• Journal of the Korean GEO-environmental Society
• /
• v.4 no.1
• /
• pp.67-75
• /
• 2003

In this study, the steel strip reinforcement bolted with braced angles expected to mobilize skin friction resistance as well as bearing resistance is proposed. Laboratory pullout tests are conducted to investigate the characteristics of pullout behavior. From the test results, friction effects between soil and reinforcement are evaluated with the width of reinforcement, magnitude of surcharge, and existence of bearing resistance member. Further to analyze interference effects for bearing resistance member, pullout tests are also carried by varing the number, the location, and the spacing of braced angles. Based on the test results, pullout resistance factor is evaluated under the consideration of location of braced angles and the degree of interference for spacing ratio.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2011.05a
• /
• pp.319-324
• /
• 2011

최근 자연환경보전이라는 새로운 패러다임의 대두로 하천의 생태기능 향상을 위한 호안조성공법 중 하나인 식생매트호안 공법의 적용이 증가하고 있다. 국내 하천의 경우 비교적 큰 하상계수와 소류력의 증가로 식생매트 고정용 앵커핀의 기능 저하에 따른 호안의 피해가 발생하고 있다. 그러나 앵커핀의 외력저항성 연구 및 설치를 위한 기준이 마련되어 있지 않는 실정이다. 본 연구에서는 앵커핀의 인발특성을 연구함으로서 외력저항 특성을 파악하고자 하였다. 연구방법으로는 앵커핀을 관입시킨 토사에 인발장치를 연결하여 최대인발력과 인발력의 변화추이를 관찰하였다. 실험에 사용된 토사는 물다짐으로 다졌으며, 앵커핀은 식생매트 고정용으로 적용이 많은 이형철근형 앵커핀을 사용하였다. 대조군으로 형태가 동일한 원형철근을 이용하여 앵커핀을 제작 실험에 사용하였다. 실험조건은 앵커핀의 직경(10mm, 16mm)에 따른 주면과 침수토사의 배수시간 (48hr, 96hr, 144hr) 조절을 통한 함수율의 변화에 따른 인발특성을 관측하였다. 실험결과 평균 최대인발력의 변화는 48시간 배수시 직경변화에 따라 이형철근은 12.8N, 28N, 원형철근은 10.6N, 21N으로 나타났으며, 96시간 배수시 이형철근은 18.8N, 33N, 원형철근은 12.2N, 21.6N으로 나타났고, 144시간 배수시 이형철근은 21.4N, 36.4N, 원형철근은 20.4N, 33.2N으로 나타났다. 앵커핀의 인발력은 주면의 크기에 비례하며, 표면의 형태와 함수량에 따라 영향을 받는 것으로 나타났다. 따라서 이러한 앵커핀의 인발 특성을 파악하고, 식생호안에 적용한다면 피해를 최소화 할 수 있을 것으로 사료된다.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.5
• /
• pp.49-55
• /
• 2017

In the seventies, a number of researchers carried out experiments on pullout tests with prototype equipment, and the pullout test was certified as a reliable nondestructive testing(NDT) method for determining the strength of concrete. To estimate the strength of high-strength concrete, we propose a simplified pullout test that uses as a break-off bolt a standard 10mm bolt with a groove on the shaft, an insert nut, and a pullout instrument that includes a hydraulic oil pump without a load cell. To verify the advantages of the simplified pullout test(low cost, simplicity, and convenience), four wall specimens were tested with two levels of concrete strength, 30 MPa and 50 MPa, using a simplified pullout tester with a load cell. The pullout load and concrete compressive strength were measured every day until day 7, day 14, day 21 and day 28. It was found that the pullout load was very similar to the compressive strength. Therefore, we have verified that a simplified pullout test can be used to evaluate the in-place strength of high-strength concrete in structures. The prediction equation of the groove diameter of the break-off bolt(y) with the concrete strength(x) was derived as y=0.05x+3.79, with a coefficient of determination of 0.88 found through regression analysis.

• Journal of the Korean GEO-environmental Society
• /
• v.15 no.11
• /
• pp.43-51
• /
• 2014

In this study, a series of pullout experiments were conducted on geogrid with attached passive reinforcement with respect to silt containments. Experiments were performed on man-made sand ground containing different silt of 0 %, 17 %, 35 % under various normal stresses 30 kPa, 60 kPa, 120 kPa respectively. The pullout test results showed that passive reinforcement increased the pullout strength over all silt contained condition and showed up to 20 % increases for same soil condition. The test results converted to the coefficient of interaction of pullout test to investigate the effect of reinforcement and the case of passive reinforcement showed 0.7~1.6 distribution depend on a silt contents. Therefore it is concluded that the overall length of geogrid can be reduced under the low vertical stress conditions.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.4
• /
• pp.113-123
• /
• 2007

In order to ensure the stability of reinforced structures backfilled with low permeability soil, it is very important to determine the change in undrained pullout capacity compared to drained pullout capacity prior to design. In this research, a series of numerical analyses on laboratory pullout tests have been performed on different materials (clean sand, 5, 10, and 15% silty sand), different overburden pressures (30, 100 and 200 kPa), and different drainage conditions (drained and undrained) in order to compare drained pullout capacity with undrained pullout capacity. The results of numerical analysis also have been compared with the results of the laboratory pullout tests. The analysis results show that both drained and undrained pullout capacity are influenced by silt contents and increase with increase of friction angle of the soil and overburden pressure. In undrained condition, the effective stresses acting on the reinforcement decrease as excessive pore pressures are generated, resulting in decrease in pullout capacity; 57% for 30 kPa, and 70% for 100 and 200 kPa. These results show a good agreement with the results of the laboratory pullout tests performed under the same condition.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.25 no.3
• /
• pp.13-20
• /
• 2021

Post-installed anchor is a structural material that connects structural and non-structural members to existing concrete members. However, there are cases where rebar interception and construction error occur at the site. In that case, measures are needed to prevent performance degradation of the rear-installation anchors. In this study, in order to evaluate the performance of torsional control expandable post-installed anchors for compressive strength and effective depth of the reference concrete was tested. The results of the most commonly used tests of M10 and M20 showed that had variable coefficients within 15%, satisfying the reliability presented in KCI(2017). It was also confirmed that the depth of the buried and the strength of concrete affect the strength of the pavement. Based on the results of the existing similar studies and the results of this study, the design equation of the post-installed anchor was proposed and the results were compared with the existing design.

• Journal of the Korean Geosynthetics Society
• /
• v.8 no.4
• /
• pp.19-25
• /
• 2009

In this study, field pull-out tests were performed for steel pipe nailing installed foldable wedge and non-wedge type steel pipe nailing under the same test conditions. This is to evaluate pull-out resistance improvement effect of steel pipe nailing installed foldable wedge. Evaluating for field pull-out characteristics of steel pipe nailing installed foldable wedge was performed through analysis of ultimate pull-out resistance ($T_L$), ultimate unit skin friction ($q_s$, $u_{max}$), tensile normal stiffness ($K_{\beta}$), tension of nail. As a result, the steel pipe nailing installed foldable wedge have an effect of pull-out resistance increased about 30% in comparison with non-wedge type steel pipe nailing.

• Journal of the Korea Institute of Building Construction
• /
• v.22 no.2
• /
• pp.149-160
• /
• 2022

In this study, a pull-out test considering the adhesive type, embedded length, and direction of re-bar was conducted to evaluate the pull-out performance of glued-in rod joints using timber and adhesive produced in Korea. In the test, the specimens using liquid adhesive showed better pull-out performance, and the longer the embedded length of the re-bar, the higher the maximum tensile load by inducing the yield of the re-bar first. Through the test results, a glued-in rod joints design, which is advantageous to design the adhesive strength stronger than the yield strength of re-bar, was proposed, and a correction factor of 0.75 for the adhesive strength considering construction error was also suggested.

• Journal of the Korean Geotechnical Society
• /
• v.18 no.4
• /
• pp.105-117
• /
• 2002

In the design of foundations for the super-structures such as transmission towers and oil-platforms, the foundations must be considered as a medium to resist cyclic tensile forces. In this study, the uplift capacity of the drilled shaft used as the medium resisting to this pattern of forces is investigated by performing cyclic uplift test of a small model-drilled shaft constructed in compacted granite soil in a steel chamber. In this test, the behavioral difference between a pile loaded on the top of the pile and a pile loaded at the bottom of the pile was investigated intensively. The load transfer curves obtained from the test were investigated by changing the confining pressure in the chamber. The load tests also included creep test and cyclic test. It is found from the tests that uplift capacity of the shaft loaded at the bottom is greater than that of the shaft loaded on the top of the pile. It is found also from the creep test that the pile loaded at the bottom was more stable than the shaft loaded on the top. If a pile loaded at the bottom is pre-tensioned, the pile will be most effective to the creep displacement. It is found also from the cyclic tests that apparent secant modulus obtained in a cycle of the load increases with the number of cycles.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.10 no.2
• /
• pp.69-76
• /
• 2010

This study is an numerical study of predicting the behavior of anchor embedded in weathered rocks, subjected to uplift loads, about ultimate pullout capacity and the failure mechanism. Factors influencing the behavior of anchors were investigated by reviewing the data about in-situ anchor tests performing numerical modelling with changing the bondage length of anchor, diameter of anchor body and diameter of tendon, and by correlations between those factors were evaluated to apply them to predict the behavior of anchors. As results of numerical analysis, a linear relationship between bondage length, diameter of anchor body and diameter of tendon with ultimate pullout capacity was obtained on the one hand, from the result of numerical analysis changing the Young's modulus of weathered rock, this parameter was found to influence to load-displacement and ultimate pullout capacity within the range of 10%, which was not so significant to affect.