• Proceedings of the KAIS Fall Conference
• /
• 2009.12a
• /
• pp.223-225
• /
• 2009

본 논문에서는 CRLH 전송 선로를 이용한 스터브 구조의 이중 대역 가지선로 결합기를 제안한다. 기존의 스터브 구조의 이중 대역 가지 선로 결합기는 동작하는 두 주파수가 근접할수록 스터브 선로의 임피던스가 증가해 구현이 불가능 하다. 제안된 이중 대역 가지선로 결합기는 비교적 근접한 1800MHz와 2300MHz 두 주파수에서 동작한다. 고 임피던스 스터브 선로는 이중 대역 소자 설계에 유용한 CRLH 전송 선로를 사용하여 구현 된다. 두 주파수에서 측정된 삽입 손실은 이상적인 결합기에 비해 최대 1.88dB의 오차가 났으며 두 출력 포트 사이의 위상차는 $1^{\circ}$미만 이다. 동작하는 두 주파수의 비는 1.28:1로 비교적 작은 차이를 보인다.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.9 no.5
• /
• pp.67-71
• /
• 2010

This paper proposes new dual-band impedance transformers based on the L-section circuit topology. The proposed circuits consist of a transmission line section with a stub line either at the source or at the load end. The dual-band operating conditions are analyzed in detail and simple design equations are derived in terms of the line lengths and impedances for the different circuit topologies and load conditions. The dual-band operation is confirmed through the design, fabrication and measurement in microstrip circuits based on the proposed method.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2013.05a
• /
• pp.497-499
• /
• 2013

In this paper, electrical lengths and impedances of a dual-mode resonator are calculated by using the transfer function of a dual-mode resonator by realizing the short-stub. The electrical length of transmission-line for a resonator is function of the frequency and the electrical length of stub is defined by the frequency and impedances of line and stub. Also, the inverter value of a bandpass filter using the dual-mode resonator is calculated. The effect of stub's impedance for inverter is very small. And, as the impedance of line is decreasing, the inverter value is increasing and as the bandwidth is increasing, the inverter value is increasing.

• Journal of Advanced Navigation Technology
• /
• v.20 no.1
• /
• pp.59-64
• /
• 2016

This paper presents a high dividing ratio unequal dualband divider using coplanar waveguide (CPW) and shunt connected open stub transmission lines. In order to implement transmission lines for a dualband divider using design equations, the low impedance lines of divider can be realized a shunt connected open stub transmission line. Also, the high impedance lines are realized by CPW transmission lines. To certify the validity of an unequal dualband divider using CPW and shunt connected open stub transmission lines, the 10:1 unequal dualband divider is implemented at operating frequency of 1 and 2 GHz. Good experimental performance at each frequency are obtained, which are in good agreement with the simulated results.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.25 no.10
• /
• pp.1409-1415
• /
• 2021

The Gysel divider has the advantage of easily setting the resistor in the circuit. If the line impedance in the Gysel divider is set differently, the input signal can be distributed to the two output ports at various distribution ratios. This paper proposes the Gysel divider that can change the power distribution to 1:3 or 3:1 by changing the line impedance. The impedance change of the line can be implemented by placing a floating copper plate on the bottom of the microstrip-line. When the floating copper plate and the ground plane are connected, the line operates as the microstrip-line, and when the floating copper plate and the ground plane are disconnected, the line operates as the coplanar-line. The proposed Gysel divider was fabricated at the center frequency of 1.5GHz. The fabricated 3:1 Gysel divider has a stable value S₁₁ of below -17dB, S₂₁/S₃₁ of 4.8±0.2dB, S₂₁(to high output port) of -1.39±0.12dB and S₃₁(to low output port) of -6.15±0.08dB over 1.3~1.7GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.7 no.2
• /
• pp.167-177
• /
• 1996

The cutoff frequencies of a double ridged rectangular waveguide are calculated by applying the modal analysis to its cross-section. And the characteristic impedance of its $TE_{10}$ mode is evaluated in a frequency range of 6 to 18 GHz. When both ends of a linearly tapered rectangular wa- veguide consists of single and double ridged rectangular cross-sections, the equivalent nonuniform transmission line of its $TE_{10}$ mode is solved numerically. It is shown that the input impedance at its single ridged terminal becomes nearly constant in the wide bandwidth.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.9
• /
• pp.800-807
• /
• 2016

In this paper, we study the characteristics of dual band microstip antenna with modified inset feeder and a single slot. The modified inset feeder consists of the vertical inset feeder placed in x direction and the horizontal one in y direction for shortening the total length of inset feeder. The optimun feeding position for good impedance matching at two resonant frequencies can be easily found by adjusting the horizontal inset distance. And Various frequency ratios can be simply obtained by the parameters of slot. The measurements for fabricated antenna prototypes are carried out for validation. The measured results show a tunable frequency ratio from 1.25 to 1.88 with the variation of slot parameters. It is worthwhile to point out that the radiation patterns are similar at both bands. and below -20.0 dB of cross polarization level at the E plane.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.10
• /
• pp.2339-2344
• /
• 2014

of a microstrip transmission line, this transmission line can operate as the microstrip line or the coplanar line according to open or short connection between the ungrounded copper plane and grounded plane on the base plane. Two different type operation of the transmission line means that one transmission line can have two different characteristic impedances. This paper proposes and fabricates the circuit to be operated 2-ports power transmission line or 2-way power divider with the stable input matching characteristic by using this dual-impedance transmission line. The proposed circuit operates 2-ports power transmission line in case of the coplanar line or 2-way power divider line in case of the microstrip line. The fabricated circuit shows $S_{21}$ > -0.2 dB and $S_{11}$ < -15 dB above 700 MHz when the circuit operates 2-ports power transmission line. And, it is $S_{21}$ > -3.8 dB, $S_{11}$ < -10 dB and $S_{21}/S_{31}$ < ${\pm}0.3dB$ above 700 MHz when the circuit operates 2-way power divider.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.3
• /
• pp.379-387
• /
• 2000

In this paper, to transmit and receive the differently polarized wideband signals simultaneously with a single antenna system, the wideband, dual-frequency and dual-polarized(WDFDP) microstrip array antenna is proposed and designed. This antenna operates simultaneously at 14.25 GHz and 12.50 GHz. To extend to two dimensional array, microstrip feed line and coaxial probe through via-hole are used. The experimental results show that the proposed WDFDP microstrip antenna can be used in the compact portable terminals with a single antenna system and the characteristic of the resonators in this antenna produces a greatly enhanced bandwidth.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.7
• /
• pp.1053-1064
• /
• 1999

In this paper, to transmit and receive the differently polarized signals simultaneously with a single antenna system, the dual-frequency microstrip array antenna with dual-polarization is proposed and designed. This antenna operates simultaneously at 14.25 GHz and 12.50 GHz. To extend to two dimensional array, microstrip feed line and coaxial probe through via-hole used.