• 대한기계학회논문집
• /
• 제9권4호
• /
• pp.478-486
• /
• 1985

본 논문에서는 이러한 점에 대처하고 얇은 림 내접치차의 이뿌리응력을 해석, 이 결과를 종합하여 얇은 림 내접치차의 이뿌리응력을 간편하게 계산할 수 있는 근사 계산식을 작성한다. 또 스트레인게이지에 의한 이뿌리응력의 실측치와 이계산식에 의한 계산응력치를 비교검토하여 이 계산식의 계산정밀도 및 신뢰성을 검토하기로 한 다.

• 한국정밀공학회지
• /
• 제8권2호
• /
• pp.89-105
• /
• 1991

A method to apply the approximation formulae[1] for tooth fillet and root stresses of a thin-rimmed rack to the calculation of stress state of thin-rimmed external and internal spur gears is introduced. The stress values by the method proposed in this paper have shown good agreement with those by the REM analysis and also by the stress measurement of strain survey investigation. By this method, reliable stress state at tooth fillet and root areas in the thin-rimmed external and internal spur gears can be easily calculated, and a practical design method for the bending strength of such thin-rimmed gears is established.

• 한국공작기계학회논문집
• /
• 제16권4호
• /
• pp.45-50
• /
• 2007

In this paper, the FEM(Finite Element Method) has been applied to understand the geometrical characteristics and to analyze the stress of a helical gear. The helical gear is simulated and analyzed by adding many thin spur gear with helix angles and twist angles. Helical gears with different helix angle and face width have been studied. The results show that the root fillet stress is increased proportionally to helix angle and face width. Namely, as the face width increases, root fillet stress decreases, and as helix angle gets bigger, root fillet stress increases.

• 대한기계학회논문집
• /
• 제11권2호
• /
• pp.198-204
• /
• 1987

본 논문에서는 전보에서 창성된 인벌류우트-원호합성치형기어에 있어서 Hertz 식에 의하여 치면접촉응력을 구하고 유한요소법에 의하여 이뿌리응력을 계산하였다. 그리고 같은 제원의 표준 인벌류우트 치형기어와 비교하였다.

• 대한기계학회논문집
• /
• 제18권5호
• /
• pp.1126-1133
• /
• 1994

When designing an internal gear. the bending strength around pitch point as well as that at tooth root fillet should be considered because the bending stress around pitch point may occur as high as that at tooth root fillet. In this study, including stress state around pitch point, the bending strength (tensile side and compressive side) of internal gear tooth is investigated by the use of the finite element method(FEM) with regarding many influencing factors of cutter and gear geometries. Then, the critical sections around pitch point and at tooth root fillet are determined, and the simple formulae based on nominal stresses(bending, compressive, and shear) are derived for the calculations of actual stresses as the functions of tooth thicknesses and radii of curvatures of involute and fillet curve at those critical sections. The stresses calculated by the formulae agree well with those by the FEM. And the bending stresses around pitch point and at tooth root are easily estimated by the use of those formulae, therefore, those formulae are useful for the purpose of the design or the bending strength estimation of internal gear.

• 한국공작기계학회논문집
• /
• 제10권5호
• /
• pp.85-95
• /
• 2001

This study proposed a technique for inverse problem, linear approximation of contact position and loading in single and double meshing of spiral bevel gear , using 2-dimension model considered near the tooth by root stress. Determine root stress is carried out far the gear tooth by finite element method and boundary element method. Boundary element discretization near contact point is carefully performed to keep high computational accuracy. And from those estimated results, the comparing estimate value with boundary element method value was discussed.

• 한국공작기계학회논문집
• /
• 제12권5호
• /
• pp.24-33
• /
• 2003

This study proposed a technique for inverse problem, linear approximation of contact position and loading in single and double meshing of transmission contact element using 2-dimension model considered near the tooth by root stress. Determination of root stress is carried out far the gear tooth by finite element method and boundary element method. Boundary element discretization near contact point is carefully performed to keep high computational accuracy. The predicted results of boundary element method are good accordance with that of finite element method.

• 한국자동차공학회논문집
• /
• 제16권6호
• /
• pp.97-103
• /
• 2008

In general, the strength of gears is calculated using the formula of AGMA or JGMA. But these formula can not be applied directly to the strength calculation of the rack and pinion of steering gear assay, because of complex tooth and contact shapes. So Lewis bending stress and Hertzian contact stress formula are generally used for the design of rack and pinion of steering gear assay. But these formula do not also give the exact stress of rack and pinion. In this paper, comparing the finite element analysis results and the experimentally measured values, it is shown that the finite element modeling technique of the rack and pinion of steering assay is reasonable.

• 한국기계가공학회지
• /
• 제13권5호
• /
• pp.15-20
• /
• 2014

The wind industry grew in the first decade of the 21st century at rates consistently above 20% a year. For wind turbine, gearbox failure can be extremely costly in terms of repair costs, replacement parts, and in lost power production due to downtime. In this paper, gear tooth micro-modification for the high speed stage was used to compensate for the deformation of the teeth due to load and to ensure a proper meshing to achieve an optimized tooth contact pattern. The gearbox was firstly modeled in a software, and then the various combined tooth modification were presented, and the prediction of transmission under the loaded torque for the helical gear pair was investigated, the normal load distribution and root stress were also obtained and compared before and after tooth modification under one torque. The simulation results showed that the transmission error and normal load distribution under the load can be minimized by the appropriate tooth modification. It is a good approach where the simulated result is used to improve the design before the prototype is available for the test.