• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.48 no.6
• /
• pp.27-34
• /
• 2011

In this paper, we propose an active 3D shape acquisition method based on photometric stereo using camera and flash on a smartphone. Two smartphones are used as the master and slave, in which the slave projects illumination from different locations while the master captures the images and processes photometric stereo algorithm to reconstruct 3D shape. In order to reduce the error, the smartphone's camera is calibrated to overcome the effect of the lens distortion and nonlinear camera sensor response. We apply 5-point algorithm to estimate the pose between smartphone cameras and then estimate lighting direction vector to run the photometric stereo algorithm. Experimental result shows that the proposed system enables us to use smartphone as a 3D camera with low cost and high quality.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.3
• /
• pp.392-398
• /
• 1986

It is often occurred that exhaust pipe of an internal combustion engine should be bent due to some geometrical constraints. Especially for automobiles most of exhaust pipes of engines have curvature to avoid rear axles. In this paper effects of pipe curvature on the exhaust noise of a diesel engine have been studied experimentally. Experiments were carried out on a 4-cycle, 2164cc diesel engine. Two types of curvature, circular arc and retangle, were tested. Sound pressure level (SPL) and power spectrum of the exhaust noise were measured by inserting bent pipes of different curvature dimensions into the exhaust pipe at various engine operating conditions. The following results were obtained from this study. Among the engine operating conditions the exhaust noise was affected mainly by engine revolution speed. The noise was reduced by the circular arc bent pipe. The effectiveness of an arc bent pipe on the noise reduction was dominated by its arc angle and the maximum noise reduction was obtained by the angle of 180.deg.. But the noise reduction could not be obtained by the rectangular bent pipe, and at high engine speed the noise was rather increased due to turbulence of exhaust gas.

• Journal of Korean Society of Steel Construction
• /
• v.28 no.5
• /
• pp.337-344
• /
• 2016

In this study, a form-finding method of tensegrity systems by using the force density method combined with the stiffness matrix method was presented. Numerous studies have been made on form-finding methods of the tensegrity systems. However, these methods are limited in the tensegrity systems with multiple null space of the equilibrium matrix. The proposed method can uniquely define a single integral feasible set of force densities for the structures. In order to draw maximum natural frequency that can lead a maximum stiffness of the tensegrity systems, a constrained maximization problem is formulated in the genetic algorithm. Several numerical examples are presented to prove dfficiency in searching for self-equilibrium congifurations of tensegrity systems with multiple self-stress states. A good performance of the proposed method has been shown in the results.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.45 no.3
• /
• pp.226-232
• /
• 2017

Surface pressure distributions over the RAE-A wing-body configuration were investigated and the grid convergence along the streamwise, spanwise, and circumferential directions was numerically studied. Flow analysis in subsonic and transonic conditions was conducted using the $k-{\omega}$ Wilcox-Durbin+ turbulence model. Surface pressure distributions for subsonic flows were well matched, but those for transonic shocked flows showed a little discrepancy with the experimental data. A cubic spline extrapolation method was applied in order to investigate the grid convergence. This method presented that the grid resolution in the circumferential direction is the most important grid parameter. A refined grid system was made based on the grid convergence study and provided more accurate prediction, especially on the symmetric body surface of RAE-A configuration.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.8 no.1
• /
• pp.13-20
• /
• 2006

This study proposes a new concept of a tunnel central drainage system by using a drain board to make a breakthrough on difficulties in the installation of conventional drainage system and draw-down of its drain capacity especially in long tunnels. A fundamental study has been performed for evaluation of the drain capacity of the planar drainage system adopted in this study. In fact, the system proposed makes possible to omit the side, transverse as well as central drainage pipes required in the conventional system, even if its drain capacity and any guideline for design are not available to date. In this circumstance, it is carried out to investigate the correlation between drain capacities and, shapes and posit ions of the columns of the drain board in terms of a variety of water inflows through hydrological model tests. It is shown from the tests that a drain capacity is highly influenced by the shape and the distance between the columns of a drain board in flowing direction, and a round rectangular shape of the columns leads to the highest capacity of drainage. And also, the shorter distance between the columns in flowing direction, the higher drain capacity would be achieved.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.47 no.2
• /
• pp.51-60
• /
• 2010

This paper proposes a new scheme to obtain enhanced 3D shape information rapidly for WLPSI(White Light Phase Shifting Interferometry). WLPSI is a convenient method to measure the height of the micro products. First we propose an effective method of limiting search interval for detecting the peak of the visibility function in order to obtain 3D shpae information rapidly. Second we propose an automatic base level decision method basad on image processing and a correction algorithm using the least square approximation method to overcome the global tilt problem of the conventional WLPSI algorithms. Third we propose an adaptive filtering method to remove the distortion known as bat-wing effect which appears near the step discontinuity. Experimental results show that the proposed overall technique is fast and provides more enhanced 3D shape information compared with the conventional WLPSI algorithms.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.12
• /
• pp.475-481
• /
• 2019

The importance of performance-based design feedback is being emphasized when it comes to the potential impact that affects all the lifecycle of the building. However, the latency and disconnection of domain expert in the sector of AEC/FM remain current obstacles between design and performance feedback. It is hard to utilize performance feedback information for design exploration and support design decision making during the conceptual phase of design. Using parametric design, this paper proposes various design alternatives from a set of rules and constraints defined by algorithms for the geometric configurations of an Office Building. A Building Performance Analysis (BPA) was to developed using Autodesk® Revit® 2019 which integrates Autodesk® Green Building Studio® to predict its sufficient daylighting conditions of the LEED v4's Daylighting Autonomy (DA). The parametric-based performance feedback of this study outlines potential design improvements for further exploration in application to the early design process.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.9
• /
• pp.823-831
• /
• 2011

According to the development of loading equipments, it is usual to change or replace the existing stores. It has been known that pylon-mounted under stores strongly affect aircraft dynamics characteristics due to the change of aerodynamics. To predict the aerodynamics and aero-elasticity is essentially requested with considering the configuration and shape of external stores during the development of aircraft and/or external stores. In this paper, computational fluid dynamics and computational structure dynamics interaction methodology are applied for prediction of aerodynamic characteristics for F-5 aircraft's horizontal tail with various shape of external stores. FLUENT and ABAQUS were used to calculate fluid and structural dynamics. Code-bridge was made base on the globally supported radial basis function to execute interpolation and mapping. As a result, even though the aeroelasticity of the horizontal tail slightly changes according to the shape of external store, the flutter was not occurred at the considered flight conditions in this study.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.10 no.3
• /
• pp.173-180
• /
• 2007

Oscillating wave amplitude in a bottom-mounted OWC chamber designed for wave energy converter is investigated by applying characteristic wave conditions in Korean coastal water. The effects of shape parameters of OWC chamber in a view of wave energy absorbing capability are analyzed. Both experimental and numerical approaches are adopted and their results are compared to optimize the shape parameters which can result in a maximum power production under given wave distribution. The experiment was carried out in a wave flume under 2-D assumption of OWC chamber. The numerical scheme employed a hybrid Green integral equation which adopts the Rankine Green function inside chamber to take account of fluctuating air pressure, while it uses the Kelvin Green function in outer domain. Air duct diameter, chamber width, and submerged depths of front skirt and back wall of chamber changes the magnitude and peak frequency of wave absorption significantly.

• Solar Energy
• /
• v.15 no.1
• /
• pp.53-71
• /
• 1995

Experiments have been conducted on a planar, free surface jet of water to investigate the effects of aspect ratios(AR=6.67, 15, 26.67), average nozzle velocity($V_0=3.3m/s{\sim}78m/s$) and nozzle-to-plate spacings($Z/W=6{\sim}40$) on the characteristics of heat transfer, when 3 rectangular waterjets impinging on a flat plate which has the uniform heat flux. the scondary peaks which produced by circular jets also produced by rectangular water jets. The position of the scondary peaks depends upon the aspect ratio of nozzle. The heat transfer coefficient was subjected to the influence of aspect ratio. The heat transfer correlations and best position of nozzles which produced maximum heat transfer coefficient at stagnation point are provided.