• Proceedings of the KIEE Conference
• /
• 1995.11a
• /
• pp.593-595
• /
• 1995

X-Ray Diffraction method that gives direct information about the deformation of crystal lattice is used for the determination of profiles of the residual stress along the depth of heavily boron doped silicon. The residual stress distribution is obtained by XRD method as measuring the deformation of the front surface of the $p^+$ silicon layer fabricated through different etch time. It is determined that the compressive residual stress exists in the most region except the font surface.

• Journal of the Korean Vacuum Society
• /
• v.1 no.1
• /
• pp.145-152
• /
• 1992

Si surfaces exposed to CHF3/C2F6 gas plasmas ih reactive ion etching (RIE) have been characterized by X-ray photoelectron spectroscopy (XPS). CHF3/C2F6 gas plasma exposure of Si surface leads to the deposition of residual film containing carbon and fluorine. The narrow scan spectra of C 1s show various bonding states of carbon as C-Si, C-F/H, C-CFx(x $\leq$ 3), C-F, C-F2, and C-F3. The chemical bonding states of fluorine are described with F-Si, F-C and F-O. And the oxygen and silicon are also detected. The effects of parameters for reactive ion etching as CHF3/C2F6 gas ratio, RF power, and pressure are investigated.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.72-75
• /
• 1994

In this paper, a novel method to figure out the relative residual stress distribution along the depth of silicon diaphragms is presented Cantilevers with various thickness are fabricated by the time controlled etching method using EPW as an etchant. The boron concentration along the depth of the cantilevers is obtained by the TSUPREM IV simulation, and the etching time to get the proper thickness is calculated. By measuring deflections of the p+ silicon cantilevers the stress profile along the depth of diaphragm is calculated. The obtained stress profile is reasonable and useful to expect the deflection of cantilevers and the buckling of diaphragms.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.425-428
• /
• 2009

Silicone is recently used for LED chip encapsulment due to its good thermal stability and optical transmittance. To mold a solid-state silicone encapsulment, curing by mixing at elevated temperatures followed by cooling is necessary. As the silicone molding process is involved in healing and subsequent cooling, the thermal residual stress, which causes mechanical warpage or optical birefringence in the final silicone encapsulment, may be induced if there are non-uniformities in cured silicone material properties or encapsulment shape design. The prediction of residual stress is necessary to design a high-quality silicone molding process. Therefore, in the present paper, a numerical parametric study was attempted to evaluate the heating and cooling effects on the thermal residual stress induced in the cured silicone.

• Proceedings of the KIEE Conference
• /
• 1998.07g
• /
• pp.2524-2526
• /
• 1998

In this paper, the residual stress and young's modulus of the p+ thin film have been estimated by using the electrostatic resonators. The electrostatic plate resonator with four corrugated bridges and another with four flat ones have been fabricated. The deflection of the plate has been calculated under the induced tension and the residual stress and compared with the dynamic test results. When the young's modulus of the p+ silicon is 125 GPa. The estimated residual stresses of the flat and the corrugated bridges are about 15 MPa and less than 5 MPa, respectively. It has been confirmed that the corrugated structure releases the residual tensile stress resulted from the heavy boron diffusion process.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2008.11a
• /
• pp.81-82
• /
• 2008

하이브리드 코팅 시스템을 이용하여 $CrMoC_xN_{1-x}$ 박막을 AISI D2와 실리콘 웨이퍼 모재 위에 증착하였다. 박막 내 탄소 함량은 $CH_4/(CH_4+N_2)$ 가스 유량 증가에 비례하여 증가했다. 탄소 함량이 0.33일 때 44GPa의 최대강도 및 -4.4GPa의 잔류응력을 나타내었다. CrMoN 박막의 평균 마찰계수는 0.42이지만, 탄소함량을 증가함에 따라 0.31까지 감소 하였다. 이것은 박막 표면과 스틸볼 사이에서 탄소가 풍부한 층이 형성되어 일종의 고체윤활제 역할을 했기때문이다. 박막의 미세조직은 X-ray diffraction, Scanning electron microscopy, 그리고 X-ray photoelectron spectroscopy를 이용하여 분석하였다.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.9
• /
• pp.900-904
• /
• 2010

Polyvinyl chloride (PVC) hoses, polyethylene hose and silicone hose for tap water were tested with respect to migration of phenolic compounds to water. The highest concentrations (0.36~1.97 mg/L) of total phenolic compounds were observed in the test water from PVC hoses. Increasing residual Cl concentration from 0 to 0.5 mg/L or increasing water temperature from 4 to $25^{\circ}C$ increased 3~3.2 times and 100~104 times for migrated total phenolic compounds concentrations, in respectively. A major migrating phenolic compounds from PVC hoses were bisphenol-a (BPA) and it was observed that the concentration of migrating phenolic compounds in the order: DEHP > 2-chlorophenol > 2,4,6-trichlorophenol > 2,4-dichlorophenol from PVC hoses.

• Journal of Sensor Science and Technology
• /
• v.9 no.1
• /
• pp.1-8
• /
• 2000

One of today's very critical and sensitive accurate accelerometer which can be used higher temperature than $200^{\circ}C$ and corrosive environment, is particularly demanded for automotive engine. Because silicon is a material of large temperature dependent coefficient, and the piezoresistors are isolated with p-n junctions, and its leakage current increase with temperature, the performance of the silicon accelerometer degrades especially after $150^{\circ}C$. In this paper, The temperature characteristic of a accelerometer using silicon on insulator (SOI) structure is studied theoretically, and compared with experimental results. The temperature coefficients of sensitivity and offset voltage (TCS and TCO) are related to some factors such as thermal residual stress, and are expressed numerically. Thermal stress analysis of the accelerometer has also been carried out with the finite-element method(FEM) simulation program ANSYS. TCS of this accelerometer can be reduced to control the impurity concentration of piezoresistors, and TCO is related to factors such as process variation and thermal residual stress on the piezoresistors. In real packaging, The avarage thermal residual stress in the center support structure was estimated at around $3.7{\times}10^4Nm^{-2}^{\circ}C^{-1}$ at sensing resistor. The simulated ${\gamma}_{pT}$ of the center support structure was smaller than one-tenth as compared with that of the surrounding support structure.

• Journal of the Korean Vacuum Society
• /
• v.12 no.2
• /
• pp.144-149
• /
• 2003

Carbon tips were grown on Si cantilevers by applying an electron beam to them directly with Scanning Electron Microscope. A carbon tip was fabricated by aligning the electron beam directly down the vertical axis of Si cantilever and then irradiating a single spot on the cantilever for a proper time in the dominant atmosphere of residual gases generated by the oil of the diffusion pump. A number of control parameters for SEM, including exposure time, acceleration voltage, emission current, and beam probe current, were allowed to make various aspect ratio feature. The growth of carbon tips was not affected by the surface morphology of substrates. We could acquired the tip whose effective length is 0.5 $\mu\textrm{m}$, bottom diameter is 90 nm and cone half angle $3.5^{\circ}$ The growth technique of the high aspect ratio carbon tips on the tip-free cantilevers is available to reduce the complexities of fabricating sub-micron scale tips on the PZT thin film actuator integrated AFM cantilevers.

• Journal of the Korean Vacuum Society
• /
• v.13 no.3
• /
• pp.120-126
• /
• 2004

A damage-reduced trench was investigated in view of the defect distribution along trench sidewall and bottom using high resolution transmission electron microscopy, which was formed by HBr plasma and additive gases in magnetically enhanced reactive ion etching system. Adding $O_2$ and other additive gases into HBr plasma makes it possible to eliminate sidewall undercut and lower surface roughness by forming the passivation layer of lateral etching. To reduce the RIE induced damage and obtain the fine shape trench corner rounding, we investigated the hydrogen annealing effect after trench formation. Silicon atomic migration on trench surfaces using high temperature hydrogen annealing was observed with atomic scale view. Migrated atoms on crystal surfaces formed specific crystal planes such as (111), (113) low index planes, instead of fully rounded comers to reduce the overall surface energy. We could observe the buildup of migrated atoms against the oxide mask, which originated from the surface migration of silicon atoms. Using this hydrogen annealing, more uniform thermal oxide could be grown on trench surfaces, suitable for the improvement of oxide breakdown.