• The Journal of the Korea institute of electronic communication sciences
• /
• v.6 no.2
• /
• pp.180-185
• /
• 2011

The TPMS(Tire Pressure Monitoring System) is an electronic system designed to display the air pressure inside the pneumatic tires and report real-time tire-pressure information to the driver of the vehicle, either via a gange, a pictogram display, or a simple low-pressure warning light. Although the data measured by TPMS sensor is transmitted to internal signal processer in a vehicle through wireless communication, the receiver may suffers from various interferences such as amateur radio station, RFID(Radio-Frequency IDentification) for controlling container, RKE(Remote Keyless Entry) signal, and so on. In this paper, we consider beamforming technology to suppress various high-power interference signals for the TPMS wireless communications. Also, we propose the proper data structure and antenna arrangement for the beamformer inside the vehicle. The performance for the interference suppression is illustrated by computer simulation example.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.2
• /
• pp.125-130
• /
• 2013

According to the law revision of TPMS mounting obligations in Korea, researches about energy harvester which is the alternative of the battery are actively performed by many groups. Because WSN (Wireless Sensor Network) has the proposition of "Install and forget" and the power supplier also has the same performance as the vehicle's lifetime. In this paper, electromagnetic induction type of energy harvester through the relative motion between the rotating wheel and the fixed brake disc is introduced by using the most efficient source as the rotating motion in the view of vehicle's mechanism. The coil on the wheel and the permanent magnet at the brake disc are arranged in several ways. These various arrangements are the number of coil turns are consisted of design variables. By using the orthogonal array to reduce the experimental cost, the optimal composition is verified through the experiment. Finally the validity of the module is considered by measuring the level of storable electrical energy.

• International Journal of Highway Engineering
• /
• v.14 no.1
• /
• pp.25-34
• /
• 2012

The rapid economic development induced the massive road constructions, becoming bigger and high-speed of the vehicles. However, it brings lots of social problems, such as air pollutions, traffic noise and vibration. Special concrete block for the base course of asphalt pavement is needed to decrease traffic noise such as tire's explosive and vehicles sound, applying Helmholtz Resonators theory to asphalt pavement. If it is applied to the area where it happens considerable noise such as a junction, the street of a housing complex and a residential street, it is one of alternative methods to solve the social requirements of noise problems. This research examines couple of laboratory tests for the sound absorption effect of the concrete block and the base concrete block for quiet pavement. The specimens, which is fixed hall-size, space, depth as the condition of this research, are analysed of noise reduction effect using different noise levels of vehicles. Judging from the analysis of test results with vehicle noise volume, measurement distance, a form and size of the hall using the base concrete block, the use of special concrete base and quiet asphalt surface showed a good alternative solution for decreasing traffic noise level, from 4dB to 9dB.

• Elastomers and Composites
• /
• v.48 no.2
• /
• pp.125-132
• /
• 2013

In this work, we have discussed new engineering systems for preparing carbon master batch composed by carbon black and various organic compounds. In general, polymer resin, which applied for automobile tire, household items, and various industry items, is used with the fillers including carbon black and silica to control the color or properties. Domestic part and material industry has been remarkably developed in that the development of materials including the compounding of raw materials. Meanwhile, the engineering technique for mass production has not reached to a requirement of industry due to slow technique development and high dependence on foreign. Thus, we will focus on the introduction of new engineering technique developed by domestic company for preparing carbon master batch.

• Elastomers and Composites
• /
• v.47 no.2
• /
• pp.121-128
• /
• 2012

Waste EPDM(W-EPDM) collected from the automotive weather strip and the gasket of a laundry machine has not been effectively recycled. Using this W-EPDM powder and other ingredients, i.e., binder(polyolefin resin, polyolefin elastomer, etc.), filler and additives, various economic rubber composites were made by extrusion. In advance of main experiments, the effects of ultrasonic treatment of W-EPDM on the property of rubber composites, comparison in the property of the composites of W-EPDM with those of virgin and devulcanized EPDM, and waste tire rubber were investigated. Also, the properties of the rubber composites extruded with a 12-screw extruder were compared with those extruded with twin-screw extruder. Various W-EPDM composites for synthetic turf filler and car mat were extruded and injection molded, and 3 main properties of tensile strength, elongation and hardness were investigated to develop economical and proper recipes of the rubber composites.

• Korean Journal of Agricultural Science
• /
• v.32 no.1
• /
• pp.1-8
• /
• 2005

This study was carried out to examine the effect of heavy traffic on chemical properties of soil in roadside trees of Daejeon city. Soil samples at 0~10cm and 10~30cm depths were collected from soil of the roadside trees, Platanus occidentalis, and Ginko biloba, Soil pH in heavy traffic regions were around 7.0 at 0~10cm and 10~30cm soil depths because of spraying of calcium chloride for snow moving. The concentrations of Fe, Cd, Cu, Zn, and Pb in soil were higher in heavy traffic regions(Daejeon Station and Daehwa Industrial Complex) than in light traffic region (Chungnam National University). The result could be from rubbing and wear of car tire and metals when they travel.

• Journal of the Korea Convergence Society
• /
• v.3 no.4
• /
• pp.35-44
• /
• 2012

In this study, a simulation program is developed in order to investigate non steady-state cornering performance of 6WD/6WS special-purpose vehicles. 6WD vehicles are believed to have good performance on off-the-road maneuvering and to have fail-safe capabilities. But the cornering performances of 6WS vehicles are not well understood in the related literature. In this paper, 6WD/6WS vehicles are modeled as a 18 DOF system which includes non-linear vehicle dynamics, tire models, and kinematic effects. Then the vehicle model is constructed into a simulation program using the MATLAB/SIMULINK so that input/output and vehicle parameters can be changed easily with the modulated approach. Cornering performance of the 6WS vehicle is analyzed for brake steering and pivoting, respectively. Simulation results show that cornering performance depends on the middle-wheel steering as well as front/rear wheel steering. In addition, a new 6WS control law is proposed in order to minimize the sideslip angle. Lane change simulation results demonstrate the advantage of 6WS vehicles with the proposed control law.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.3
• /
• pp.697-705
• /
• 2014

This paper presents a vision based object width measurement method and its application where the light sectioning method is employed. The target object for measurement is a tread, which is the most outside component of an automobile tire. The entire system applying the measurement method consists of two processes, i.e. a calibration process and a detection process. The calibration process is to identify the relationships between a camera plane and a laser plane, and to estimate a camera lens distortion parameters. As the process requires a test pattern, namely a jig, which is elaborately manufactured. In the detection process, first of all, the region that a laser light illuminates is extracted by applying an adaptive thresholding technique where the distribution of the pixel brightness is considered to decide the optimal threshold. Then, a thinning algorithm is applied to the region so that the ends and the shoulders of a tread are detected. Finally, the tread width and the shoulder width are computed using the homography and the distortion coefficients obtained by the calibration process.

• Journal of the Korea Convergence Society
• /
• v.10 no.11
• /
• pp.79-84
• /
• 2019

Video image based technology is being used in various fields with continuous development. The demand for vision system technology that analyzes and discriminates image objects acquired through cameras is rapidly increasing. Image processing is one of the core technologies of vision systems, and is used for defect inspection in the semiconductor manufacturing field, object recognition inspection such as the number of tire surfaces and symbols. In addition, research into license plate recognition is ongoing, and it is necessary to recognize objects quickly and accurately. In this paper, propose a recognition model through the rotational alignment of objects after checking the angle value of the tilt of the object in the input video image for the recognition of inclined objects such as numbers or symbols marked on the surface. The proposed model can perform object recognition of the rotationally sorted image after extracting the object region and calculating the angle of the object based on the contour algorithm. The proposed model extracts the object region based on the contour algorithm, calculates the angle of the object, and then performs object recognition on the rotationally aligned image. In future research, it is necessary to study template matching through machine learning.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.11
• /
• pp.521-528
• /
• 2018

Military vehicles use run-flat wheels for emergency situations. Run-flat wheels can run required distance in a defined duration with the pressure loss tire. For the application of a run-flat system, wheels are designed in 2 pieces, including an inner rim and outer rim. These rims are assembled using clamping bolts. Clamping bolts determine the durability of military vehicle wheels because fracture of clamping bolts account for most wheel failures. For improving wheel durability, clamping bolt durability must be improved. In this study, wheel test conditions and bolt design were investigated. Existing test standards are not sufficient to conduct endurance tests. Supplementary conditions were investigated. Using these modified test conditions, the durability of wheels including clamping bolts was tested and verified. Results found the durability of wheels improved more than 168%. This study also proposes improvements in the design process of clamping bolts.