• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.22 no.6
• /
• pp.415-422
• /
• 2010

Development of the reliability-based design program in the GUI environment is inadequate for engineers familiar with the deterministic design to deal with the international design criterion based on the probabilistic design. In this study, the design program based on the GUI environment is developed in order to more efficiently input the design factor and more easily carry out the design works. The GUI environment is the GUIDE (Graphic User Interface Development Environment) tool supported by the latest MATALB version 7.1. In order to test the model reliability, the probabilities of failure (POF) on the breakwater armor block (AB) and gravity quay-wall (QW) in the sliding mode are computed using the model in the Level II and Level III. The POF are 55.4~55.7% for breakwater AB and 0.0006~0.0007% for gravity QW. A non-GUI environment program results of the POF are 55.6% for breakwater AB and 0.0018% for gravity QW. In comparison, the POF difference is negligible for breakwater AB because the exact input design parameters are available, whereas the large POF difference, but within the same order, for gravity QW can be explained by the difference of the input design factors because of the poor input data information.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.26 no.2
• /
• pp.147-156
• /
• 1981

Most of the currently available rice threshers in Korea are of head-feeding type originally developed for threshing paddy at grain moisture content of 15 to 17% on wet basis. And prevailing rice harvesting system is swathing or cutting and bundling upright rice crop at a maturity stage of grain moisture content of ca. 28 to 20%, followed by transient natural drying in the field and threshing at grain moisture content of about 17%. The system often allows rather high field loss of rice both quantitatively and qualitatively. These necessitate use of a preharvest desiccant, and diquat has been registered recently as a rice desiccant. Aim of the present study is to determine the best time and rate of diquat application and to evaluate its utility as a rice desiccant under its optimal usage conditions in Korea. Diquat was not so effective for japonica rice varieties while it was very effective for the new varieties bred from indica x japonica crosses. The best time of application was the period from 2 days before to 3 days after physiological maturity of grain (moisture content of 28% w.b.) and the optimal rate was about 330g of diquat ion/ha. Applying diquat at the right time and rate dropped grain moisture to 15 to 16% (w.b.) within a week after treatment in contrast to that of 20 to 24% in untreated rice. Desiccation of rice crop with diquat resulted in 10 to 15% increase in grain resistance to shattering and significant reduction in percent green rice. However, there was no reduction in milled rice yield and percent whole kernel and was no change in the percent chalky rice and percent tinted rice. Diquat use appears highly desirable, if there is no residue problem which has not been studied in the present study.

• Cartoon and Animation Studies
• /
• s.36
• /
• pp.167-187
• /
• 2014

Animation-related films and game industries have been expanding their markets rapidly responding to sharply increasing public demand. The production processes of major studios are getting more and more specialized and detailed. Therefore, they feel burden to manage and maintain as the HR and physical sizes are getting greater. So, independent studios which perform partial processes of the works are increasing over North America and Europe. Specialized studios build previous functions and related business models. They are expanding their areas. Therefore, this study targeted studios specialized in digital concept art in free production step. The characteristics of such studios were analyzed. To this end, first definitions of digital concept art concepts and functional & artistic features of entire production, and their application to business were deliberated through documents and online. Based on the results, the features of 'concept art service', 'self-brand business/ communication', and 'education service' were drawn. Second, based on it, targeting three con cept art studios such as Atomhawk (UK), FengZhu Design (Singapore), and Studio Gage (Korea), case research was done. Comparative analysis for the cases was conducted. It turned out that concept art studio s lead new market demand through active business strategies such as related contents development, marketing, etc. based on specialization. This research is significant to understand global trend of newly establishing specialized studios market and suggest reference data to improve prospective domestic specialized studios competitiveness.

• Economic and Environmental Geology
• /
• v.43 no.6
• /
• pp.615-623
• /
• 2010

Seismic refraction survey is a geophysical method that delineates subsurface velocity structure using direct wave and critically refracted wave. The generalized reciprocal method(GRM) is an inversion technique which uses travel-time data from several forward and reverse shots and which can provide the geometry of irregular inclined refractors and structures underlain by hidden layer such as low velocity zone and thin layer. In this study, a simple Excel-GRM routine was tested for fast mapping of the interface between weathering layer and bedrock during the survey, with employing a pair of forward and reverse shots. This routine was proved to control the maximum dip of approximately $30^{\circ}C$ and maximum velocity contrast of 0.6, based on the panel tests in terms of dipping angle and velocity contrast for the two-layer inclined models. In contrast with conventional operation of five to seven shots with sufficient offset distance and indoor data analysis thereafter, this routine was performed in the field shortly after data acquisition. Depth to the bedrock provided by Excel-GRM, during the field survey for Cheongju granite area, correlates well with the elevation of the surface of soft rock from the drill core and SPS logging data. This cost-effective routine developed for quickly delineating the bedrock surface in the field survey will be readily applicable to mapping of weathering zone in narrow zone with small variation of elevation of bedrock.

• Analytical Science and Technology
• /
• v.17 no.4
• /
• pp.355-362
• /
• 2004

Fission products and Inter reaction layer of $U_3Si-Al$ dispersion fuel, irradiated in HANARO research reactor with 121 kW/m of maximum liner power and 63 at% of average burn-up, was characterization by EPMA (Electron Probe Micro Analyzer). The fuel punching system developed by Irradiated Materials Examination Facility (IMEF) has used to make these samples for the EPMA. With this system a very small and thin specimen which is 1.57 mm in diameter and 2 mm in thickness respectively has been fabricated to protect the EPMA operator from high radioactive fuel and to mini-mize the equivalent dose rate less than 150 mSv/h. EPMA was performed to observe layers of sectional, Inter-reaction and oxide with specimens of cutting and polished. Stoichiometry in the Inter-reaction layer with $16{\mu}m$ of thickness was $U_{2.84}$ Si $Al_{14}$ with calibration of $UO_2$ and $U_{3.24}$ Si $Al_{14.1}$ with calibration of standard specimen. metallic precipitates in this layer were not observed using fission products examination.

• Journal of Broadcast Engineering
• /
• v.6 no.3
• /
• pp.246-259
• /
• 2001

Due to recent rapid deployment of Internet streaming service and digital broadcasting service, the issue of how to efficiently support streaming workload in so called "Internet Home Appliance" receives prime interests from industry as well as academia. The underlying dilemma is that it may not be feasible to put cutting edge CPU, boards, disks and other peripherals into that type of device. The primary reason is its cost. Usually, Internet Home Appliances has its dedicated usage, e.g. Internet Radio, and thus it does not require high-end CPU nor high-end Va subsystem. The same reasoning applies to I/O subsystem. In Internet Home Appliances dedicated to handle compressed moving picture, it is not equipped with high end SCSI disk with fast rotational speed. Thus, it is mandatory to devise elaborate software algorithm to exploit the available hardware resources and maximize the efficiency of the system. This paper presents our experiences in the design and implementation of a new multimedia file system which can efficiently deliver the required disk bandwidth for a periodic I/O workload. We have implemented the file system on the Linux operating system, and examined itsperformance under streaming I/O workload. The results of the study show that the proposed file system exhibits superior performance than the Linux Ext2 file system under streaming I/O workload. The result of this work not only contribute to advance the state f art file system technology for multimedia streaming but also put forth the software which is readily available and can be deployed. deployed.

• Journal of the Society of Disaster Information
• /
• v.15 no.4
• /
• pp.524-530
• /
• 2019

Purpose: In this paper, we construct a detailed three-dimensional interface element using a three-dimensional analysis program, and evaluate the composite behavior stability of the connector by applying physical properties such as the characteristics of general members and those of reinforced members Method: The analytical model uses solid elements, including non-linear material behavior, to complete the modeling of beam structures, circular flanges, bolting systems, etc. to the same dimensions as the design drawing, with each member assembled into one composite behavior linkage. In order to more effectively control the uniformity and mesh generation of other element type contact surfaces, the partitioning was performed. Modeled with 50 carbon steel materials. Results: It shows the displacement, deformation, and stress state of each load stage by the contact adjoining part, load loading part, fixed end part, and vulnerable anticipated part by member, and after displacement, deformation, The effect of the stress distribution was verified and the validity of the design was verified. Conclusion: Therefore, if the design support of the micro pile is determined based on this result, it is possible to identify the Vulnerable Parts of the composite behavior connector and the degree of reinforcement.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.14 no.2
• /
• pp.53-62
• /
• 2012

Demand for high resolution weather data grows in the agriculture and forestry fields. Local Analysis and Prediction System (LAPS) can be used to analyze the local weather at high spatial and temporal resolution, utilizing the data from various sources including numerical weather prediction models, wind or temperature profilers, Automated Weather Station (AWS) networks, radars, and satellites. LAPS has been set to analyze weather elements such as air temperature, relative humidity, wind speed, and wind direction every hour at the spatial resolution of $100m{\times}100m$ for Gyeonggi-do on near real-time basis. The AWS data were revised by adding the agricultural field AWS data (33 stations) in addition to the KMA data. The analysis periods were from 1 to 31 August 2009 and from 15 to 21 February 2010. The comparison of the LAPS output showed the smaller errors when using the agricultural AWS observation data together with the KMA data as its input data than using only either the agricultural or KMA AWS data. The accuracy of the current system needs improvement by further optimization of analyzing options of the system. However, the system is highly applicable to various fields in agriculture and forestry because it can provide site specific data with reasonable time intervals.

• 대한공업교육학회지
• /
• v.31 no.2
• /
• pp.307-331
• /
• 2006

The purpose of this study is to find out what the constituents of career development competency are for the students who are majoring in engineering. In this study, the career development competency means that the students in an engineering college should initiatively choose, prepare and adapt themselves for their future career in their lifetime. This study examined all the career-related references that are determined to be linked with the competencies of career development. Also, other references inside and outside of the country that are related to the career key competencies and engineering basic competencies were investigated in this study. Especially, the career development competency in this study was approached with two points of views; the process of career development for students and the ability to maintain and develop the future career in an engineering field. Ultimately, this study derived the conclusion that there are 8 categories and 42 subordinate constituents in the career development competency for the students in an engineering college.

• 대한공업교육학회지
• /
• v.33 no.1
• /
• pp.169-190
• /
• 2008

The purposes of this research were to review the validity and to investigated educational needs of the establishment for invention gifted school. And this study was conducted on the establishment plan through diagnosis necessity and validity of the establishment for invention gifted school. The methodes of this study were review, investigation researches, workshop, expert review for validity and a seminar. The results was as follows: First, the invention gifted school presented distinctive curriculum and instruction methods. The curriculum focus on engineering, technology, invention, problem solving, and STEM. And it presented scenario on the establishment of invention gifted school from the viewpoint of necessity and distinction. Second, the invention gifted school investigated high-level transition from demand of education of students and their parents. Third, the necessity level was higher than the validity and feasibility with expert assessment. But, before the establishment of the invention gifted school institute will review pre-requirements and hinder factors.