• Bulletin of the Society of Naval Architects of Korea
• /
• v.7 no.1
• /
• pp.27-36
• /
• 1970

선박유체역학(船舶流體力學)의 경계조건(境界條件)의 선형화(線型化)를 위한 퍼터베이션(Perturbation)방법(方法)을 따라 배를 가늘고 길게 보느냐, 엷은 수평판(水平板)으로 보느냐 등등에 따라 여러가지 다른 종류(種類)의 수학적(數學的) 정의(定義)에 따르는 이론(理論)을 추궁함으로서, 1) Neumann Ship, 2) Thin Ship, 3) Michell Ship, 4) Slender Ship 등을 이론적(理論的)인 면(面)에서와 수치계산(數値計算) 예(例)로서 비교검토(比較檢討) 하였다. 동시(同時)에 이에 따르는 "직접문제(直接問題)" "간접문제(間接問題)" 등(等)에 관(關)하여도 언급(言及)하고 그 차이점(差異點)을 지적하였다. 이에 의(依)하면 정속전진시(定速前進時)에 L/B가 10인 경우에는 최대광폭의 차(差)가 $5{\sim}8%$정도 되고 또 선수수선반각(船首水線半角)에 상당한 차(差)가 있음으로 같은 이론적(理論的)인 계산치(計算値)에 대(對)하여 저항(抵抗)은 적어도 $10{\sim}15%$정도 차(差)가 생길 것이 아닌가 보게끔 되었다.

• Journal of Ocean Engineering and Technology
• /
• v.15 no.2
• /
• pp.1-5
• /
• 2001

A study on the new active type oil-water separation system including the oil-water separation system of magnetic film was carried out. Separation system is composed of several active types of circulating oil separation steps and one magnetic film separation step at final stage. At the magnetic separation step, ferrofluid easily forms a weak magnetic mixture with oil, which is from the water by magnetic field gradient. The vessel has been designed to run at the maximum speed of 25 knots. And two typical forms of SWATH and Catamaran have been studied as a new type of oil recovery vessel.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2658-2663
• /
• 2008

In the present study, we designed a microfluidic flatform that generates monodisperse droplets with diameters ranging from hundreds of nanometers to several micrometers. To generate fine droplets, T-junction and flow-focusing geometry are integrated into the microfluidic channel. Relatively large aqueous droplets are generated at the upstream T-junction and transported toward the flow-focusing geometry, where each droplet is broken up into the targeted size by the action of viscous stresses. Because the droplet prior to rupture blocks the straight channel that leads to the flow-focusing geometry, it moves very slowly by the pressure difference applied between the advancing and receding regions of the moving droplet. This configuration enables very low flow rate of inner fluid and higher flow rate ratio between inner and outer fluids at the flow-focusing region. It is shown that the present microfluidic device can generate droplets with diameters about 1 micrometer size and standard deviation less than 3%.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2670-2675
• /
• 2008

We introduce a new type of surface microscope using hydrodynamic phenomena. The fluid flow through the opening of the pipette probe is blocked at short distances between the probe and the surface, thus increasing the pressure loss. Therefore, a scanning flow impedance microscope (SFIM) can image the surface topology by scanning the probe with measuring the pressure loss. The SFIM can display the topology regardless of surface hardness, surface electrical conductivity, and surrounding fluid. The present letter contains the first experimental results on surface topography obtained with this novel microscope. The preliminary results in air demonstrate the lateral resolution of the SFIM is very close to the inner diameter of the probe.

• Journal of the Society of Naval Architects of Korea
• /
• v.29 no.3
• /
• pp.102-116
• /
• 1992

This report is to provide a comparison of the hydrodynamic characteristics of a single strut SWATH(Small Waterplane Area Twin Hull) model and a tandem(twin) strut SWATH model. The hydrodynamic characteristics included are the resistance in calm water, 6 degree freedom of motion responses in stationary and with forward speeds, and wave loadings etc. All these quantities are measured in the towing tank and compared with the computational results. Based on the present study, the pros and cons for single and tandem strut SWATH designs are clarified and some design suggestions are made.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.13 no.12
• /
• pp.1275-1281
• /
• 2001

Aqueous polymer solutions are known to have small pressure reduction. Paraffin slurries are known to have high thermal capacity. Paraffin particles are mixed into an aqueous polymer solution to make a new heat transfer fluid having high thermal capacity but low pressure reduction. The heat transfer characteristics of the new slurry was tested in a circular tube having a constant heat transfer boundary condition. The new slurry was found to have high Nusselt numbers as well as high thermal capacity and low pressure reduction in the laminar flow. The trends of the Nusselt numbers along the heating test section were studied for various heating conditions.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1997.04b
• /
• pp.52-55
• /
• 1997

여과가 진행됨에 따라 막의 표면에서 발생하여 여과선속을 저하시키는 케이크층의 형성은 막을 이용한 고-액 분리공정에서 발생하는 가장 큰 문제점의 하나로서 이는 막 분리공정의 경제성을 좌우하는 중요한 인자가 된다. 이러한 문제점을 극복하기 위하여 유체와 막 사이의 상대속도를 증가시켜 여과속도를 향상시키는 십자흐름 여과, 즉 CFF(crossflow filtration)에 대한 연구가 활발히 진행되어 왔다. 그러나 이러한 심자흐름 여과에서도 막과 유체 사이의 상대속도의 증가에 한계가 있고 또한, 막의 기공보다 작은 입자가 막의 기공 내에 침투하여 막을 오염시키는 현상을 예측하기 어렵기 때문에 여과기의 설계에 있어서 많은 문제점이 발생하고 있다. 이에 오염된 막을 재생시키기 위하여 기계적.화학적인 여러 가지 방법들이 개발되고 여과선속을 향상시키는 방법이 꾸준히 연구되어 분리막 기술의 경제성을 향상시켜 왔다. 본 연구에서는 매우 안정된 유동의 하나로서 막 표면의 전단력을 향상시키는 데에 효과가 있다고 알려진 Taylor와류를 응용한 회전막 여과기를 사용하여 여러 가지 크기의 입자에 대한 여과실험을 수행함으로써 이러한 유동이 케이크의 형성에 미치는 영향을 살펴보았다. 또한 여과선속에 영향을 미치는 여러 매개인자를 알아보고 실험결과를 간단한 모델식에 적용해 봄으로써 막의 저항을 예측할 수 있는 모델식으로의 개선 방향을 제시하고자 한다.

• Journal of computational fluids engineering
• /
• v.21 no.3
• /
• pp.71-76
• /
• 2016

In speed skiing, aerodynamic forces play an important role in determining performance of the skier. To predict aerodynamic effects of the posture of the skier on alpine downhill skiing, we constructed equation of motion of the skier and performed the corresponding CFD simulations. Comparing drag and lift of three different skier postures, it has been shown that drag decreases significantly by tucking upper body to lower body and stretching arms forward. Also, aerodynamic lift which worked as downforce in standing posture worked upward in tuck posture, reducing friction force between snow and ski. This indicates that tuck posture have advantages over standing posture in dual mechanism, namely by reducing drag and also increasing lift. By this two-dimensional initial study we could reveal the general tendency of the aerodynamic force over the skier's body. This study not only provides a theoretical foundation for the athletes to understand the aerodynamic effects of skier postures but also shed a light on towards more accurate and rational three-dimensional CFD simulation of skiers in the near future study.

• Journal of Navigation and Port Research
• /
• v.47 no.6
• /
• pp.305-314
• /
• 2023

In this study, a mathematical model of a 9.77 G/T small fishing vessel was established based on captive model tests. The powering and manoeuvring performances of the vessel in the harbor and coastal sea were focused on, so captive model tests were conducted up to the full-scale speed of 8 knots. Propeller open water, resistance, and self-propulsion tests of a 1/3.5-scaled model ship were performed in a towing tank, and the full-scale powering performance was predicted. Hydrodynamic coefficients in the mathematical model were obtained by rudder open water, horizontal planar motion mechanism tests of the same model ship. In particular, in static drift and pure yaw tests which were conducted at a speed of 2 to 8 knots, the linear hydrodynamic coefficients varied with the ship speed. The effect of the ship speed on the linear coefficients was considered in the mathematical model, and manoeuvring motions, such as turning circles and zig-zags, were simulated with various approach speeds and analyzed.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.7
• /
• pp.599-607
• /
• 2015

In this study, we theoretically investigate the thermal performances of heat pipes that have different nano-fluid properties. Two different types of nano-particles have been used: $Al_2O_3$ and CuO. The thermal performances of the heat pipes are observed for varying nano-particle aggregations and volume fractions. Both the viscosity and the conductivity increase as the volume fraction and the aggregation increase, respectively. Increasing the volume fraction helps increase the capillary limit in the well-dispersed condition. Whereas, the capillary limit is decreased under the aggregate condition, when the volume fraction increases. The dependence of the heat pipe thermal resistance on the volume fraction, aggregation, and conductivity of the nano-particles is analyzed. The maximum thermal transfer of the heat pipe is highly dependent on the volume fraction because of the high permeability of the heat pipe. For the proposed heat pipe, the optimum volume fraction of the nano-particle can be seen through 3D graphics.