (DSC) analysis shows that the degree of crystallinity increases with the increase in the CB and CNT content. As ${\lambda}$ increases, the glass transition temperature (Tg) of the composites increases, and the latent heat of crystallization (LHc) of the composites is maximum at ${\lambda}$=1.5. It is found that the mechanical properties have a linear relation with LHc, depending on the CNT content. According to the TGA (thermogravimetric analysis), the weight loss of the composite matrix is 94.3% and the weight of the composites decreases with the filler content. The ratio of tensile modulus ($E_{comp}/E_{matrix}$) is higher than that of tensile strength (${\sigma}_{comp}/{\sigma}_{matrix}$) because of the CNT orientation inside the elastomeric composites.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2016.05a
• /
• pp.94-94
• /
• 2016

돌발홍수는 수십 $km^2$ 이하의 유역에서 강우가 발생한 후 6시간 이내의 단시간에 홍수징후가 나타나는 현상으로 정의될 수 있다. 돌발홍수를 잘 예측하기 위해서는 국지적으로 발생하는 집중 호우를 잘 예측해야 하며 유역내 공간적인 수문반응해석을 통해 돌발홍수를 예측하는 기술이 요구된다. 본 연구에서는 유역내 공간적인 수문반응을 잘 모의하기 위해 TOPLATS 지표해석모형을 이용하였다. TOPLATS(TOPMODEL based Land Atmosphere Transfer Scheme) 모형은 물수지와 에너지수지를 통해 단위격자에 대한 실제증발산량, 토양수분량, 지하수면깊이, 지표유출량, 잠열, 현열, 지열, 순복사량 등을 모의하며 소유역단위로 지하수면깊이를 재분포시키는 특성을 가지고 있다. 돌발홍수 위험도를 산정하기 위해 실제 돌발홍수 피해사례를 조사하였으며 피해지역과 대응되는 격자 수문성분과의 상관성 분석을 통해 돌발홍수 위험도 모형을 산정하였다. 대상지역은 수도권 전체지역을 모의하기 위해 한강, 임진강, 안성천 유역을 대상지역으로 선정하였다. 수도권 지역은 약 11,930 km2이며 2009~2012년동안 총 38건의 돌발홍수 피해사례가 신고되었다. 기상자료는 기상청 AWS와 ASOS 시단위 강우, 기온, 상대습도, 풍속, 일조, 기압자료를 이용하였다. 돌발홍수 피해사례 38건에 대해 대응되는 모의격자의 수문성분을 분석하였으며 27(71%)에서 구조요청시점에 대해 강우량, 지표유출량, 토양수분량, 지하수면깊이가 적절하게 모의되는 것을 확인하였다. 강우조건에 따른 돌발홍수 위험도는 구조요청시점 기준 선행시간 4~6시간까지 71~87%, 구조요청시점으로 한정된 0시간에서는 42~52%로 나타났다. 이상의 결과로부터 지표해석모델을 이용한 격자 수문성분과 통계적 돌발홍수지수모형으로부터 산정된 돌발홍수 위험도는 산지 미계측지역에 대한 돌발홍수를 예측하는데 활용될 수 있을 것으로 판단된다.

• Culinary science and hospitality research
• /
• v.20 no.3
• /
• pp.201-213
• /
• 2014

This study showed the quality characteristics of chicken breast meat(CB) and leg meat(CL) with various kinds of existing cooking methods and double layer pan filled with Phase Change Materials(PCM) heating. Steaming resulted the highest moisture contents of 63.9% and 62.1% each in CB and CL. Also, steaming showed the lowest with 1.3% and 8.6% of crude fat in CB and CL(p<0.05) respectively. Crude protein content of CB in charcoal heating and grilling of CL had the highest values of 37.9% and 30.5% each. In the test of crude ash, grilling showed the highest with 2.4% in CB(p<0.05) and oven heating and charcoal heating was the highest with 1.3% in CL(p<0.05). In the test of cooking loss, charcoal heating showed much higher with 33.52% and 41.16% in CB and CL each than the other cooking treatments. And in case of shear force test, $5.93kg/cm^2$ in CB and $6.80kg/cm^2$ in CL were the highest scores in grilling. In the test of color, L value of CB prepared by steaming showed the highest scores of 78.31(p<0.05) while CL by oven heating was the highest of 10.00 in a value. In the overall acceptability test of 9 point-scale sensory evaluation, CB prepared by charcoal heating showed the highest score of 7.25 points in boiling, but the lowest score of 6.00 points in steaming(p<0.05). CL by charcoal heating resulted the highest score of 7.71 points but had no significant difference.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.17 no.4
• /
• pp.384-398
• /
• 2015

In this paper, the high-resolution Weather Research and Forecasting/Noah-MultiParameterization (WRF/Noah-MP) modeling system is configured for the Cheongmicheon Farmland site in Korea (CFK), and its performance in land and atmospheric simulation is evaluated using the observed data at CFK during the 2014 special observation period (21 August-10 September). In order to explore the usefulness of turning on Noah-MP dynamic vegetation in midterm simulations of surface and atmospheric variables, two numerical experiments are conducted without dynamic vegetation and with dynamic vegetation (referred to as CTL and DVG experiments, respectively). The main results are as following. 1) CTL showed a tendency of overestimating daytime net shortwave radiation, thereby surface heat fluxes and Bowen ratio. The CTL experiment showed reasonable magnitudes and timing of air temperature at 2 m and 10 m; especially the small error in simulating minimum air temperature showed high potential for predicting frost and leaf wetness duration. The CTL experiment overestimated 10-m wind and precipitation, but the beginning and ending time of precipitation were well captured. 2) When the dynamic vegetation was turned on, the WRF/Noah-MP system showed more realistic values of leaf area index (LAI), net shortwave radiation, surface heat fluxes, Bowen ratio, air temperature, wind and precipitation. The DVG experiment, where LAI is a prognostic variable, produced larger LAI than CTL, and the larger LAI showed better agreement with the observed. The simulated Bowen ratio got closer to the observed ratio, indicating reasonable surface energy partition. The DVG experiment showed patterns similar to CTL, with differences for maximum air temperature. Both experiments showed faster rising of 10-m air temperature during the morning growth hours, presumably due to the rapid growth of daytime mixed layers in the Yonsei University (YSU) boundary layer scheme. The DVG experiment decreased errors in simulating 10-m wind and precipitation. 3) As horizontal resolution increases, the models did not show practical improvement in simulation performance for surface fluxes, air temperature, wind and precipitation, and required three-dimensional observation for more agricultural land spots as well as consistency in model topography and land cover data.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.18 no.4
• /
• pp.307-319
• /
• 2016

A Land-Atmosphere Modeling Package (LAMP) for supporting agricultural and forest management was developed at the National Center for AgroMeteorology (NCAM). The package is comprised of two components; one is the Weather Research and Forecasting modeling system (WRF) coupled with Noah-Multiparameterization options (Noah-MP) Land Surface Model (LSM) and the other is an offline one-dimensional LSM. The objective of this paper is to briefly describe the two components of the NCAM-LAMP and to evaluate their initial performance. The coupled WRF/Noah-MP system is configured with a parent domain over East Asia and three nested domains with a finest horizontal grid size of 810 m. The innermost domain covers two Gwangneung deciduous and coniferous KoFlux sites (GDK and GCK). The model is integrated for about 8 days with the initial and boundary conditions taken from the National Centers for Environmental Prediction (NCEP) Final Analysis (FNL) data. The verification variables are 2-m air temperature, 10-m wind, 2-m humidity, and surface precipitation for the WRF/Noah-MP coupled system. Skill scores are calculated for each domain and two dynamic vegetation options using the difference between the observed data from the Korea Meteorological Administration (KMA) and the simulated data from the WRF/Noah-MP coupled system. The accuracy of precipitation simulation is examined using a contingency table that is made up of the Probability of Detection (POD) and the Equitable Threat Score (ETS). The standalone LSM simulation is conducted for one year with the original settings and is compared with the KoFlux site observation for net radiation, sensible heat flux, latent heat flux, and soil moisture variables. According to results, the innermost domain (810 m resolution) among all domains showed the minimum root mean square error for 2-m air temperature, 10-m wind, and 2-m humidity. Turning on the dynamic vegetation had a tendency of reducing 10-m wind simulation errors in all domains. The first nested domain (7,290 m resolution) showed the highest precipitation score, but showed little advantage compared with using the dynamic vegetation. On the other hand, the offline one-dimensional Noah-MP LSM simulation captured the site observed pattern and magnitude of radiative fluxes and soil moisture, and it left room for further improvement through supplementing the model input of leaf area index and finding a proper combination of model physics.