• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.44 no.2
• /
• pp.133-139
• /
• 2018

Chemically damaged hair is vulnerable to external stimuli in daily life due to the weakened physical properties of the hair strand itself. The purpose of this work was to determine whether chemical conjugation between hair keratin proteins restores tensile strength and thus results inpreventing further deterioration under repeated combing. A model damaged hair tress was produced by a typical perm-process. Then, it was internally crosslinked by the bifunctional crosslinker (3-aminopropyl)triethoxysilane (APTES), via both silane coupling and carbodiimide chemistry. Physical properties, including tensile strength, Young's modulus, and plateau stress, were measured to verify the effect of internal crosslinking, and the existence of crosslinking was verified by Fourier transform infrared (FT-IR) spectroscopy. The degrees of hair breakage and split ends were evaluated by repeated combing-drying tests. Physical properties of chemically damaged hair were restored by internal crosslinking. Successful crosslinking of APTES via both silane coupling and carbodiimide chemistry was verified by FT-IR spectra. Prevention of breakage and split ends after repeated combing with heat was observed. Human hair can be weakened by chemical damage including perm-processing, so restoring such properties is a major issue in the hair care industry. This work shows that internal crosslinking of damaged hair via chemical conjugation would be a potent method to restore the healthy hair.

• Journal of the Korean Ceramic Society
• /
• v.40 no.9
• /
• pp.874-880
• /
• 2003

The effect of h-BN content on microstructure, mechanical properties, and machinability of AlN-BN based machinable ceramics were investigated. The relative density of sintered compact decreased with increasing h-BN content. The four-point flexural strength also decreased from 238 MPa of monolith up to 182 MPa by the addition of 30 vol％ h-BN. Both low Young's modulus and residual tensile stress, formed by the thermal expansion coefficient difference between AIN and h-BN, might cause the strength drop in AlN-BN composite. The crack deflection, and pull-out phenomena increased by the plate-like h-BN. However, the fracture toughness decreased with h-BN content. The second phases, consisted of YAG and ${\gamma}$-Al$_2$O$_3$, were formed by the reaction between Al$_2$O$_3$ and Y$_2$O$_3$. During end-milling process, feed and thrust forces measured for AlN-(10～30) vol％ BN composites decreased with increasing h-BN particles, showing excellent machinability. Also, irrespective of h-BN content, relatively good surfaces with roughness less than 0.5 m (Ra) could be achieved within short lapping time.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.123-123
• /
• 2010

3족 질화물계 물질은 발광다이오드와 같은 광전자소자적용에 있어서 매우 우수한물 질이다.일반적으로, GaN 에피 성장에 있어서 저온 중간층을 삽입한 2 단계 성장 방법은 낮은 결함밀도와 균일한 표면을 얻기 위해 도입된 기술이다. 특히 AlN 중간층은 GaN 중간층과 비교하였을 때 결정성뿐만 아니라 높은 온도에서의 열적안정성, GaN 기반의 자외선 검출기서의빛 흡수 감소 등의 장점을 가지고 있다. 또한 패턴 사파이어 기판위 GaN 에피 성장은 측면성장 효과를 통해 결함 밀도 감소와 광 추출 효율을 향상시키는 것으로 알려져 있다.또한 열응력으로 인한 기판의 휨 현상은 박막성장중 기판의 온도 분포를 불균일하게 만드는 원인이 되며 이는 결국 박막 조성 및 결정성의 열화를 유도하게 되고 최종적으로 소자특성을 떨어 뜨리는 원인이 되는데 AlN 중간층의 도입으로 이것을 완화시킬 수 있는 효과가 있다. 하지만, AlN 중간층이 패턴된 기판 위에 성장시킨 GaN 에피층에 미치는 영향은 명확하지 않다. 본 연구팀은 일반적인 c-plane 사파이어 기판과 플라즈마 건식 에칭을 통한 렌즈 모양의 패턴된 사파이어 기판을 이용해서 AlN 중간층과 GaN 에피층을 유기금속 화학기상증착법으로 성장하였다. 특히, 렌즈 모양의 패턴된 사파이어 기판은 패턴 모양과 패턴 밀도가 성장에 미치는 영향을 연구하기 위해 두가지 패턴의 사파이어 기판을 이용하였다. AlN 중간층 두께를 조절함으로써 최적화된 GaN 에피층을 90분까지 4단계로 시간 변화를 주어 성장 양상을 관찰한 결과, GaN 에피박막의 성장은 패턴 기판의 trench 부분에서 시작하여 기판의 패턴부분을 덮는 측면 성장을 보이고있다. 또한 TEM과 CL을 통해 GaN 에피박막의 관통 전위를 분석해 본 결과 측면 성장과정에서 성장 방향을 따라 옆으로 휘게 됨으로 표면까지 도달하는 결정결함의 수가 획기적으로 줄어드는 것을 확인함으로써 고품질의 GaN 에피층을 성장시킬 수 있었다. 그리고 패턴밀도가 높고 모양이 볼록할수록 측면 성장 효과로 인한 결정성 향상과 난반사 증가를 통한 임계각 증가로 광추출 효율이 향상 되는 것을 확인할 수 있었다. 이러한 결과를 바탕으로 최적화된 AlN 중간층을 이용하여 패턴 기판위에서 고품질의 GaN 에피층을 성장시킬 수 있었다.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.28 no.4
• /
• pp.339-345
• /
• 2008

The heat exchanger tube in nuclear power plants is mainly fabricated from nonferromagnetic material such as a copper, titanium, and inconel alloy, but the moisture separator & reheater tube in the turbine system is fabricated from ferromagnetic material such as a carbon steel or ferrite stainless steel which has a good mechanical properties in harsh environments of high pressure and temperature. Especially, the moisture separator & reheater tubes, which use steam as a heat transfer media, typically employ a tubing with integral fins to furnish higher heat transfer rates. The ferromagnetic tube typically shows superior properties in high pressure and temperature environments than a nonferromagnetic material, but can make a trouble during the normal operation of power plants because the ferrous tube has service-induced damage forms including a steam cutting, erosion, mechanical wear, stress corrosion cracking, etc. Therefore, nondestructive examination is periodically performed to evaluate the tube integrity. Now, the remote field testing(RFT) technique is one of the solution for examination of ferromagnetic tube because the conventional eddy current technique typically can not be applied to ferromagnetic tube such as a ferrite stainless steel due to the high electrical permeability of ferrous tube. In this study, we have designed RFT probes, calibration standards, artificial flaw specimen, and probe pusher-puller necessary for field application, and have successfully carry out RFT examination of the moisture separator & reheater tube of nuclear power plants.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.2
• /
• pp.7-13
• /
• 2019

This study aims to develop a FE Model to simulate dissimilar friction stir welding and to address its potential for fundamental analysis and practical applications. The FE model is based on Coupled Eulerian-Lagrangian approach. Multiphysics systems are calculated using explicit time integration algorithm, and heat generations by friction and inelastic heat conversion as well as heat transfer through the bottom surface are included. Using the developed model, friction stir welding between an Al6061T6 plate and an AZ61 plate were simulated. Three simulations are carried out varying the welding parameters. The model is capable of predicting the temperature and plastic strain fields and the distribution of void. The simulation results showed that temperature was generally greater in Mg plates and that, as a rotation speed increase, not the maximum temperature of Mg plate increased, but did the temperature of Al plate. In addition, the model could predict flash defects, however, the prediction of void near the welding tool was not satisfactory. Since the model includes the complex physics closely occurring during FSW, the model possibly analyze a lot of phenomena hard to discovered by experiments. However, practical applications may be limited due to huge simulation time.

• The Journal of Engineering Geology
• /
• v.29 no.1
• /
• pp.1-12
• /
• 2019

Earthquake can change underground stress condition around the hypocenter and affect the fracture systems of the rocks. In Korea, the M5.8 Gyeongju earthquake on September 12, 2016 and M5.4 Pohang earthquake on November 15, 2017 occurred inside the Yangsan fault zone and possibly affected the fracture systems in the Yangsan fault zone and nearby rock masses. In this study, the characteristics of the fracture system (fracture orientation, number of the fractures, fracture spacing and aperture, dip angle, fracture density along depth, and relative rock strength) of the rocks in the low/intermediate level radioactive waste repository site located in the coastal area of the East Sea are analyzed by the impact of the Gyeongju and Pohang earthquakes using acoustic televiewer data taken from the boreholes at the radioactive waste repository site in 2005 and 2018. As a result of acoustic televiewer logging analysis, the fracture numbers, fracture aperture, and fracture density along depth overall increased in 2018 comparing to those in 2005. This increase tendency may be due to changes in the fracture system due to the impact of the earthquakes, or due to weathering of the wall of the boreholes for a long period longer than 10 years after the installation of the boreholes in 2005. In the borehole KB-14, on the whole, the orientation of the fractures and the average fracture spacing are slightly different between 2005 and 2018, while dip angle and relative rock strength in 2005 and 2018 are similar each other.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.10 no.3
• /
• pp.276-284
• /
• 2022

In this study, performance evaluation and rheological characteristics were analyzed for recycling the fine powder of nuclear power plant dismantled waste concrete as a solidifying agent for radioactive waste disposal. The radioactive concrete fine powder was used to prepare a simulated sample, and the test specimen was prepared using Di-water, CoCl₂, and 1 mol CsCl aqueous solution as mixing water. Regardless of the aggregate mixing ratio and the type of mixing water, it satisfies the performance standard of 3.45 MPa for compressive strength at 28 days of age. All specimens satisfied the criteria for submersion strength, and the thermal cycle compressive strength satisfies the criteria for all specimens except Plain-50. As a result of evaluating the rheological properties of the solidifying agent, it was found that the increase in the aggregate mixing rate decreased the yield stress and plastic viscosity. The leaching index for cobalt and cesium of all specimens was 6 or higher, which satisfies the standard. In order to secure the stable performance of the solidifying agent, it is considered effective to use 40 % or less of the aggregate component in the solidifying agent.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.3A
• /
• pp.329-336
• /
• 2010

An experimental study to evaluate bursting behavior in anchorage zone of the standard PSC I girders (span length : 30 m) has been carried out. The arrangement of bursting reinforcement in anchorage zone of the standard PSC I girders is considered to be designed without accurately reflecting the stress flows in the end zone of the PSC I girders caused by presstressing forces of the tendons. Also, due to excessive arrangement of the bursting bars, the workability of the girder is decreased greatly. In this study, three specimens with the same dimensions as the end zone of the standard PSC I girder are prepared and the experiment is carried out by applying PS forces. The bursting reinforcement of each specimen consists of 100 mm, 200 mm, and 300mm spacings, respectively. The experimental results show that the range of the PS forces to cause crack in the anchorage zone of the specimen are more than 1.6 times of the design PS forces. The bursting cracks occur in the vertical direction on the inside of all specimens. After applying 2.7 times of the design PS force, some of the transverse bursting reinforcements only in the specimen reinforced by 300 mm spacing yielded. The experimental results show that the anchorage zone of the standard PSC I girders arranged by 300 mm spacing of the bursting reinforcements which is the maximum spacing allowed in the road bridge design specifications, can be considered safe enough.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.30 no.1
• /
• pp.63-72
• /
• 2024

Poly (butylene adipate-co-terephthalate) (PBAT) is one of the representative biodegradable polymers with high ductility and processability to replace petroleum-based polymers. Many investigations have been conducted to broaden the applications of PBAT in a variety of industries, including the food packaging, agricultural mulching film, and logistics and distribution fields. Foaming process is widely known technique to generate the cell structure within the polymer matrix, offering the insulation and light weight properties. However, there was no commercially feasible foam product based on biodegradable polymers, especially PBAT, and maintaining a proper melt viscosity of the polymer would be a key parameter for the foaming process. In this study, chemical foaming agent and cross-linking agent were introduced to PBAT, and a compression molding process was applied to prepare a foam sheet. The correlation between cell morphological structures and mechanical and physical properties was evaluated. It was found that PBAT with foam structures effectively reduced the density and thermal conductivity, allowing them to be suitable for applications such as insulation and lightweight packaging or cushion materials.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.34 no.3
• /
• pp.359-369
• /
• 2007

This in vitro study was performed to assess the effect of surface sealing on the microleakage of class V composite resin restorations that underwent several aging treatments. Class V cavities were prepared on the buccal surface of 100 sound extracted premolars and restored with a hybrid light-cured composite resin according to the manufacturer's instructions. They were randomly divided into two groups consisting of 50 samples: group I, without surface sealing, and group II, in which margins were etched and surface sealant was applied. After thermocycling, each group was divided into five subgroups, respectively, to represent the five aging treatments: group A = no further treatment (only thermocycling), B = toothbrushing, C = load cycling, D = toothbrushing followed by load cycling, and E = aging treatment in deionized water for six months. Microleakage was assessed by examining the penetration of 2% methylene blue dye. The following results were obtained: 1. At occlusal and cervical margins in groups without surface sealing, there was no significant difference in microleakage after the several aging treatments (p>0.05). 2. The occlusal margins of groups with surface sealing showed no significant differences after the several aging treatments (p>0.05). 3. In the cervical margins of groups with surface sealing, microleakage significantly increased after load cycling or aging in deionized water for six months (p<0.05). 4. The no-further-treatment group and the toothbrushing group with surface sealing showed less microleakage than the corresponding groups without surface sealing (p<0.05). 5. The surface-sealed groups with load cycling or aging in deionized water showed no significant difference in microleakage to the corresponding groups without surface sealing (p>0.05). In conclusion, the results of this study suggest that the surface sealant infiltrating through the gap of the cervical margin exerted a positive effect on microleakage at the initial stage, but the effect was not sufficient to overcome the stress generated by the cuspal flexure during occlusal loading and water absorption.