• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.35S no.10
• /
• pp.1-10
• /
• 1998

It is important to know phase offsets of a spreading code in the code division multiple access(CDMA) mobile communication systems because different phase offsets of the same spreading code are used to distinguish each base station. When the period of the code is not that long, the relative phase offset between the code and its shifted code can be found by comparing them, but as the period of the code increases it becomes difficult to find the phase offset. This paper describes a method to calculate the phase offset of a binary code based on the number theoretical approach. We define an accumulator function which plays a central role in this paper, and relationships between the functions are clarified. This number theoretical approach and their results show that this method is very easy for the phase offset calculation. Its application to the CDMA system and circuit realization of the phase offset calculation are also discussed.

• Journal of Korean Society for Geospatial Information Science
• /
• v.22 no.1
• /
• pp.47-54
• /
• 2014

Precise Point Positioning (PPP) algorithms using GPS code pseudo-range measurements were developed and their accuracy was validated for the purpose of implementing them on a portable device. The group delay, relativistic effect, and satellite-antenna phase center offset models were applied as fundamental corrections for PPP. GPS satellite orbit and clock offsets were taken from the International GNSS Service official products which were interpolated using the best available algorithms. Tropospheric and ionospheric delays were obtained by applying mapping functions to the outputs from scientific GPS data processing software and Global Ionosphere Maps, respectively. When the developed algorithms were tested for four days of data, the horizontal and vertical positioning accuracies were 0.8-1.6 and 1.6-2.2 meters, respectively. This level of performance is comparable to that of Differential GPS, and further improvements and fine-tuning of this suite of PPP algorithms and its implementation at a portable device should be utilized in a variety of surveying and Location-Based Service applications.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.9
• /
• pp.74-80
• /
• 2009

This paper describes a $2{\sim}6GHz$ CMOS frequency synthesizer that employs only one LC-tank voltage controlled oscillator (VCO). For wide-band operation, optimized LO signal generator is used. The LC-tank VCO oscillating in $6{\sim}8GHz$ provides the required LO frequency by dividing and mixing the VCO output clocks appropriately. The frequency synthesizer is based on a fractional-N phase locked loop (PLL) employing third-order 1-1-1 MASH type sigma-delta modulator. Implemented in a $0.18{\mu}m$ CMOS technology, the frequency synthesizer occupies the area of $0.92mm^2$ with of-chip loop filter and consumes 36mW from a 1.8V supply. The PLL is completed in less than $8{\mu}s$. The phase noise is -110dBC/Hz at 1MHz offset from the carrier.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.11
• /
• pp.1297-1306
• /
• 2012

This work presents a 77 GHz radar transmitter for the automotive radar system. An integrated 13 GHz frequency synthesizer fabricated using 130 nm RF CMOS process drives a commercial W-band compound semiconductor monolithic multifunction amplifier(MPA), which includes a frequency multiplier by six to generate 77 GHz transmitting signal. The 13 GHz frequency synthesizer includes a high efficiency injection buffer of 4 dBm output power to drive the MPA. The output power of 77 GHz radar transmitter is higher than 13.99 dBm and the magnitude of the reference spur relative to the carrier is -36.45 dBc. The phase noise is -81 dBc/Hz at 1 MHz offset frequency from the carrier.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.7
• /
• pp.1652-1656
• /
• 2014

In this work, we demonstrated a 77 GHz waveguide VCO with transition from WR-12 to WR-10 for anti-collision radar applications. The fabricated waveguide VCO consists of a GaAs-based Gunn diode, a varactor diode, a waveguide transition, and two bias posts for operating as a LPF and a resonator. The cavity is designed for fundamental mode at 38.5 GHz and operated at second hormonic of 77 GHz. The waveguide transition has a 1.86 dB of insertion loss and -30.22 dB of S11 at the center frequency of 77 GHz. The fabricated VCO achieves an oscillation bandwidth of 870 MHz. Output power is from 12.0 to 13.75 dBm and phase noise is -100.78 dBc/Hz at 1 MHz offset frequency from the carrier.

• The Journal of the Acoustical Society of Korea
• /
• v.16 no.4
• /
• pp.76-84
• /
• 1997

In this paper, one of the core components of a mobile communication system, VCO(Voltage Controlled Oscillator) IC is designed. The VCO IC was designed, have realized as LC turned oscillator using varicap. LC sinusoidal tuned oscillator generally requires external inductors and thus remainding circuit is implemneted in monolithic IC. The circuit is fabricated using an 15 mask IC process and has a die size of 1150um${\times}$780um. The tests showed that VCO was operated at frequencies in the regions between 880MHz-915MHz in the control voltage range of 1V to 3V at 5V supply voltage and as the power supply was varied from 4.5V to 5.5V, the frequency varied 425KHz/V. The VCO IC has frequency shift of 1.97MHz/T, carrier level of -7dBm and power consumption of 16.7mA. Also it has phase noise of -80dBc/Hz, offset at 50KHz and harmonic response of center frequency is -41dBm. For the future development of the transceiver 1 chip, the previously mentioned external devices need to be incorporated into Si MMIC.