• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.3
• /
• pp.295-302
• /
• 2013

The two cross-roll straightening process at room temperature is a manufacturing method for improving the straightness of a drawn wire. The distribution and magnitude of the internal and surface residual stresses of the drawn wire are changed after the wire-drawing process through the two cross-rolls; this also results in a change in the diameter of the drawn wire. The remaining residual stresses of the drawn wire after the wire-drawing dimensional changes were analyzed according to the distance between the rolls, oblique angle between the axes of the roll and the wire, predicted residual stresses, and dimensional change in the final product. The oblique angle between the concave and convex rolls did not affect the residual stresses or dimensional change, but the distance between rolls did.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.7
• /
• pp.723-730
• /
• 2012

During the cold wire-drawing process, the diameter of a wire is reduced and the length of the wire is increased as the wire passes through the die. The pressure and sliding motion at the interface between the wire and die cause elastic recovery of the workpiece and friction and wear on the die. In addition, wire deformation and frictional heating raise the temperature of the wire and die, resulting in difficulty in manufacturing the drawn products according to a designated inner diameter of the die, deviating from the designated dimension or the inner diameter of the die. In this study, considering the die temperature distribution, the effects of dimensional changes of the drawn products were analyzed quantitatively; these changes are caused by the elastic deformation of the die, the elastic recovery of the workpiece, and the thermal deformation of both the die and the workpiece. It was confirmed that the elastic recovery of the workpiece influenced these changes the most. The initial dies considering these factors could avoid deviation from the designated dimension, and the desired drawn products were obtained by using the designed initial drawing dies.

• Proceedings of the Korea Crystallographic Association Conference
• /
• 2003.05a
• /
• pp.24-24
• /
• 2003

고온초전도 BSCCO 2223 ((Bi, Pb)₂Sr₂Ca₂Cu₃O/sub x/) 선재의 특성을 향상시키기 위해서는 반복적인 인발 및 압연과정을 통한 texturing향상, BSCCO 2223입자의 배향성 증대, 피복재내 초전도체의 충진율(밀도)향상, 이차상의 부피분율 감소등이 이루어져야 한다. 최적 열처리 조건을 통하여 열처리 시에 형성되는 이차상인 (Bi,Pb)₂Sr₂CuO/sub y/ (2201, amorphous phase)를 조절하면서, (Ca,Sr)₂CuO₃ (2/1 AEC), (Ca,Sr)/sub 14/Cu/sub 24/O/sub 41/ (14/24 AEC)와 같은 이차상들의 부피분율 및 크기를 감소시켜야만 한다. 본 실험에서는 BSCCO 2223 선재의 특성을 향상시킬수 있는 최적의 열처리 조건 확립 및 기계적 공정시 나타나는 여러 가지 문제점을 개선하여 높은 임계전류를 가지는 선재의 특성을 분석하고자 하였다. 최종적으로 제조된 선재는 2223상 결정이 피복재(Ag)와 평행하게 길게 성장하며, AEC상의 크기와 부피분율이 감소할수록 더 높은 임계전류특성을 나타내었다(I/sub c/～70A, J/sub c/～42,000 A/㎠). 또한 이 선재에서 나타나는 여러 가지 이차상들을 분석하기 위하여 XRD, SEM, EDS 분석을 행하였다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.834-837
• /
• 2005

This study presents a study on the influence of process parameters(semi-die angle, die reduction, friction condition, and bearing length) in drawn wire on residual stresses were investigated using FE-analysis. In this study, semi-die angle and die reduction have a significant effect on the residual stresses at the surface of drawn wire. In the previous study, in order to reduce the residual stresses, several methods were suggested: addition of axial tension, application of skin pass, straightening in multi-roll straightener etc. In this study, it can be known that the concurrent application of skin pass with low die reduction and low semi-die angle at the final stage of drawing operation reduces dramatically the both axial and hoop residual stresses after drawing.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.821-825
• /
• 2000

Drawing is one of the oldest metal forming operations and has major industrial significance. This process allows excellent surface finishes and closely controlled dimensions to be obtained in long products that have constant cross sections. In drawing of the high carbon steel wire, exit speeds of several hundreds meters per minute are very common. Drawing is usually conducted at room temperature using a number of passes or reductions through consequently located dies. In multi-stage drawing process like this, temperature rise in each pass affects the mechanical properties of final product such as bend, twist and tensile strength. In this paper, therefore, to estimate the wire temperature in multi-stage wire drawing process, wire temperature prediction method was mathematically proposed. Using this method, temperature rise at deformation zone as well as temperature drop between die exit and the next die inlet were calculated.

• Electrical & Electronic Materials
• /
• v.6 no.5
• /
• pp.407-416
• /
• 1993

무산소동을 안정화 모재로한 Cu/Nb-Ti 빌렛트를 제작한 다음 간접 열간방식의 압출에 의해 얻어진 봉재를 인발한 후 신선과 열처리를 반복하여 단심 및 다심 Nb-Ti 초전도 선재를 제조하였다. 가공 조직을 조사한 결과, 단심 선재의 경우 Nb-Ti 심의 단면이 균일하게 가공된 것을 확인하였으며 다심선재의 경우는 신선가공에 의하여 다소 불균질한 필라멘트부분이 관찰되었다. 4.2K, 자장하에서 4단자법으로 직선형 단척시료의 임계전류를 측정하여 가공 열처리 조건에 따른 임계전류밀도의 자장특성을 조사하였는데 열처리시간을 길게하고 가공도를 높인 시료일수록 자장하의 임계전류밀도가 높게 나타나는 것을 확인하였다. 4.2K, 5T 자장하에서 각각 4 x $10^{5}$A/$cm^{2}$ 및 2 x $10^{5}$A/$cm^{2}$의 임계전류밀도를 나타내는 Nb-Ti 단심 및 다심 초전도선재를 제작 할 수 있었다.있었다.

• Journal of the Korean Professional Engineers Association
• /
• v.31 no.1
• /
• pp.74-84
• /
• 1998

본 지도업체인 쌍희금속은 1988년 2월 설립, 주생산제품은 닉켈합금선으로서 1997년 12월 현재 총매출액 7.4억원(수출 0.12억 포함) 당기순이익 0.32억원으로 종업원 9명을 포함한 개인기업 형태로 특히 총매출액의 6%를 기술투자비율에 할당하고 있는 유망 중소기업이다. 기술지도와 관련한 연선의 선재(線材)는 포항제철의 $^{ø}$8mm 태선(允線)이 주종이나 특수선(特殊線)인 경우는, 국내선재의 경우 멜팅(Melting)기술이 부족하여 독일국으로부터 $^{ø}$5.5 mm의 선재를 직수입에 의존하고 있었다. 한편 세선가공의 선재는 20여개의 Dies공구 가공공정을 통한 $^{ø}$1.3 mm의 선채를 사용하여 $^{ø}$0.6 mm의 세선(細線)을 가공하고 있었다. 그러나 인발(引拔) 기술과 관련함에 특히 Dies 공구로부터 세선(細線)을 제조한 후 마무리 공정에서의 탈지문제가 정립돼있지 못하여 End User로부터 불만사례가 종종 야기 되었다 이의 원인 규명을 기술지도를 통해 조사한 결과 소성가공유(습식형)의 인식 부족이 주원인이였다. 소성가공유의 조성은 일반적으로 식물성. 광물성, 계면활성제, 극압제 등으로 구성됨에 마무리공정에서의 탈지방법은 가공유제의 기재(Base oil)에 따라 다르다 즉 기유(基油)가 광물계인 경우는 탈지제가 용제형(TCE 등)이 양호하나 식물계인 경우는 Alkali계가 양호하다. 따라서 NaOH sol'n2~3%+분산제(기포방지제)로서 음이온인 노닐페놀 0.1~0.3%의 처방을 제시하고 설비로서는 8$0^{\circ}C$로 유지되는 조제된 알칼리 Vessel과 물중탕 설비(열풍설비 포함)등을 대입하는 공정개선으로 Dies를 통과한 중간제품의 세선 $\longrightarrow$ 탈지설비 $\longrightarrow$ 80～85$^{\circ}C$로 유지되는 열처리(Aniling)공정을 대입함에 세선의 가공경화가 없었으며 아울러 수용성 가공유의 관리 한계(사내표준화)를 설정 관리 하도록 지도함으로서 지도 전에 비해 제조원가의 절하 및 생산성 향상은 물론 세선의 신규 탈지제 개발과 공정 개선을 통하여 가열공정의 부하개선 과 최종제품인 절연선의 품질향상을 가져 왔다.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.9
• /
• pp.100-105
• /
• 2019

In wire drawing, aterial deformation is concentrated on the surface of the drawn wire because of surface contact with the drawing die. Therefore, strain varies from the center to the surface of the drawn wire. In this study, based on the upper bound method, an effective strain prediction method from the center to the surface of a drawn wire was proposed. Using the proposed method, the effective strain of the drawn wire was calculated verify the proposed prediction method, the predicted effective strain was compared with the result of finite element analysis.

• Journal of Korean Association for Spatial Structures
• /
• v.7 no.1 s.23
• /
• pp.71-78
• /
• 2007

Stainless steel is very famous for using of industrials structure and joint elements. Stainless steel wire drawing is one of the most ancient crafts. But there's not any standard size of tapered die during tile drawing. This paper was studied die angle and dimension of whole die by using AFDEX drawing simulator. Stress, metal flow and strain rate was analyzed by AFDEX tools during the wire drawing. So optimum data of during dies was taken from them. Simulation data was correspond with experimental data. The results of the optimum dies are shown that (1) Reduction angle is $13.8^{\circ}$ (2) Bark relief angle is $20^{\circ}$ (3) Bearing length is 0.7975mm (4) Bearing dia is 0.2393mm The research of the optimum result when the make dies is connected an enterprise. After researching, I hope that indirection effect creation make development situation of the manufactural technical, practical application of the other die size by the detail data, utility factor and economical efficiency.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.89-92
• /
• 2004

This paper is concerned with the drawing process of Al-Si wire. In this study, the finite-element model established in previous work was used to analyze the effects of various forming parameters, which included the reduction in area, the semi-die angle, the aspect ratio and the inter-particle spacing of the Si in drawing processes. The finite-element results gave the consolidation condition. From the results of analysis, the effects of each forming parameter were determined. It is possible to obtain the important basic data which can be guaranteed in the fracture prevention of Al-Si wire by using FEM simulation.