• Journal of Welding and Joining
• /
• v.5 no.1
• /
• pp.16-22
• /
• 1987

오스테나이트계 스테인레스강 용접부의 .delta.-페라이트 생성인자에 관한 위의 실험결과로부터 아래의 결론을 얻을 수 있다. (1) 오스테나이트계 스테인레스강 용접부의 .delta.-페라이트는 에너지적으로 불안정한 상으로서, 오스테나이트로의 변태가 비가역적(irreversible)이다. (2) .delta.-페라이트의 생성 및 변태에는 합금원소의 확산이 반드시 수반되며, 최종 .delta.-페라 이트 함량은 정성적으로 다음과 같이 표시된다. 페라이트함량=primary페라이트-변태한 페라이트 (3) .delta.-페라이트 생성에 일차적으로 영향을 미치는 이자는 화학조성(Cr-당량/Ni-당량)이며, primary 변태양상 및 냉각속도에도 크게 의존한다. (4) 용착부 .delta-페라이트는 대개 Vermicular와 Lathy의 혼합조직으로 존재하며, 열영향을 받 을수록 에너지적으로 안정한 Globuar 형상으로 변해간다.

• Journal of Power System Engineering
• /
• v.16 no.4
• /
• pp.60-65
• /
• 2012

This study was carried out to investigate the effect of reverse transformation on the damping capacity in high manganese austenitic stainless steel. ${\alpha}^{\prime}$-martensite was formed with the specific direction and surface relief by deformation. Over 95% of the austenite phase was transformed to deformation-induced ${\alpha}^{\prime}$-martensite by 70% cold rolling. Reverse transformation became rapid above an annealing temperature of $550^{\circ}C$, but there was no significant transformation above $700^{\circ}C$. In addition, with increasing annealing time at $700^{\circ}C$, reverse transformation was induced rapidly, but the transformation was almost completed at 10 min. Damping capacity was increased up to $700^{\circ}C$, and than unchanged with the increasing annealing temperature. Damping capacity increased steeply with an increasing reverse treatment time up to 10min, whereas there were no significant change with a treatment time of more than 10 min. Damping capacity increased with an increasing the reversed austenite and was strongly affected by reversed austenite.

• Journal of Power System Engineering
• /
• v.16 no.3
• /
• pp.51-56
• /
• 2012

The effect of deformation induced martensite transformation on the mechanical properties in austenitic stainless steel with high Mn was studied. ${\alpha}$'-martensite was formed by deformation in austenitic stainless steel with high Mn. Deformation induced ${\alpha}$'-martensite was formed with surface relief by cold rolling. With the increase of deformation degree, volume fraction of deformation induced martensite was increased rapidly in early stage of deformation and then, increased slowly. With the increase of deformation degree, hardness and tensile strength were rapidly increased with linear relations, while elongation was rapidly decreased and then slowly decreased. Hardness, tensile strengths and elongation were influenced strongly by deformation induced martensite.

• Journal of Welding and Joining
• /
• v.10 no.1
• /
• pp.12-19
• /
• 1992

용접능률의 향상을 위한 대입열용접법의 적용은 과도한 입열량으로 인하여 용접부의 인성이 저 하한다는 점에서 그 적용에 주의를 요한다. 본 보에서는 대입열용접시 열영향부의 인성 저하의 원인과 그 대책을 강재의 측면에서 검토하였다. 고장력강을 용접하면 입열량이 증가함에 따라 오스테나이트 결정립이 조대화되고 상부 베이나이트와 도상 마르텐사이트가 생성되어 인성이 저하한다. 그 대책으로서는 용접 열싸이클과정중 안정한 질화물, 산화물등을 모재에 미세분산시켜 오스테나이트 결정립 성장을 억제하고, 페라이트, 펄라이트 변태를 촉진시킨다. 이러한 석출물의 형성을 위해서는 주로 Ti, Ca, REM, B등의 합금원소가 이용된다. 소입성이 높은 주질고장력 강에서는 석출물의 분산에 의한 페라이트의 변태 촉진 보다는 Mn, Ni, Cr, Mo, V등의 합금원 소를 첨가하여 소입성을 높여 인성이 우수한 하부 베이나이트 조직을 형성하든가, 탄소량을 저 감시켜 도상 마르텐사이트의 생성을 억제하므로서 인성을 확보한다. 현재 국내에서 제조되고 있는 대입열용접용강중 인장강도 50kgf/mm$^{2}$급강은 기본적으로 용접부 인성이 우수한 TMCP법으로 제조되며, Ti등을 첨가하여 석출물의 효과를 이용하고 N을 억제하여 기지의 인 성을 향상시키는 등의 방법을 병용하고 있다. 인장강도 60kgf/mm$^{2}$ 급강은 조질처리에 의하여 제조되며, 50kgf/mm$^{2}$급강과 같이 Ti, B등의 첨가에 의한 석출물의 효과를 이용 하고 있다.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.61-61
• /
• 2018

듀플렉스 스테인리스강은 페라이트와 오스테나이트 상이 공존하는 특징을 갖는다. 그러한 구조에 의해서 페라이트와 오스테나이트상의 장점을 동시에 갖는 특성이 있다. 높은 강도와, 우수한 내식성, 응력 부식 균열 그리고 낮은 니켈의 함량 때문에 안정적인 가격을 갖는 장점을 갖기 때문에 운송, 기름과 가스, 해양플랜트, 건축 그리고 높은 강도와 우수한 내식성이 필요한 분야에서 수요가 증가할 것으로 사료된다. 이러한 듀플렉스 스테인리스강의 형성에서 페라이트와 오스테나이트상의 균형과 내식성을 개선하기 위해 질소가 첨가된다[1,2]. 본 연구는 저니켈 듀플렉스 스테인리스강(STS 329 FLD)의 공식 형성 과정에서 질소의 함량이 공식 형성과 내식특성에 미치는 영향을 동전위분극, XPS(X-ray Photoelectron Spectroscopy) 그리고 GDOES(Glow Discharge Optical Emission Spectrometry)를 이용하여 규명하였다. GDOES를 이용하여 깊이별 원소 분포를 정량적으로 비교한 결과, 부동태막에서 질소는 기저에 비하여 증가하였고, 질소의 함량이 증가함에 따라 wt.% 또한 증가하였다. 이러한 부동태막의 깊이별 원소 분포특성이 내식특성과 공식의 크기에 미치는 영향을 동전위분극을 이용하였다. 질소의 함량이 증가하였을 경우, 부식전위는 증가하였으며, 부식전류는 감소하였다. 또한 부동태전류가 감소한 것을 확인할 수 있었다. 이러한 차이의 원인을 확인하기 위하여 XPS를 이용하여 질소의 화학적 상태를 확인하였다. 질소는 암모니아의 형태로 존재하는 것으로 확인되었다. 암모니아 상태로 부동태막에 존재함에 따라 공식이 형성될 때, 암모늄 화함물을 형성하여 공식 내부의 산성도를 낮춤으로써 공식의 형성이 억제된 것으로 사료된다. 또한 공식 이후의 표면을 관찰 할 경우 질소의 함량이 증가함에 따라 표면에서 공식이 거의 관찰되지 않았다.

• Journal of Ocean Engineering and Technology
• /
• v.26 no.3
• /
• pp.55-60
• /
• 2012

This study was carried out to investigate the effect of the deformation temperature in high manganese austenitic stainless steel. ${\alpha}$'-martensite was formed with a specific direction by deformation. The volume fraction of the deformation induced martensite was increased by increasing the degree of deformation and decreasing the deformation temperature. With the increase in the deformation, the hardness and tensile strength were increased, while the elongation was rapidly decreased at the initial stage of the deformation, and then gradually decreased. The hardness and tensile strength were increased and the elongation was decreased with adecrease in the deformation temperature. The hardness and tensile strength were strongly controlled by the volume fraction of martensite, but the elongation was controlled by the transformation behavior of the deformation induced martensite.

• Journal of the Korean Institute of Gas
• /
• v.2 no.1
• /
• pp.7-13
• /
• 1998

In this study, for the safety performance of LNG storage tank, the fracture toughness in X-grooved weld HAZ(heat-affected zone) of $9\%$ Ni steel was evaluated qualitatively and quantitatively, and the relation with the change in microstructure was analyzed. The toughness assessment was peformed through the modified CTOD test proposed for thick weldment with X-groove. Additionally, microstructures of HAZ were evaluated by OM, SEM and XRD. From the results, HAZ toughness of SMA(shielded metal arc)-welded $9\%$ Ni steel decreased as the evaluated region approached the fusion line. The decrease in toughness was apparently caused by the increase in the fraction of coarse-grained zone within HAZ. On the other hand, toughness drop with decreasing test temperature in F.L.(fusion line) ${\~}$F.L.+3mm was larger than that in F.L.+5mm${\~}$F.L.+7mm region due to the fact that in the former regions, retained austenite had poor stability.

• Journal of Powder Materials
• /
• v.25 no.2
• /
• pp.126-131
• /
• 2018

In the present study, we investigate the effects of milling time and the addition of a process control agent (PCA) on the austenite stability of a nanocrystalline Fe-7%Mn alloy by XRD analysis and micrograph observation. Nanocrystalline Fe-7%Mn alloys samples are successfully fabricated by spark plasma sintering. The crystallite size of ball-milled powder and the volume fraction of austenite in the sintered sample are calculated using XRD analysis. Changes in the shape and structure of alloyed powder according to milling conditions are observed through FE-SEM. It is found that the crystallite size is reduced with increasing milling time and amount of PCA addition due to the variation in the balance between the cold-welding and fracturing processes. As a result, the austenite stability increased, resulting in an exceptionally high volume fraction of austenite retained at room temperature.

• Journal of Powder Materials
• /
• v.27 no.5
• /
• pp.414-419
• /
• 2020

In the present study, we investigated the austenite stability of a sintered Fe-based nanocrystalline alloy. The volume fraction of austenite was measured based on the X-ray diffraction data of sintered Fe-based nanocrystalline alloys, which were prepared by high-energy ball milling and spark plasma sintering. The sintered alloy samples showed a higher volume fraction of austenite at room temperature as compared to the equilibrium volume fraction of austenite obtained using thermodynamic calculations, which resulted from the nanosized crystalline structure of the sintered alloy. It was proved that the austenite stability of the sintered Fe-based alloy increased with a rise in the amount of austenite stabilizing elements such as Mn, Ni, and C; however, it increased more effectively with a decrease in the actual grain size. Furthermore, we proposed a new equation to predict the martensite starting temperature for sintered Fe-based alloys.

• Journal of Powder Materials
• /
• v.29 no.6
• /
• pp.517-522
• /
• 2022

We investigate the austenite stability in nanocrystalline Fe-7%Mn-X%Mo (X = 0, 1, and 2) alloys fabricated by spark plasma sintering. Mo is known as a ferrite stabilizing element, whereas Mn is an austenite stabilizing element, and many studies have focused on the effect of Mn addition on austenite stability. Herein, the volume fraction of austenite in nanocrystalline Fe-7%Mn alloys with different Mo contents is measured using X-ray diffraction. Using a disk compressive test, austenite in Fe-Mn-Mo alloys is confirmed to transform into strain-induced martensite during plastic deformation by a disk d. The variation in austenite stability in response to the addition of Mo is quantitatively evaluated by comparing the k-parameters of the kinetic equation for the strain-induced martensite transformation.