• Journal of the Korean Institute of Gas
• /
• v.18 no.4
• /
• pp.13-20
• /
• 2014

In natural gas distribution system, gas pressure is regulated correspond to requirement using throttle valve which is releasing huge pressure energy as useless form. The waste pressure can be recovered by using turbo machinery devices such as a turbo expander. In this process, excessive temperature drop occurs due to Joule-Thompson effect during the expansion process. Installing natural gas boiler before or after the turbo expander prevents temperature drop. Fuel cell or gas engine hybrid system further improve the efficiency, but 1~2% of total transporting natural gas is used for operating the hybrid system. In this study, a heat pump system is proposed as a preheating device which can be operated without using transporting natural gas. Thermodynamic analysis on evaporating and condensing temperatures and refrigerants is conducted. Results show that R717 is proper refrigerant for the hybrid system with high COP and low turbine work within the defined operating conditions. In domestic usage in Korea, the heat pump system has more economic feasibility owing to natural gas being imported with a high price of LNG form.

• Applied Biological Chemistry
• /
• v.27 no.2
• /
• pp.55-63
• /
• 1984

Lethal effect on Chinese radish Kimchi was investigated by using a pilot scale Kimchi pasteurizer. A simulation model was presented so as to predict the change in viable cell concentration of the Kimchi during pasteurization. D values of microorganisms in the Kimchi were found to be 2.21, 1.62, 0.73, 0.39 and 0.21min at 60, 64, 70, 75 and $80^{\circ}C$, correspondingly, and thereby z value was $19^{\circ}C$. One cycle time required was 0.99min at flow rate of 4 l/min. The ratio of lethality in preheating section to total lethality was 0.3 and the ratio of lethality in holding, precooling and cooling sections to total lethality was 0.7. The experimental data were in good agreement with the values simulated by two model equations to which linear and exponential temperature profiles were applied at $65^{\circ}C\;and\;70^{\circ}C$ in holding section.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.5
• /
• pp.2069-2074
• /
• 2013

The use of the electromagnetic clutch water pump for internal combustion engine vehicles saves fuel and leads to a reduction in emissions. The clutch water pump allows the engine cooling system to select the optimum operation condition by using coolant flow rate on/off control. This study investigated the characteristics of fuel consumption and emissions of the diesel engine cooling system using the clutch water pump. The electromagnetic clutch operation reduced by about 49% of engine warm up period at idle condition and controlled the optimum high coolant temperature at driving condition. Therefore, fuel consumption was enhanced by about 5%, and emissions such as HC, CO and $CO_2$ were also reduced to a certain degree even though NOx increased a little bit, compared to those of the conventional water pump under NEDC mode which represents the real driving pattern.

• Journal of the Korean Institute of Gas
• /
• v.18 no.2
• /
• pp.28-34
• /
• 2014

In the natural gas pressure regulation station, high pressure natural gas is decompressing using pressure regulation valves. Waste pressure occurred in the pressure regulation process can be recovered through adopting turbo expanders. However, in the waste pressure recovery process, Joule Thompson effect causes below $0^{\circ}C$ and this low temperature freezes outside land of pipeline or generates methane hydrate in the pipeline which can block the pipeline. Therefore, turbo expander systems are accompanying with a boiler for preheating natural gas. Molten carbonate fuel cell (MCFC), one of the high temperature fuel cell, can use natural gas as a direct fuel and is also exhausting low emission gas and generating electricity. In this paper, a thermodynamic analysis on the hybrid MCFC-turbo expander system is conducted. The fuel cell system is analyzed for the base load of the hybrid system.

• Proceedings of the Korean Institute of Resources Recycling Conference
• /
• 2004.05a
• /
• pp.109-113
• /
• 2004

In this study, we tried to develop the moveable instrument for fuel of cement production by using waste plastics from agriculture that was not recycled. First we investigated the burning character of recycled fuel and feasibility of second pollution. Then we made the instrument which can produce the solid fuel under 1cm size. In changing the inputting method from pre-heater to main burner, this reduces the NOx and O2 emission rate. and When we input it 0.5ton/hour, we obtain 0.2-0.3 ton/hour reduction of coal amount.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.47 no.6
• /
• pp.453-458
• /
• 2002

High temperature sterilization method (30min. at $40^{\circ}C$longrightarrow30 min. at $70^{\circ}C$longrightarrow30 min. cooling at $20^{\circ}C$) was evaluated better than that of chloride, ion water, $O_3$ water, and salt water for the controling of micro-organisms at the early stage of sprout culture. Due to the improved germination rate and effective control of micro-organisms at early stage, the method resulted in much lower in the number of micro-organisms, higher in sprout yield, and 2 days longer in quality keeping at market than sprouts prepared by conventional method. There are two methods related with water temperature; constant temperature method (18.5$\pm$ $0.5^{\circ}C$) which keeps the same water temperature during the culture and 3-stage temperature method which changes the water temperature depending on the days after culture. Three-stage temperature method set the temperature at 21$\pm$ $1^{\circ}C$) in the second and third days after the initial acceleration of germination (about 4 hours), at 18.5$\pm$0.5$^{\circ}C$ in the fourth and fifth days, and at 17.0$\pm$ $0.5^{\circ}C$) in the sixth and seventh days. Three-stage temperature method could enhance the resistance power to diseases at the early growth stage, control the growth to standard goods (8-9cm in length and 2.15-2.30mm in width), and keep good body color at the middle or final stage. This method also increased the sprout yield by 6% compared with the conventional method, constant temperature method.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.3
• /
• pp.259-268
• /
• 2012

This study measured the natural-convection heat transfer of two vertically staggered cylinders with varying vertical pitch-to-diameter ($P_v$/D) and horizontal pitch-to-diameter ($P_h$/D) ratios. The measured heat-transfer rates for the lower cylinder agreed well with the existing heat-transfer correlations for a single cylinder. At the smallest $P_v$/D, the rising plume from the lower cylinder provides the upper cylinder with a preheated flow, and the heat-transfer rates of the upper cylinder decrease, but increase very sensitively with $P_h$/D. However, at the largest $P_v$/D, the velocity effect dominates, and the heat-transfer rates of the upper cylinder are larger than that of a single cylinder, and decrease less sensitively with $P_h$/D. Even if $P_h$/D is increased, the heat-transfer rate of the upper cylinder is higher than that of the lower cylinder because of the chimney and side flow effects. This work expanded the flow ranges to turbulent flows. The cupric acid-copper sulfate ($H_2SO_4-CuSO_4$) electroplating system was adopted for the measurements of the mass-transfer rates instead of the heat-transfer experiments based on the analogy concept. The measurements were made by varying $P_v$/D (1.02-5) and $P_h$/D (0-2) in both laminar and turbulent flows. The Rayleigh number ranged from $1.5{\times}10^8$ to $2.5{\times}10^{10}$, and the Prandtl number was 2,014.

• Korean Journal of Food Science and Technology
• /
• v.36 no.2
• /
• pp.226-232
• /
• 2004

Dilution concentration of watermelon juice, concentrations of added sugar, citric acid, and vitamin C, sterilization temperature and time, and natural color extracts were evaluated to determine optimum conditions for watermelon beverage production. Optimum dilution concentration of watermelon juice and optimum content of soluble solid were 40% and $12^{\circ}Brix$, respectively. Addition of 0.5 and 0.3 g/L or 1.0 and 0.3 g/L citric acid and vitamin C gave optimum sensory quality. Sterilization of watermelon beverage at above $70^{\circ}C$ decreased redness. Sterilization at $60^{\circ}C$ for 10 to 30 min or at $70^{\circ}C$ for 10 min achieved best sensory quality. Addition of 20 g/L raspberries gave best sensory quality among raspberries, omija, and borage. Hot water was better than alcohol for extraction of natural color. Ratio of extracts for optimum sensory quality was 7 : 3 for extract of 20 g raspberries/L : extract of 30 g omija/L.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.79-79
• /
• 2010

다른 물질에 비해 많은 우수한 특성을 가지고 있는 CuInSe2(CIS)박막 태양전지는 많은 연구자들에 의해 개발되어 오고 있다. CIS의 대표적인 장점으로는 직접천이형 밴드갭, 높은 흡수계수, 열 안정화상태 및 p형으로의 전도성물질의 가능성 등 다양하다. 또한 간단한 구조를 이용하여 유리같은 싼 기판을 이용하기 때문에 저가형 태양전지로서 많은 각광을 받고 있다. CIGS태양전지는 CIS의 In 사이트에 Ga을 도핑함으로서 만들어지는데 밴드갭은 약 1.4eV이다. CIS박막을 만드는 많은 방법이 존재하나 구성원소로부터 최적화된 조성을 찾을수 있는 방법이 가장 중요한 요소 중의 하나로 인식되고 있으며, 이런점에서 증발법 및 스퍼터링법 등 같은 진공방식이 비진공방식에 비해 훨씬 간편하게 조성비를 맞출수 있다. 그 중에 스퍼터링법은 대면적 박막태양전지로의 가능성으로 비출어 볼때 산업화를 위한 좋은 후보군이 될 수 있다. Selenization을 하기전에 Cu-In-Se의 전구체 조합은 여러개의 타겟으로부터 동시 스퍼터링법이나 다층 전구체법을 사용하여 준비되는데 어떤 방법이 되던지 Se의 부가적인 공급은 불가피하다. 지금까지 많은 관련 연구의 대부분인 구조적, 조성비적 그리고 광학적인 특성평가에 집중되어 오고 있는데, 전기적특성평가의 경우는 면저항, 비저항 같은 간단한 결과 위주로 보고되어 오고 있다. 또한 캐리어농도와 이동도에 대한 보고가 있음에도 불구하고 이해되기에는 충분치 못한 면이 많다.본 발표에서는 태양전지 제조 전단계로서 소다라임유리기판(SLG)위에 Mo의 유무에 따라 CIS박막의 전기적인 특성 변화에 대한 내용을 담고 있다. 소다라임유리($2cm{\times}2cm$)를 기판으로 사용하여 아세톤-에탄올 용액에 초음파세척을 수행하고, Mo 후면전극을 DC 스퍼터링방식을 이용하여 증착을 한다. SLG와 Mo이 코팅된 SLG를 각각 RF 스퍼터 챔버에 이송한 후 수증기 제거를 위해 약 10분간 예열을 한다. 샘플에 대한 전기적특성은 Hall효과 측정장치에 의해 측정이 되며 전기전도도, 캐리어농도, 이동도 및 전도형에 대한 정보가 각각의 변수에 따라 조사된돠. 부가적으로 구조적, 조성비적인 특성을 SEM,XRD 및 EDX를 통해 조사를 하여 전기적 특성에 따른 관계성을 검토한다. SLG와 Mo가 코팅된 SLG위의 CIS박막은 전기적으로 약간 다른 특성을 보일 것으로 예측되며, 이러한 기대를 바탕으로 조성비가 이상적인 화학양론에 근접할 때 p형으로서 제시될 수 있다는 것을 보여줄 것이다.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.36 no.4
• /
• pp.329-336
• /
• 2000

Welding is a important technological method in mechanical engineering. $CO_2$MAG(metal active gas) welding means that metal part in double capstan drum for the inshore and costal vessels are joined by melting(with or without a filler material) or that new material is added to a metal part by melting. The thermal stresses appear due to a non-uniform temperature field, inhomogeneous material properties, external restraint and volume changes during phase transformations. In this study analysis the elasto-plastic thermal stresses distribution of welding part in double capstan drum for the inshore and costal vessels using finite element method (FBM). Therefore it calculates the numerical value that can be applied to the optimum design of welding parts and the shapes. The significant results obtained in this study are summarized as fellows. At early stage of the cooling after welding process, the abrupt thermal stresses gradient has been shown in the vicinity of welding part. In the thermal stresses analysis due to temperature gradient and heat shocking maximum stress was occurred of welding part and stresses were distributed from 54MPa~48MPa.