• Journal of the Korean Wood Science and Technology
• /
• v.35 no.3
• /
• pp.22-28
• /
• 2007

Using woodceramics made from sawdust board of pine thinning logs, changes in surface temperature were investigated, by the heating rate and keeping time at maximum temperature. The heating rate of $2^{\circ}C/min$ and keeping time at maximum temperature 1 hour, were the highest in surface temperature. Also, it was found that woodcermics maintained heat for a long time because the descending velocity of their surface temperature was slower than that of the heater.

• Electronics and Telecommunications Trends
• /
• v.12 no.6 s.48
• /
• pp.131-135
• /
• 1997

본 고는 ATM교환기 고온 상태 동작 특성을 시험하기 위하여 온도 조건, 시험 시간, 시험 절차, 시험 방법, 세부 기준, 판정 기준 등을 정한 것으로, 고온 동작 기준은 한국통신 환경 관리기준 및 품질 표준서-4101을 근거로 하였다. 온도 조건은 평균 $49^{\circ}C$를 유지하되 허용편차는 $1^{\circ}C$내외로 시험되어야 하며, 시험 시간은 온도 상승 및 하강 시간과 장애 발생시 고장 조치 시간 등을 포함하여 최대 72시간을 넘지 않아야 하고, 고온 유지시간은 48시간으로 채택한, ATM 교환기 고온 시험 방법과 기준을 제시하였다.

• Resources Recycling
• /
• v.28 no.3
• /
• pp.59-67
• /
• 2019

This study was conducted to fabrication pig iron containing copper and to reduce sulfur content pig iron. Roasting test was conducted for 1 ~ 9 hours at each temperature of $500^{\circ}C$, $700^{\circ}C$, and $900^{\circ}C$. In addition, the effect of oxygen partial pressure with 0.5, 0.8, and 1 atm was carried out for 30 minutes at $900^{\circ}C$. It was found that there is no effect to reduce sulfure in pig iron through roasting and oxygen partial pressures. The addition of CaO with 15 wt.% was found to reduce sulfur content up to 0.001 wt.%. The suitable temperature and reactive time for carbothermic reduction were $1600^{\circ}C$ and 30 minutes which shows the highest recovery rate of iron from the copper slag.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.8
• /
• pp.847-853
• /
• 2011

In this study, a hybrid powder-extrusion process involving the control of temperature dwelling time for improving the formability of Zn-22Al powder was developed and the effect of dwelling time on the mechanical properties of a spur gear with a pitch circle having a diameter of 1.8 mm was investigated. General extrusion experiments were carried out at different temperatures such as 290, 300, and $310^{\circ}C$. Spur gears with good qualities and without any surface defects were obtained in the case of extrusion temperature of $310^{\circ}C$ and ball-milling duration of 32 h. The Vickers hardness distribution was non-uniform, and after the sintering process, an internal crack was generated because of the different deformation energy between gear central part and teeth. To overcome the abovementioned problems, research on controlling the dwelling time of the extrusion temperature in the powder-extrusion process was carried out. Good-quality spur gears were obtained when the dwelling time was 15 min.

• Proceedings of the Korean Society for Bio-Environment Control Conference
• /
• 1999.11a
• /
• pp.59-62
• /
• 1999

1. 미스트를 장시간 분사시킬 경우 분사기간동안 온도강하는 분사량에 무관하게 일정하나 분사종료 후 온도상승은 분사량이 많으면 온도상승이 현저히 지연된다. 반면 증가된 습도는 장시간 유지되기 때문에 적정 분사량이 존재한다. 2. 시설하우스내 고온장애와 습도장애를 극복하고 보다 유리한 실내환경을 유지하기 위해서는 적정 미스트 분무량을 유지시켜야 하며 동시에 분무시간과 휴지시간을 충분히 고려해야만 한다.

• Journal of the Korean Wood Science and Technology
• /
• v.33 no.3 s.131
• /
• pp.38-44
• /
• 2005

This research investigated the variation of density, the weight loss, dimensional shrinkage and heat conduction by the heating rate and keeping time at maximum temperature of woodceramics, when sawdust boards made from thinned logs of Pinus densiflora, Larix kaemferi and Pinus koraiensis were impregnated with phenol-formaldehyde resin, and then were formed by heating rate ($2^{\circ}C/min{\sim}6^{\circ}C/min$) and keeping time at maximum temperature (1~5 h). As the heating rate increased, the density and thickness shrinkage decreased, but weight loss and linear shrinkage increased. The more the keeping time at maximum temperature, the greater the linear shrinkage and thickness shrinkage. The heating conduction was superior at the heating rate is $2^{\circ}C/min$ and the keeping time at maximum temperature of 2 hs.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.08a
• /
• pp.41-46
• /
• 2002

본 논문은 냉, 난방 디지털 온도 조절계(SPC 50)의 Etl의 편차 정 동작에 관한 구현장치 제작과 비례 미.적분기가 At 및 비 At기능에서 설정온도를 $100^{\circ}C$를 유지하는데 기인된 전압전류 및 전력데이터 획득의 요인과 비례미적분 정수 및 노 개선점을 연구하였다. 설정온도를 유지하는 온도변화는 At기능에서 $96.7^{\circ}C\sim102^{\circ}C$ 이며, 비At 기능에서는 $97.6^{\circ}C\sim100.2^{\circ}C$이었다. 온도유지 전압변동은 At기능에서 2V~217V이며, 비 At기능에서 20V~217V 이었다. At와 비 At 기능에서 설정온도 $100^{\circ}C$을 유지하는데 온도를 냉각시키는 환풍기가 온. 오프 되는 시간차는 20초 정도 발생하였다. 온도차 및 전압차는 두 기능간에 비례 미. 적분값 설정이 자동 및 수동이냐에 따라서 차이를 보여주었다. 두 기능에서 설정된 온도값 유지에 따른 전압전류의 승압과 하강의 변동된 변환 데이터는 설정된 온도가 성취되어지는 시간차 및 설정값 유지의 특성을 요인으로 한 PID값과 노의 개선점에 길잡이가 된다.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.10 no.8
• /
• pp.883-890
• /
• 2015

As the semiconductor processing technology has been developing, multiple cores or NoC(network on chip) can be contained in recent chips. GALS(globally asychronous locally synchronous) clocking scheme that has multi-clock domains with different frequencies or phase differences is widely used to solve power consumption and clock skew in a large chip with a single clock. A synchronizer is needed to avoid a synchronization problem between sender and receiver in GALS. In this paper, the setup and hold time of DFF required to design the synchronizer are measured using 180nm CMOS processing parameters depending on temperature, supply voltage, and the size of inverter in DFF. The simulation results based on the bisection method in HSPICE show that the setup and hold time are proportional to temperature, however they are inversely proportional to supply voltage, and negative values are measured for the hold time.

• Food Science and Preservation
• /
• v.15 no.1
• /
• pp.15-20
• /
• 2008

By considering the storage temperatures of agricultural products, three types of PCMs $(K_1$, $K_2$, $K_3$) were developed to be used in temperature ranges of $0{\sim}5^{\circ}C$, $5{\sim}10^{\circ}C$ and $10{\sim}15^{\circ}C$, $K_1$ PCM for $0{\sim}5^{\circ}C$ was developed by mixture of $C_{14}H_{30}$ and soduim polyacrylate, and $K_2$ PCM for $5{\sim}10^{\circ}C$ and $K_3$ PCM for $10{\sim}15^{\circ}C$ were mixture of $C_{14}H_{30}$, $C_{18}H_{38}$ and soduim polyacrylate with different composition ratio. 'The target temperatures of cold chain system were set at $7^{\circ}C$, $13^{\circ}C$, and $17^{\circ}C$ with $K_{1-3}$, $K_{2-3}$ and $K_{3-1}$ PCMs, respectively. The times to reach the target temperatures in the storage chamber were 21 hours, 18 hours, and 61 hours with $K_1$, $K_2$, and $K_3$ PCMs, respectively. The performances of natural convection type and forced convection of the temperature controlled portable container were analyzed Apples were stored in the portable container of $5^{\circ}C$, and temperatures at surface and center were measured. The initial temperature of the apple was $25^{\circ}C$. The temperatures of apple at the surface and the center were $15^{\circ}C$ and $16^{\circ}C$, respectively, after 5 hours with natural convection type. However, the temperatures at the surface and the center were already reached to $7^{\circ}C$ within 1 hour with forced convection type. The forced convection type showed the better performance and the temperatures of portable container were maintained more than 15 hours.

• Proceedings of the Korean Society for Emotion and Sensibility Conference
• /
• 2001.05a
• /
• pp.141-146
• /
• 2001

실내 공기조화를 하는 거주역에 대한 온열환경요소의 자극 변화를 통해 실내 에너지를 절약할 수도 있으며 쾌적감도 향상시킬 수 있다. 따라서 본 연구에서는 거주자의 온열감각을 자극할 수 있는 온열요소 중 비교적 영향이 크고 용이하게 제어할 수 있는 온도 및 기류의 변동으로 한국인의 온열감각(온냉감, 쾌적감, 만족감)에 미치는 영향을 실험을 통하여 파악하였다. 온도 및 기류별 실험을 통하여 22$^{\circ}C$, 24$^{\circ}C$, 26$^{\circ}C$의 각 온도에 대한 패케지 에어컨의 강, 중, 약 기류에 대한 인체순응 시간과 인체 변화를 파악하였다. 또한 인체순응시간을 고려한 온도 상승 실험을 통하여 24$^{\circ}C$, 26$^{\circ}C$에서 1$^{\circ}C$온도 상승시 인체의 온열쾌적감의 변화를 파악하였으며 온도 상승을 통한 인체 순응시간을 도출하였다. 본 실험을 통하여 초기공조 조건을 24C$^{\circ}C$ 로 한 경우 인체순응을 통한 온도 상승으로 30분 후의 공조중기와 공조후기에 온도 및 기류의 지속적인 변동 자극으로 온냉감은 "약간 서늘하다"를 지속적으로 유지하고 있으며 온도상승으로 인한 쾌적존의 높은 온도에서도 기류의 영향으로 쾌적감은 30분 이후부터 "쾌적"을 지속적으로 유지하는 것을 알 수 있었다. 따라서 본 연구를 통하여 인체순응을 고려한 온도 및 기류의 자극을 통하여 공조초기부터 공조말기의 장시간에도 인체가 지속적인 쾌적성을 유지한다는 것을 알 수 있었다.성을 유지한다는 것을 알 수 있었다.