• Proceedings of the KIEE Conference
• /
• 2000.11c
• /
• pp.488-490
• /
• 2000

폴리에틸렌은 우수한 특성으로 절연재료분야에 광범위하게 사용되지만, 공간전하축적과 트리진전의 단점을 가지고 있으므로 이를 개선하기 위해 첨가제, 촉매법, 혼합법 등 다양한 방법들이 시도되어왔다. 메탈로센과 같은 촉매법과 첨가제법 등은 고분자의 전기적 특성은 개선되지만 가공성이 어려워지는 둥의 개선점들이 많이 존재한다. 하지만, 혼합법은 고분자 종류의 다양성과 시료 제작의 용이성으로 인하여 성질 개선법으로 자주 연구되고 있다. 혼합으로 인하여 재료의 특성에 따라 원 고분자의 고차구조가 변화되며 이는 원시료의 절연성능에 큰 영향을 미친다. 본 연구실에서는 선형저밀도 폴리에틸렌과 에틸렌비닐아세테이트를 중량비에 따라 혼합한 필름의 전기적 특성 고찰을 위하여 이미 전기 전도 특성과 유전특성에 대해 연구하여 혼합비 70 : 30인 시료와 혼합비 50 : 50인 시료의 전기적 특성이 우수함을 확인한 바가 있다. 따라서, 본 논문에서는 절연재료의 수명을 결정짓는 전원인가법에 따른 절연파괴 특성에 대해 물성분석을 통한 고차구조의 변화와의 상관성을 조사하였다.

• Journal of the Korean Chemical Society
• /
• v.46 no.2
• /
• pp.117-124
• /
• 2002

Counterflow oxidation was developed and evaluated for treatment of organics that adsorbed in/on granular activated carbon(GAC). This reaction is a method that destructs and removes organics adsorbed, at the same time, regenerates waste carbon, uti lizing a self-sustained flame which propagates itself ina direction counter to the oxygen flow. The results showed that the mass loss of carbon and flam temperature were strongly dependent on the flow rate of oxyen, adsorptive capability of regenerated carbon completely was recovered, as well as destrution and removal efficiency of thermally stable PCBs was achieved with the value of better than 99.99%.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.72-77
• /
• 2004

In a primary reactor cooling system(RCS), a dissimilar weld zone exists between cast stainless steel(CF8M) in a pipe and low-alloy steel(SA508 cl.3) in a nozzle. Thermal aging is observed in CF8M as the RCS is exposed for a long period of time to a reactor operating temperature between 290 and $330^{\circ}C$, while no effect is observed in SA508 cl.3. The specimens are prepared by an artificially accelerated aging technique maintained for 300, 1800 and 3600 hrs at $430^{\circ}C$, respectively. The specimens for elastic-plastic fracture toughness tests are prepared one type, which notch is created in the heat affected zone(HAZ) of CF8M. And, the specimens for fatigue crack growth tests are prepared in three classes, which notches are created at the center of deposited zone, the HAZ of CF8M, and the HAZ of SA508 cl.3. From the experiments, the J-integral values with the increase of aging time decrease, and the differences of the fatigue crack growth behaviors are relatively small in the three classes specimens.

• The Magazine of the Society of Air-Conditioning and Refrigerating Engineers of Korea
• /
• v.31 no.7
• /
• pp.65-70
• /
• 2002

지구의 오존층을 보호하기 위한 몬트리올 의정서가 1987년 채택된 이후 오존층 파괴물질의 사용이 점차 감소되고 있다. 선진국의 경우 1995년 말부터 CFC냉매의 생산을 전폐하였고, HCFC냉매의 경우는 2020년 전폐를 목표로 대체냉매를 이용한 응용 기술개발 및 제품 생산이 진행되고 있다. 가정용 냉장고 및 차량용 에어컨에는 R-12의 대체냉매로 R-134a가 도입되었으며, 유럽을 중심으로 냉장고에는 HC계 냉매인 R-600a도 대체냉매로 사용되고 있다. 가정용 에어컨에는 혼합냉매인 R-407c 와 R-410a가 R-22 냉매를 대체하여 적용되고 있다. 그러나 현재, CFC및 HCFC 대체 냉매로 많이 사용되고 있는 HFC계 냉매도 지구 온난화 지수가 대단히 큰 문제를 가지고 있다. 1997년 채택된 교토의 정서에는 HFC계 냉매가 온실효과가 가스 배출규제물질에 포함되어 있다. 이에 따라서 오존층의 파괴지수가 영이고 지구온난화지수도 거의 없는 자연냉매가 주목을 받게 되었으며, 자연 냉매의 하나인 이산화탄소 ($CO_2$R744) 냉매의 응용기술 및 제품개발 연구가 선진국을 중심으로 폭넓게 진행되고 잇다. 본고에서는 $CO_2$냉매의 일반적인 특성을 간단히 소개하고 일본에서 진행되고 있는 $CO_2$냉매를 적용한 급탕시스템의 제품개발 및 시장현황에 대해서 기술하기로 한다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05c
• /
• pp.219-222
• /
• 2003

$0.2(PbMg_{1/3}Nb_{2/3}O_3)-0.8(PbZr_{0.475}Ti_{0.525}O_3)$ 조성을 이용하여 $5{\times}5{\times}5mm^3$의 적층형 세라믹 액츄에이터 소자를 tape casting 방법으로 제작하였다. 전극재로서는 Ag-Pd를 이용하여 총 50층의 layer를 적층하였으며, 적층된 액츄에이터를 $1100^{\circ}C$의 온도에서 소결하였다. X-ray diffractometer를 이용하여 제작된 소자와 열화된 소자의 구조적인 특성을 분석하였다. 제작된 소자의 열화 특성을 알아보기 위하여 60 Hz 의 triangular wave를 인가하여 열화전과 후의 p-E hystcresis loop의 변화를 살펴보았으며, 인가된 전압의 변화에 따라서 소자에서 발생되는 양의 열을 측정하였다. 파괴된 소자의 파단면에 대한 SEM 분석을 통하여 소자의 파괴 메카니즘을 알아보도록 하였다. 이로부터 전기적 기계적 열화가 소자의 동작에 미치는 영향에 대해서 알아 보았다.

• Journal of Welding and Joining
• /
• v.7 no.4
• /
• pp.56-67
• /
• 1989

In this study, the possibility of evaluating the peculiar fracture strength of weldment in high strength steels was investigated by means of a small punch(SP) test. In order to obtain the ductile-brittle transition temperature(DBTT) of SP energy by which the fracture strength of weldment in structural steels such as SS41 and SM53B steels had been evaluated in our preceding publication, the effects of notches and loading rates on SP energy were discussed. It was found that the correspondence of SP energy to critical COD at test temperature -196.deg. C showed a linear relation with some deviation. The empirical correlation with scatter band, Esp/(Esp)p = 1.67[.delta./(.delta./sub c//(.delta./sub c/)/sub p/]-0.55, was developed between the SP energy ratio and critical COD ratio of each weld structure compared with parent material at test temperature -196.deg. C. In addition, there did not appear to be a significant effect of test materials and specimen size etc. on the correlation.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.11
• /
• pp.1207-1214
• /
• 2014

Under excessive plasticity, the fracture toughness of a material depends on its size and geometry. Under fully yielded conditions, the stresses in a material near its crack tip are not unique but rather depend on the geometry. Therefore, the single-parameter J-approach is limited to a high-constraint crack geometry. The JQ theory has been proposed for establishing the crack geometry constraints. This approach assumes that the crack-tip fields have two degrees of freedom. In this study, the crack-tip stress field of a fully circumferential surface-cracked pipe under combined loads is investigated on the basis of the JQ theory by using finite element analysis. The combined loads are a tensile axial force and the thermal gradient in the radial direction. Q-stresses of the crack geometry and its loading state are used to determine the constraint effects. The constraint effects of secondary loading are found to be greater than those of primary loading. Therefore, thermal shock is believed to be the most severe loading condition of constraint effects.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.9 no.1
• /
• pp.40-46
• /
• 1985

Some problems such as toughness decrement and stess relief cracking (SRC), many occur when post weld heat treatment (PWHT) is applied to remove residual stress adn hydrogen. In this paper PWHT was carried out under the stress of 0, 98, 196 and 294 MPa (0, 10, 20 and 30kgf/mm$^{2}$ each) to simulate residual stress in HAZ of Cr-Mo steel. The effect of applied stress during PWHT on fracture toughness was evaluated by COD fracture toughness test, micro-hardnes test and observation of SEM. The experimental results are as follows; (1) Fracture toughness of weld HAZ was improved by PWHT, but it decreased as heat treated under the stress. (2)Hardness ratio under the stress of 294MPa (30kg/mm$^{2}$) was lower and fracture toughness was decreased than that of the no stress. (3) Applied stress in weld HAZ during PWHT assisted precipitation of over saturated alloying elements in the structure, so fracture surface at the stress of 294MPa (30kg/mm$_{2}$) appeared the grain boundary failure possibly one of the reasons for PWHT embrittlenment.

• Journal of Sensor Science and Technology
• /
• v.8 no.6
• /
• pp.440-447
• /
• 1999

Tensile stress loaded on smart composite structures and thermal stress occurred during the during process of the smart composite materials with embedded optical fiber sensors affect directly the mechanical behavior of the embedded optical fiber sensors within the smart composite structures. Stress distribution within the optical fiber sensors varies with respect to the stacking sequence of the composite laminate and the coating conditions of the optical fibers. The cracks occurred within the composite laminate affect not only the fracture of the composite laminate but also the fracture of the optical fiber sensors embedded within the composite laminate. In this study, firstly, stress distribution of the optical fiber sensors embedded within the composite laminate which is subjected to the tensile and thermal stresses was analyzed using Finite Element Method. And, secondly, the effect of the stacking sequence of the composite laminate and the coating conditions of the optical fiber sensors on the stress distribution of the optical fiber sensors was investigated. Finally, the effect of the crack occurred within the smart composite laminate on the fracture behavior of the optical fiber sensors was also observed through the tensile test.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.3
• /
• pp.624-635
• /
• 1990

Analytical study based on linear fracture mechanics was conducted on propagation behavior of inclined surface crack in semi-infinite elastic body. The analytical model was assumed to be inclined surface crack under plane strain condition upon which Hertzian stress was superimposed. Supposing continuous distribution of dislocation and applying Erdogan-Gupta's method to this crack problem, the stress intensity factors $K_{I}$ and $K_{II}$) at the crack-tip were obtained for various Hertzian contact positions. Analytic results have shown that driving force for crack growth is $K_{I}$ for non-lubricated condition and $K_{II}$ for fluid and boundary lubricated condition. The coefficient of friction at the hertzian contact and crack surfaces plays an important role in predicting the direction of crack propagation. It is also found that the maximum effective stress intensity factor exists at cracks of a certain specific length depending on lubricated condition.ion.n.