• Journal of Korean Tunnelling and Underground Space Association
• /
• v.15 no.3
• /
• pp.237-251
• /
• 2013

This study aimed to estimate the axial stress and torque on a shaft in a disc cutter. The corresponding inner temperature and the surface temperature of a cutter ring were also measured by using strain gauges and thermocouples during the linear cutting tests. The maximum values of the axial stress and torque were recorded to 11.3 MPa, $171kN{\cdot}m$ respectively. They have higher correlations with normal force rather than rolling force. The results of temperature measured by thermocouples during a linear cutting test showed that the rate of increase in temperature was below $0.2^{\circ}C$. When the cutter spacing is set to be 70 mm, the inner temperature and surface temperature of a disc cutter were $0.1^{\circ}C/m$, $0.15{\sim}0.17^{\circ}C/m$ respectively. Similarly, when the cutter spacing is 90 mm, the temperature values were $0.09^{\circ}C/m$, $0.13{\sim}0.23^{\circ}C/m$ respectively.

• The Journal of Engineering Geology
• /
• v.31 no.2
• /
• pp.149-163
• /
• 2021

Damage characteristics of granite, marble and sandstone whose properties were different were investigated by uniaxial compression test and cyclic loading-unloading test. Strength, elastic constants and damage threshold stresses were measured by uniaxial compression test and were compared with those measured by cyclic loading-unloading test. Average rock strengths measured by cyclic loading-unloading test were either lower than or similar with those measured by uniaxial compression test. Rocks with high strength and low porosity were more sensitive to fatigue than that with low strength and high porosity. Although permanent strains caused by cyclic loading-unloading were different according to rock types, they could be good indicators representing damage characteristics of rock. Damage threshold stress of granite and marble might be measured from stress-permanent strain curves. Acoustic emissions were measured during both tests and felicity ratios which represented damage characteristics of rocks were calculated. Felicity ratio of sandstone which was weak in strength and highly porous could not be calculated because of very few measurements of acoustic emissions. On the other hand, damage threshold could be predicted from felicity ratios of granite and marble which were brittle and low in porosity. The deformation behaviors and damage characteristics of rock mass could be investigated if additional tests for various rock types were performed.

• The Journal of Engineering Geology
• /
• v.34 no.3
• /
• pp.381-401
• /
• 2024

To predict the ground subsidence caused by mines, various evaluation methods were applied to cases of ground subsidence in Korea, and the results were compared and analyzed. Continuous subsidence, which is relatively easily and accurately predicted, was excluded in this analysis. The stress arch - volumetric expansion method, limit equilibrium method, numerical analysis, probabilistic method, and evaluation method of the Korea Mine Rehabilitation and Mineral Resources Corporation (KO MIR) were applied to 36 subsidence cases, including subsidence location, width, and depth, and goaf width, depth, and incline data. The stress arch - volumetric expansion method was the most accurate with an accuracy of ~92%. In the case of the KOMIR method, the regression model is 86.1% accurate, but somewhat lower in accuracy using a triangular pyramidal volume. The stress arch - volumetric expansion and KOMIR methods have the disadvantage of evaluating whether subsidence occurs or not. In the case of the numerical analysis, the accuracy is 72.3% when estimating the subsidence depth, but is slightly lower (55.8%) when estimating the subsidence width. The probabilistic and limit equilibrium methods have similar accuracies of 50.8~63.7%. Given it is possible to determine whether subsidence occurs, and the subsidence location, width, and depth with each method, it is recommended to apply various methods when evaluating sinkhole-type subsidence.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2003.03a
• /
• pp.161-168
• /
• 2003

평판재하시험은 재하시험시 표층의 매우 잘 다져진 곳에 대한 지지력 계수를 획득하여 실다짐도를 과대 평가하는 결과를 초래할 수 있다. 이에 착안하여 응력도달 범위가 작은 평판재하시험을 지양하고 콘관입시험으로부터 획득되는 노상의 관입지수로부터 지반의 다짐도를 추정할 수 있는 콘관입시험기와 구동시스템 및 해석 프로그램을 개발하였다.

• Journal of Welding and Joining
• /
• v.8 no.1
• /
• pp.2-11
• /
• 1990

오-스테나이트계 스테인레스강을 용접육성한 강판의 박리균열의 원인에 대하여 강중의 수소거동을 중심으로 고찰해 보았다. 강중의 수소온도 분포를 추정하는데는 확산 방정식을 기초로하여 수치해석이 유력하며 그 기초적사항에 대해 제문헌을 인용하여 설명했으며, 또 시험편에 대하여 계산과 실험치의 결과를 이용하여 비교하였다. 이들로부터 박리균열의 발생에 대한 미시적 임계조건을 도출하여, 이들이 한정된 실험의 범위내이지만 실증할 수 있음을 나타내었다. 그러나 박리균열의 원인의 하나인 잔류응력에 대해서는 아직 불명한 점이 많으나, 냉각속도에 따라 변화하며 그것이 수소농도라고 하는 관점에서 미시적 임계조건에 영향을 미칠 수 있음을 시사하고 있다.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.11a
• /
• pp.319-322
• /
• 2005

When a concrete structure is subjected to load, its response is both immediate and time dependent. Under sustained load, the deformation of a structure gradually increases with time and eventually may be many time greater than its instantanneous value. The gradual development of strain with time is caused by creep and shrinkage. On this study, to estimate of stress variations on time effects in partially prestressed concrete composite girder bridges, computer program applied Age-adjusted Effective Modulus Method(AEMM) in used.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.11a
• /
• pp.675-678
• /
• 2004

The importance of predicting concrete compressive strength of in concrete structures is gradually increasing in construction industry. The estimation of concrete compressive strength of is a critical factor of the construction schedule and quality control. This study was performed to examine the relationship between concrete compressive strength and stress wave velocity which was determined by the impact echo method and SASW method.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.11a
• /
• pp.357-360
• /
• 2006

Under sustained load, the stress variation occurs due to creep and shrinkage of concrete on the sections of steel-concrete composite girders. In standard specification for highway bridge, the method of stress estimation considering time effects is based on the concept of Yassumi method. In this study, comparing the analysis results using the AEMM and Yassumii method long-term behaviors, the rationality of specified requirements is checked.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.12 no.3
• /
• pp.485-494
• /
• 1999

본 연구에서는 요소를 사용하지 않고 절점들만을 이용하여 해석이 가능한 새로운 수치해석기법인 EFG(Element-Free Galerkin)법을 사용하여 임의의 균열의 성장과정을 해석할 수 있는 효율적인 알고리즘을 개발하고, 이를 바탕으로 균열의 성장방향과 경로를 정확히 추정하여 일련의 균열진전해석을 수행할 수 있는 프로그램을 개발하였다. 균열해석에 있어서는 균열선단의 특이성과 균열면의 분연속성을 수치적으로 반영할 수 있는 기법을 도입하여 균열을 모형화하였으며, 선형탄성파괴역학이론에 근거하여 균열해석과정을 정식화하였다. 또한, EFG 형상함수가 kronecker delta 조건을 만족시키지 못함으로써 발생하는 필수경계조건의 처리문제를 penalty법을 이용하여 해결하였다. 개발된 균열진전해석 알고리즘을 정지상태와 성장하는 상태에 있는 모드 Ⅰ, 모드 Ⅱ 및 혼합모드상태의 대표적인 균열문제들에 적용하여 응력확대계수와 균열성장방향 및 균열의 성장경로를 추정하고 이를 이론적·실험적 결과들과 비교함으로써 그 정확성과 효율성을 검증하였다.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2002.04a
• /
• pp.303-306
• /
• 2002

변위가 발생한 해안도로 옹벽에 대한 원인을 규명하기 위하여 기반암과 매립부 지반에 대한 조사를 실시하였다. 연구지역에서 지질구조선의 발달은 관찰되지 않고 지표에서 기반암의 거동은 낙석의 형태로 나타난다. 기반암은 생교란작용의 유무에 따라 상, 하부지층이 구분되며 하부 지층은 신선한 상태로 이완된 불연속면은 나타나지 않는다. 변위는 옹벽의 이음부에 집중되며 옹벽의 운동방향은 우향이동과 좌향이동이 반복되며 최초 변위 발생지점 (시 점부)에서 멀어짐에 따라 장력에 의한 확장 (벌어짐)이 우세하며 종점부에서 회전운동이 수반된다. 이음부의 확장과 회전은 최초 발생 지점에서 응력이 전달되는 과정에서 나타난 것으로 해석된다. 매립부 지반의 전기비저항탐사에서 상부의 매립층은 높은 전기비저항을 가지는 것에 반해 하부는 매우 낮은 전기비저항 값을 보여준다. 이는 매립부의 하부지반이 해수면 이하에 위치하여 해수와 같은 유체의 영향을 받으나, 상부는 유체의 영향을 거의 받지 않는 것으로 추정된다. 반면 최초 변위가 발생한 지점의 매립부 지반은 하부와 같이 낮은 전기비저항 값을 보여준다. GPR 탐사에서 최초 변위 발생 지점에서 매질의 이완 내지 공동으로 추정되는 구조가 관찰된다.