• Radiation Oncology Journal
• /
• v.14 no.1
• /
• pp.77-85
• /
• 1996

Purpose : Multileaf collimator(MLC) is very suitable tool for conformal radio-therapy and commissioning measurements for a multileaf collimator installed on a dual energy accelerator with 6 and 10MV photons are required, For modeling the collimator with treament planning software, detailed dosimetric characterization of the multileaf collimator including the penumbra width, leaf transmission between leaf leakage and localization of the leaf ends and sides is an essential requirement. materials and Methods : Measurement of characteristic data of the MLC with 26 pair block leaves installed on CLINAC 2100C linear accelerator was performed. Low sensitive radiographic film(X-omatV) was used for the penumbra measurement and separate experiments using radiographic film and thermoluminescent dosimeters were performed to verify the dose distribution, Measured films were analized with a photodensitometer of WP700i scanner. Results : For 6 & 10 MV x-ray energies, approximately $2.0\%$ of photons incident on the multileaf collimator were transmitted and an additional $0.5\%$ leakage occurs between the leaves. Localizing the physical end of the leaves showed less than 1mm deviation from the $50\%$ decrement line and this difference is attributed to the curved shaped end on the leaves One side of a sin히e leaf corresponded to the $50\%$ decrement line, but the opposite face was aligned with a lower value. This difference is due to the tongue and groove used to decrease between leaf leakage. Alignment of the leaves to form a straight edge resulted larger penumbra at far position from isocenter as compare with divergent alloy blocks. When the MLC edge is stepped by sloping field, the isodose lines follow the leaf pattern and Produce scalloping isodose curves in tissue. The effective penumbra by 45 degree stepped MLC is about 10mm at 10cm depth for 6MV x-ray. The difference of effective penumbra in deep tissue between MLC and divergent alloy blocks is small (5mm). Conclusion : Using the characteristic data of MLC, the MLC has the clinlical acceptability and suitability for 3-D conformal radiotherapy except small field size.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.14 no.4
• /
• pp.343-356
• /
• 2016

The Korea Radioactive Waste Agency (KORAD) has developed a dual-purpose metal cask for the dry storage of spent nuclear fuel that has been generated by domestic light-water reactors. The metal cask was designed in compliance with international and domestic technology standards, and safety was the most important consideration in developing the design. It was designed to maintain its integrity for 50 years in terms of major safety factors. The metal cask ensures the minimization of waste generated by maintenance activities during the storage period as well as the safe management of the waste. An activation evaluation of the main body, which includes internal and external components of metal casks whose design lifetime has expired, provides quantitative data on their radioactive inventory. The radioactive inventory of the main body and the components of the metal cask were calculated by applying the MCNP5 ORIGEN-2 evaluation system and by considering each component's chemical composition, neutron flux distribution, and reaction rate, as well as the duration of neutron irradiation during the storage period. The evaluation results revealed that 10 years after the end of the cask's design life, $^{60}Co$ had greater radioactivity than other nuclides among the metal materials. In the case of the neutron shield, nuclides that emit high-energy gamma rays such as $^{28}Al$ and $^{24}Na$ had greater radioactivity immediately after the design lifetime. However, their radioactivity level became negligible after six months due to their short half-life. The surface exposure dose rates of the canister and the main body of the metal cask from which the spent nuclear fuel had been removed with expiration of the design lifetime were determined to be at very low levels, and the radiation exposure doses to which radiation workers were subjected during the decommissioning process appeared to be at insignificant levels. The evaluations of this study strongly suggest that the nuclide inventory of a spent nuclear fuel metal cask can be utilized as basic data when decommissioning of a metal cask is planned, for example, for the development of a decommissioning plan, the determination of a decommissioning method, the estimation of radiation exposure to workers engaged in decommissioning operations, the management/reuse of radioactive wastes, etc.

• Applied Chemistry for Engineering
• /
• v.27 no.6
• /
• pp.583-589
• /
• 2016

Lubricant additives including zinc dialkyldithiophosphate (ZDDP) containing metal have been widely used due to the advantage of very low cost, but they can generate impurities such as ash. In this work, ZDDP containing metals was partially replaced with bis[3-(dialkyloxyphosphorothionyl) thio-2-methylpropanyloxy] butane (BAP4s) which was synthesized conveniently and effectively from alkanediol without any metal components. Also, the wear resistance property of synthesized BAP4s were studied. Wear scar diameter (WSD) values of BAP4s with butyl, octyl, decyl, dodecyl or tetradecyl groups were also measured by four-ball test. As the length of the alkyl group increased from 4 to 8, the WSD value of BAP4s decreased rapidly from 0.59 to 0.45 mm, but from 8 to 14, the value increased very slowly from 0.45 to 0.50 mm. Thus, among all BAP4s, B8P4 having BAP4 with the octyl group, showed the lowest WSD value. Furthermore, the WSD values were measured in a lubricant base oil mixed with a 0.50 percent concentration (w/w) of either BAP4 or ZDDP. The former was 0.55 mm, and the latter was 0.45 mm. The thermal stability and tribofilm formation peroperty were also measured by thermogravimetric analyzer (TGA) and energy-dispersive X-rays spectroscopy (EDS), respectively.

• Atmosphere
• /
• v.28 no.3
• /
• pp.305-315
• /
• 2018

This study investigates the characteristic spatial patterns and dynamic processes associated with the summertime extreme temperature events in South Korea during the last 20 years (1995~2014) using Self-Organizing Map (SOM). The classified SOM patterns commonly have high temperature and anticyclonic circulation anomalies over South Korea. The two major teleconnection patterns are identified: one is from the subtropical western North Pacific (WNP) affecting to the north and the other is from the North Atlantic (NA) affecting downstream region. The meridional teleconnection pattern is related to the forcing of positive sea surface temperature (SST) anomaly over the WNP. The northward propagating Rossby wave generates the East Asia-Pacific (EAP) pattern to form an anticyclonic circulation anomaly over South Korea. On the other hand, NA SST anomalies generate an eastward Rossby wave train across the Eurasian continent, leading to the development of an anticyclonic circulation anomaly over South Korea. The EAP pattern occurs more frequently in July and August, whereas the midlatitude teleconnection pattern associated with NA SST anomalies develops more frequently in early summer (June).

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.9 no.3
• /
• pp.203-212
• /
• 2005

Cellulose insulation is primarily manufactured from recycled newsprint and treated with fire retardants for the fire resistance. Thanks to the fire retardants, it is not combustible and flammable. In addition to that, Its thermal resistance is much better than that of fiberglass or rock wool. It is made from waste paper and easily decayed when it is demolished, and it has small embodied energy. So it is very environment-friendly building material. For broader use of cellulose insulation in buildings in Korea, it is necessary to test its physical performance to compare the results with the requirements on the Korean Building Code. To this end, apparent thermal conductivity (ka) measurements of Korean-made loose-fill cellulose insulations were recently completed using equipment that was built and operated in accordance with ASTM C 518 and the fire resistance was tested in accordance with ASTM C 1485. Korean loose-fill cellulose has thermal conductivity about 5% greater than the corresponding U.S. product at the same density. This is likely due to differences in the recycled material being used. Both spray-applied and loose-fill cellulose insulation lose about 1.5% of their thermal resistivity for $5.5^{\circ}C$ increase in temperature. The fire resistance of cellulose insulation is increased in linear proportion to the increase of the rate of fire retardant. Thanks to the high fire resistance, cellulose insulation can be used as a substitution of Styrofoam or Urethane foam which is combustible. The thermal conductivity of cellulose insulation was $0.037-0.043W/m{\cdot}K$ at the mean specimen temperature from $4-43^{\circ}C$. It corresponds to the thermal resistance of "Na Grade" according to the Korean Building Code. The effect of chemical content on thermal conductivity was negligible for all but the chemical-free specimen which had the highest value for the thermal conductivity over the temperature range tested. The thermal resistance of cellulose insulation is better than that of fiberglass or rock wool, and its fire resistance is higher than that of Styrofoam or Urethane foam. Therefore it can be substituted for those above considering its physical performance. Cellulose insulation is no more expensive than Styrofoam or rock wool, so it is recommended to use it more widely in Korea.

• Korean Journal of Food Science and Technology
• /
• v.30 no.3
• /
• pp.630-637
• /
• 1998

Enzymatic properties of immobilized transglucosidase (TG) from Aspergillus niger was characterized and compared with soluble TG. Michaelis-Menten constant $(K_m)$ and maximum velocity $(V_{max})$ of immobilized TG were $122\;mM,\;3.9{\times}10^{-2}\;mM/min$ and in case of soluble TG, 21 mM, 0.4 mM/min. The optimum pH of immobilized TG was pH 5.0 like soluble TG but immobilized TG showed 16% and 45% higher activity than soluble TG at pH 5.0 and pH 6.0. Both of immobilized TG and soluble TG were stable from pH 2.0 to pH 9.0, and therefore their activities in these pH ranges were remained more than 90%. The temperature was optimal at $60{\sim}70^{\circ}C\;and\;70{\sim}80^{\circ}C$ for soluble TG and immobilized TG, respectively. The thermal stability of immobilized TG was significantly improved than that of soluble TG, and immobilized TG retained $32{\sim}40%$ higher activity than soluble TG. D-values from thermal inactivation of immobilized TG were 7690 sec at $65^{\circ}C$, 83 sec at $75^{\circ}C$, 7.2 sec at $80^{\circ}C$. Z-values of soluble and immobilized TG were $6.4^{\circ}C\;and\;5.3^{\circ}C$, respectively. The little difference of activation energies of soluble TG and immobilized TG supposed that there was little difference in mass transfer limitation during the reaction of soluble TG and immobilized TG.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.32 no.2
• /
• pp.230-237
• /
• 2003

For hygenic evaluation, microbiological tests of seasoned raw vegetal)les from five high school foodservice operations were conducted. The antimicrobiological effect of pre-preparation with vinegar against microorganisms on vegetables in foodservice operations was also investigated. Total plate counts of leek gukgalli, broad bellflower saengchae and vegetable salad ranged from 10$^4$ CFU/g to 10$^{6}$ CFU/g. Coliform levels of those ranged from 10$^2$CFU/g to 10$^4$ CFU/g. Leek washed three times was pre-prepared at different concentration (0.05%,0.1%,0.5%,1% and 2%) and temperature ( 1$0^{\circ}C$ 2$0^{\circ}C$ and 4$0^{\circ}C$) for 5, 10 and 30 minutes. The higher the concentration and temperature of vinegar were, the more the antimicrobiological activity increased. The sanitizing activity of vinegar increased with treatment time. Considering the quality of vegetable and the expense, when the levels of total plate counts and coliform of vegetable were 10$^{6}$ and 10$^3$ CFU/g, pre-preparation with 0.5% of vinegar at 2$0^{\circ}C$ for 10 minutes was best. The population of total plate count and coliform on row and leek washed three times increased during storage for 72 hours. However, The levels of microorganism on leek samples pre-prepared with 0.5% and 1% vinegar decreased during storage. After the treatment of vinegar at 1$0^{\circ}C$ for 10 minutes, Staphylocucus aureus, Escherichia coli O157, Shigella sonnei, Salmonella entritidis, Listeria monolytogenes were not detected.

• Journal of Bio-Environment Control
• /
• v.24 no.2
• /
• pp.100-105
• /
• 2015

The calculation method of infiltration loss in greenhouse has different ideas in each design standard, so there is a big difference in each method according to the size of greenhouses, it is necessary to establish a more accurate method that can be applied to the domestic. In order to provide basic data for the formulation of the calculation method of greenhouse heating load, we measured the infiltration rates using the tracer gas method in plastic greenhouses equipped with various thermal curtains. And then the calculation methods of infiltration loss in greenhouses were reviewed. Infiltration rates of the multi-span and single-span greenhouses were measured in the range of $0.042{\sim}0.245h^{-1}$ and $0.056{\sim}0.336h^{-1}$ respectively, single-span greenhouses appeared to be slightly larger. Infiltration rate of the greenhouse has been shown to significantly decrease depending on the number of thermal curtain layers without separation of single-span and multi-span. As the temperature differences between indoor and outdoor increase, the infiltration rates tended to increase. In the range of low wind speed during the experiments, changes of infiltration rate according to the outdoor wind speed could not find a consistent trend. Infiltration rates for the greenhouse heating design need to present the values at the appropriate temperature difference between indoor and outdoor. The change in the infiltration rate according to the wind speed does not need to be considered because the maximum heating load is calculated at a low wind speed range. However the correction factors to increase slightly the maximum heating load including the overall heat transfer coefficient should be applied at the strong wind regions. After reviewing the calculation method of infiltration loss, a method of using the infiltration heat transfer coefficient and the greenhouse covering area was found to have a problem, a method of using the infiltration rate and the greenhouse volume was determined to be reasonable.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.10 no.6
• /
• pp.425-433
• /
• 2000

The stochiometric mix of evaporating materials for the $CuGaTe_2$single crystal thin films was prepared from horizontal furnance. Using extrapolation method of X-ray diffraction patterns for the $CuGaTe_2$polycrystal, it was found tetragonal structure whose lattice constant $a_0 and c_0$ were 6.025 $\AA$ and 11.931 $\AA$, respectively. To obtain the single crystal thin films, $CuGaTe_2$mixed crystal was deposited on throughly etched semi-insulator GaAs(100) substrate by the Hot Wall Epitaxy (HWE) system. The source and substrate temperature were $670^{\circ}C$ and $410^{\circ}C$ respectively, and the thickness of the single crystal thin films is 2.1$\mu\textrm{m}$. The crystalline structure of single crystal thin films was investigated by the photoluminescence and double crystal X-ray diffraction (DCXD). Hall effect on this sample was measured by the method of van der Pauw and studied on carrier density and mobility dependence on temperature. The carrier density and mobility of $CuGaTe_2$single crystal thin films deduced from Hall data are $8.72{\times}10{23}$개 $\textrm m^3$, $3.42{\times}10^{-2}$ $\textrm m^2$/V.s at 293K, respectively. From the photocurrent spectrum by illumination of perpendicular light on the c-axis of the $CuGaTe_2$single crystal thin film, we have found that the values of spin orbit coupling $\Delta$s.o and the crystal field splitting $\Delta$cr were 0.0791 eV and 0.2463 eV at 10 K, respectively. From the PL spectra at 10 K, the peaks corresponding to free bound excitons and D-A pair and a broad emission band due to SA is identified. The binding energy of the free excitons are determined to be 0.0470 eV and the dissipation energy of the donor-bound exciton and acceptor-bound exciton to be 0.0490 eV, 0.0558 eV, respectively.

• Journal of Sensor Science and Technology
• /
• v.6 no.4
• /
• pp.328-336
• /
• 1997

The CdSe thin films were grown on the Si(100) wafers by a hot wall epitaxy method (HWE). The source and substrate temperature are $600^{\circ}C$ and $430^{\circ}C$ respectively. The crystalline structure of epilayers was investigated by double crystal X-ray diffraction(DCXD). Hall effect on the sample was measured by the van der Pauw method and studied on the carrier density and mobility dependence on temperature. From Hall data, the mobility was increased in the temperature range 30K to 150K by impurity scattering and decreased in the temperature range 150k to 293k by the lattice scattering. In order to explore the applicability as a photoconductive cell, we measured the sensitivity(${\gamma}$), the ratio of photocurrent to darkcurrent(pc/dc), maximum allowable power dissipation(MAPD), spectral response and response time. The results indicated that the photoconductive characteristic were the best for the samples annealed in Cu vapor compare with in Cd, Se, air and vacuum vapour. Then we obtained the sensitivity of 0.99, the value of pc/dc of $1.39{\times}10^{7}$, the MAPD of 335mW, and the rise and decay time of 10ms and 9.5ms, respectively.