• Journal of the Institute of Convergence Signal Processing
• /
• v.8 no.1
• /
• pp.32-38
• /
• 2007

In order to establish the environmental condition of sounds in the classroom, we measured the impulse response in cases of using and not-using PA(Public-Address). By calculating the physical index of acoustics, I examined the differences between the two cases. The degree of improvement in listening with the help of PA has also been studied by testing the voice articulation with the use of the measured impulse response. As a result, I found that the clearness is enhanced by increasing the sound pressure level in the case of short reverberation. However, it was not the case when the reverberation time was long.

• The Journal of the Acoustical Society of Korea
• /
• v.15 no.2
• /
• pp.72-78
• /
• 1996

This thesis deals with a method to solve a two-and-one-half-dimensional ($2\frac12$ D) problem, which means that the ocean environment is two-dimensional whereas the source is fully three-dimensionally propagating, including three-dimensional refraction phenomena and three-dimensional back-scattering, using two-dimensional two-way parabolic equation method combined with Fourier synthesis. Two dimensional two-way parabolic equation method uses Galerkin's method for depth and Crank-Nicolson method and alternating direction for range and provides a solution available to range-dependent problem with wave-field back-scattered from discontinuous interface. Since wavenumber, k, is the function of depth and vertical or horizontal range, we can reduce a dimension of three-dimensional Helmholtz equation by Fourier transforming in the range direction. Thus transformed two-dimensional Helmholtz equation is solved through two-way parabolic equation method. Finally, we can have the $2\frac12$ D solution by inverse Fourier transformation of the spectral solution gained from in the last step. Numerical simulation has been carried out for a canonical ocean environment with stair-step bottom in order to test its accuracy using the present analysis. With this spectral parabolic equation method, we have examined three-dimensional acoustic propagation properties in a specified site in the Korean Straits.

• The Journal of the Acoustical Society of Korea
• /
• v.38 no.4
• /
• pp.406-413
• /
• 2019

This paper proposes a speech enhancement method through the process of combining the gain function with spectrum subtraction method in the two microphone array with close spacing. A speech enhancement method that uses a gain function estimated by the SNR (Signal-to Noise Ratio) based on the multi frequency band coherence function causes the performance degradation in high correlation between input noises of two channels. A new speech enhancement method is proposed where the weighted gain function is used by combining the gain function from the spectral subtraction. The performance evaluation of the proposed method was shown by comparison with PESQ (Perceptual Evaluation of Speech Quality) value which is an objective quality evaluation test provided by the ITU-T (International Telecommunications Union Telecommunication). In the PESQ tests, the maximum 0.217 of PESQ value is improved in the various background noise environments.

• Journal of Adhesion and Interface
• /
• v.6 no.2
• /
• pp.13-20
• /
• 2005

Interfacial shear strength (IFSS) of environmentally friendly natural fiber reinforced polymer composites plays a very important role in controlling the overall mechanical performance. The IFSS of various Ramie and Kenaf fibers/epoxy composites was evaluated using the combination of micromechanical test and nondestructive acoustic emission (AE) to find out optimal conditions for desirable final performance. Dynamic contact angle was measured for Ramie and Kenaf fibers and correlated the wettability properties with interfacial adhesion. Mechanical properties of Ramie and Kenaf fibers were investigated using single-fiber tensile test and analyzed statistically by both uni-and bimodal Weibull distributions. An influence of clamping effect on a real elongation for both Ramie and Kenaf fibers were evaluated as well. Two different microfailure modes, axial debonding and fibril fracture coming from fiber bundles and single fiber composites (SFC) were observed under tension and compression.

• Journal of Welding and Joining
• /
• v.11 no.2
• /
• pp.1-12
• /
• 1993

용접과 관련되는 분야에서, 재료평가와 비파괴 검사법으로서의 Acoustic Emission의 응용을 살펴 보았다. 재료 평가법으로서의 AE는 다른 시험방법들이 검출해 내지 못하는 재료 내부에서의 미시적인 현상들을 정량적으로 평가할 수 있는 장점을 가지고 있다. 앞으로 새로운 용접재료의 개발이라든지, 고도의 신뢰성이 요구되는 용접부위의 정량적인 평가를 위해서 AE의 응용은 중요한 정보들을 제공하게 될 것이다. 한편 용접구조물의 비파괴적 평가법으로서의 AE는 균열의 동적인 거동 및 균열의 위치를 검지할 수 있다는 장점 때문에 응용범위는 더욱 넓어질 것이다. 여기서 유의하여야 할 점은, 목적으로 하는 AE신호를 수만배 까지 증폭시키는 과정에서 환경잡음의 영향을 무시할 수 없는 경우에는 우선적으로 잡음을 적극적으로 제거하는 고도의 연구도 함께 병행되어야 한다는 것이다.

• The Journal of the Acoustical Society of Korea
• /
• v.40 no.1
• /
• pp.46-54
• /
• 2021

In this paper, active noise control was performed to reduce radiated noise in the low frequency band of dishwashers. First, through an analysis of the noise environment of the dishwasher, it was confirmed that the pump noise contributed the most to the radiated noise in the low frequency band, From the result of the noise environment analysis, the reference signal was selected to be the vibration signal of the pump body. The reference signal was obtained by using the accelerometer on the pump body, which can prevent acoustic feedback. The error signal sensor was selected as a microphone located at 1 m in front of the dishwasher and 0.5 m in height. And to design the controller, the error signal and the reference signal were measured at the operational rpms of the dishwasher at 2,500 rpm, 2,600 rpm and 2,800 rpm, and the secondary path transfer function was measured. The designed controller was mounted on Digital Signal Processor (DSP) equipment, and the control performance was verified experimentally. As a result of the measurement at the 3 operational rpms, the 7th multiple component of pump operating frequency decreased by 1.93 dB, 4.43 dB, 5.15 dB per rpm, and the 12th multiple component decreased by 6.67 dB, 2.34 dB, 4.28 dB per rpm. And overall Sound Pressure Level (SPL) decreased by 0.84 dB, 2.58 dB, 1.48 dB by rpm.

• Fire Science and Engineering
• /
• v.30 no.4
• /
• pp.1-5
• /
• 2016

This research performed tests of Video Fire Detector and criteria of installation to make suggestions regarding the criteria that must be reflected in NFSC 203 by comparing the standards of FM Approvals, UL, ISO7240 and NFPA 72. FM Standard related to Video Fire Detector test has been classified as Smoke, Flame type, but the UL Standard has classified only as a Smoke type. This research examined 6 cases of fire phenomenon detection case in ISO 7240 and 3 cases in NFPA 72, respectively. There are 15 items required for the installation standard of a Video Fire Detector and each field standard is presented as a per installation method. To apply a Video Fire Detector, the pertinent items (the definition of term, detector's classification, structure and function among its test item) must be inserted. In addition, 7 items of the fire test, i.e., the sensitivity adjustment, prevent false alarm, ambient temperature test, the effective sensitivity and detection distance and viewing angle, aging test, flood test, must be applied to the actual test. For installation in the field, the operation environment and levels of illumination, and NFSC 203 must be set, and standards relevant to the sound system, indicators' installation distance, etc. need to be inserted.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.23 no.3
• /
• pp.212-219
• /
• 2003

This study is to evaluate the characteristics of SCC at the welded region of high strength steel using acoustic emission(AE) method. Specimens were loaded by a slow strain rate method in synthetic seawater and the damage process was monitored simultaneously by AE method. Corrosive environment was controlled using the potentiostat, in which -0.8V and -1.1V were applied to the specimens. In the case of one-pass weldment subjected to -0.8V, much more AE counts were detected compared with the PWHT specimen. It was verified through the cumulative counts that coalescence of micro cracks and cracks for the one pass weldment with -0.8V were mostly detected. In case of the one pass weldment subjected to -1.1V, time to failure became shorter and AE counts were produced considerably as compared with that of the two pass weldment. It was shown that AE counts and range of AE amplitude have close relations with the number and size as well as width of the cracks which were formed during the SCC.

• Composites Research
• /
• v.20 no.3
• /
• pp.55-62
• /
• 2007

Interfacial evaluation and durability of Jute and Hemp fibers/polypropylene (PP) composites were investigated. Moisture content of various treated conditions were measured by thermogravimetic analyzer (TGA). After boiling water test, mechanical properties and IFSS between Jute, Hemp fibers and PP matrix decreased. On the other hand, work of adhesion increased due to swelled fibril by water. Surface energies of Jute and Hemp fibers before and after boiling water test were obtained using dynamic contact angle measurement. IFSS was not always consistent with thermodynamic work of adhesion. In boiling water case, since Jute and Hemp fibers could be swelled by water, surface area and moisture infiltration space increased. Environmental effect on microfailure modes of Jute or Hemp fibers and Jute or Hemp fibers/PP composites were obtained by observing via optical microscope and by monitoring acoustic emission (AE) events and their AE parameters. After boiling water test, unlike Hemp fiber, microfailure process of Jute fiber could occur due to low tensile strength by swelled fibril. In addition, AE events occurred more and AE amplitude and energy became lower than those of before boiling water test.

• The Journal of the Acoustical Society of Korea
• /
• v.36 no.5
• /
• pp.293-299
• /
• 2017

Small unmanned platforms maneuvering underwater are the key naval future forces, utilized as the asymmetric power in war. As a method of detecting and identifying such platforms, we introduce a property estimation technique based on an iterative numerical analysis. The property estimation technique can estimate not only the position of a target but also its physical properties. Moreover, it will have a potential in detecting and classifying still target or multiple targets. In this study, we have conducted the property estimation of an small underwater target using the data acquired from the lake experiment. As a result, it shows that the properties of a small platform may be roughly estimated from the in site data even using one channel.