• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.4
• /
• pp.164-172
• /
• 2020

The fuel oil/heat exchanger installed in military aircraft is a device that cools the lubricant oil supplied to other devices, such as an AMAD, and a hydraulic pump using the low temperature of the fuel is cracked at the AMAD lubricant inlet port. If a crack in the heat exchanger occurs, the lubricant oil supplied to other equipment is not cooled. Therefore, the flight can no longer be performed. In this study, non-destructive inspection and microscopic examination of the fracture surface of the oil port were performed to analyze the crack tendency. The oil pipe connected to the oil port is a titanium pipe, which is fastened with over torque and has been identified as the leading cause of heat exchanger oil port cracks. In addition, it was verified as the main reason for cracking by finite element analysis. The material and diameter of the pipe were changed to improve this defect, and the applied torque was adjusted. In addition, the bending value of the pipe was adjusted to minimize the fatigue accumulation due to pulsating pressure. As a result, no cracks occurred on the heat exchanger via the ground test after the installation of an improved pipe under the same conditions.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.2
• /
• pp.129-136
• /
• 2010

Axial piston pumps have been widely used as power sources for hydraulic systems, but studies on the fluid flow within the pump have been usually performed using 1-D analysis because of the difficulties in considering the fluid compressibility, high-speed revolution, variation of the flow rate, and complicated geometry. The goal of this study was to understand the hydraulic fluid flow within axial piston pumps by using the 3-D numerical method and the process of generating discharge pressure ripples. To improve the convergence and robustness of the simulation model, a grid system was constructed with hexahedron-type grids around the valve plate. Furthermore, we employed an empirical formula to describe the relationship between the oil density and pressure. The CFD (computational fluid dynamics) results compared well with the experimental data.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.12
• /
• pp.1237-1244
• /
• 2015

A gerotor can be manufactured in a miniature size because it has a high discharge per cycle and a simple structure. Gerotors are widely used for the lubrication oil of an engine and as the hydraulic source of an automatic transmission. Recently, improvements in fuel efficiency and noise reduction have come to the fore in the automobile industry, and it has been necessary for better fuel efficiency to continuously improve the flow rate and noise of internal gear pumps through the optimal design of the gerotor and port shape. In this study, gerotors were generated based on the equations derived for a lobe shape with multiple profiles (ellipse 1-elliptical involute-ellipse 2). The ranges of the design parameters were considered to prevent a cusp and loop. In addition, the optimal lobe shape was obtained by determining the influence of the lobe shape on the performances (flow rate, irregularity, etc.), according to the values of the design parameters.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.120-120
• /
• 2018

반도체 소자나 디스플레이 패널 제조 공정에 가장 많이 사용되는 진공 펌프인 터보 분자 펌프는 오일을 사용하지 않고, 설치 방향이 자유로우며 넓은 작동 압력 영역을 가지고 있어서 고가임에도 불구하고 점점 더 사용 영역을 넓혀 가고 있다. 상하의 두 곳에 회전축을 지지하는 베어링이 필요한데, 기계식 금속 베어링을 채용하는 경우에는 반드시 윤활유를 공급해 주어야 하고, 고온, 부식성 또는 산화성 가스의 배기 시에는 퍼지 가스로 비활성인 질소나 알곤등을 이용하여 보호를 해주어야 한다. 반면, 자기 베어링을 채택한 모델은 윤활의 걱정에서 자유로울 수 있기 때문에 채용이 늘어나고 있다. 동일극의 반발력이나 반대극의 인상력을 이용한 구조를 갖게 되는데 갑작스러운 입구 쪽 압력의 증가 시에는 자석 끼리 부딪치는 일이 발생하고 이로 인해서 로터 모듈 전체에 큰 손상을 갖게 되므로 한 곳 정도에 비상용 터치 다운 베어링을 기계식으로 윤활제 없이 설치하기도 한다. 기본적으로 자기 베어링 방식은 로터 모듈의 부상과 제어를 위해서 3축 또는 5축 제어를 하게 되는데 여기에는 전자석의 전류를 미세하게 조정하여 피드백 하는 시스템을 활용하기 때문에 외부에서의 자기장이 일정값 이상 침투하게 되면 제어 회로의 기능에 문제를 일으키게 된다. 또한 축 방향에 수직인 자기장의 강도가 높아지면 고속으로 회전하는 금속 블레이드가 자속을 자르게 되므로 표면에 와전류가 발생하여 문제가 된다. 터보 분자 펌프는 회전자와 고정자 간격이 1 mm 이내로 작아서 약간의 진동이라도 발생하면 회전자와 고정자 간에 충돌이 일어나고 이는 곧 파손으로 이어진다. 그림 1에는 파손 원인 분석을 위한 회전자 모듈의 수치 해석용 모델의 일부를 나타내었고, 그림 2에는 실제로 외부 자기장에 의한 파손이 발생한 사례의 자기 베어링 모듈의 사진을 나타내었다. 본 발표에서는 외부 자기장의 형태에 따라 제어 자기장에 미치는 영향을 CFD-ACE+(ESI corp)를 활용하여 해석하였다.

• Journal of the Society of Disaster Information
• /
• v.17 no.1
• /
• pp.112-119
• /
• 2021

Purpose: This study is based on the detailed inspection data for the last 6 years of fire-fighting high ladder vehicles, fire-fighting inflected ladder vehicles, fire-fighting chemical vehicles and fire-fighting pump vehicles used in front-line fire departments. The purpose is to contribute to the technological development of fire-fighting vehicles by grasping the implementation status of each city and province, the rate of defects, and the occurrence of defects by year. Method: The implementation status by city and province, defect incidence rate, and defect occurrences by year were analyzed. Result: From 2012 to 2017, when the average of 230 or more overhaul vehicles was requested, the results of each city/province show slight fluctuations, but the number of defects gradually decreased due to the old fire-fighting vehicle replacement project and the response of fire vehicle manufacturers. Conclusion: In the case of fire-fighting ladders, the incidence rate of defects was found to be in the order of elevator device, electric device, ladder device, and pneumatic supply device. And in the case of the fire fighting ladder, it was confirmed that the incidence of defects appeared in the order of the refractive ladder, hydraulic cylinder, hydraulic oil, and pneumatic supply device. In the case of fire-fighting chemical vehicles, it was confirmed that defects occurred in the powder fire extinguishing device, fire pump, vacuum pump, and pneumatic supply device.

• Journal of the Korean Society for Precision Engineering
• /
• v.33 no.3
• /
• pp.207-216
• /
• 2016

A gerotor is suitable for miniature manufacturing because it has high discharge per 1 cycle and a simple structure, while also being widely used for lubrication oil of engines and as a hydraulic source of automatic transmission. In the automobile industry, improvements in fuel efficiency and noise reduction have recently come to the fore. It has also been necessary to continuously improve the flow rate and noise of internal gear pumps for better fuel efficiency through optimal gerotor and port shape design. In this study, to develop an optimal gerotor with a new lobe shape, 2-ellipses-combined, the equation of the lobe shape was derived, and CFD analysis results were compared for 2-ellipses with those of the previous gerotors (3-ellipses and ellipse1-involuteellipse2). A performance test for the oil pump with the optimal rotor (2-ellipses) was carried out and showed good agreement with the results obtained from CFD analysis.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2009.05a
• /
• pp.255-256
• /
• 2009

The anti suck back centering (ASBC) for preventing backflow of oil for oil rotary pump was designed in the power failure. To evaluate the evacuation characteristics, we manufactured the mini vacuum system, personal computer, AD converter (National instrument, NI-6009), and automatic controller with touch panel for a basis. In this study, we measured the evacuation characteristics of ABSC and analyzed the flow field of viscous flow regime using a commercial software, CFD-ACE+. Also, the leakage of the advaced ASBC for leveling was measured.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.6 no.1
• /
• pp.10-16
• /
• 2009

Automatic power transmission systems consisted of a torque converter and several planetary gear sets, clutches and brakes are controlled by a hydraulic shift control circuit and an electronic transmission control unit. The hydraulic circuit serves for the operation of the torque converter and lubrication oil supply of the transmission system as well as for the actuation of clutches for the automatic gear shift. The complicated hydraulic control circuit constructed by many spools, solenoids, orifices and flow passages are integrated into one small valve block and it is powered by one hydraulic pump. In this paper, a test equipment was developed to measure the oil consumption of each component at various wide operating conditions. Test data about 730 sets acquired from five test items are analyzed and discussed on the oil capacity of the circuit.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.25 no.3
• /
• pp.168-172
• /
• 2013

A preliminary performance test of a 30RT 2-stage screw heat pump was carried out in order to develop a high performance large-scale unutilized energy source heat pump system, which will be used for district heating and cooling. In this study, two issues of the system operating control were investigated. The first issue is the mode switching control from 1-stage to 2-stage. A stable 2-stage heating operation is guaranteed, only if the load-side water inlet temperature is over a certain value, where the 1-stage heating operation should be done first from a cold start. The second issue is oil level control. An oil shortage problem in the low stage compressor, which depends on the degree of suction superheat, was solved by a proper oil level control scheme.

• Journal of the Korean Applied Science and Technology
• /
• v.31 no.4
• /
• pp.688-693
• /
• 2014

This study is to increase the utilization of the ozonated water generator to make it easier to take advantage of the ozone water in the world today, there will be to develop a system that operates in one motion. Furthermore, olive oil and ozone is reacted with the wish to apply to the manufacturing technology. In the case of many existing products ozone generator driven mostly non-ozone system. In the case of ozone, but handwriting is implied general way pressure ozone gas leakage risks of suction force to the pump, it is the case of the challenge by using the injector, and limit the generation of ozone and ozone inhalation according to whether the water inlet leakage of existing products risk due to minimized. Despite the disadvantages of the injector system was found the effectiveness of the ozonated water production unit injector system used in this study to maintain the microbiological disinfection performance.