• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1999.12a
• /
• pp.523-530
• /
• 1999

연속살균장치는 $130^{\circ}C$에서 $140^{\circ}C$의 초고온에서 연속적으로 식품을 열처리 하는 공정으로 재래 배치식 공정에 비하여 순간적인 짧은 시간이 소요되는 경제적인 공정이나, 액상과 고상으로 구성된 저산도 식품은 고상입자의 대류열전달 계수와 장치내 체류시간이 정확히 구명되지 않아서 연속살균기술이 성공적으로 적용되지 못하고 있다. 본 연구에서 연속살균장치에서의 액상식품과 고상식품사이의 대류열전달 계수를 예측하기 위하여 연속살균장치의 Hold tube에서 정육면체 모델 식품내부의 온도를 측정할 수 있는 장치를 개발하였다. 연속살균장치의 홀드튜브에서 정육면체 모델 식품의 온도변화를 예측할 수 있는 유한차분법을 이용한 시뮬레이션 모델을 개발하고 소고기를 대상으로 이 시뮬레이션 모델의 입력변수인 비열, 열전도도를 실험적으로 측정하여 사용하였다. 0.0에서 15.0 centipoise의 점도를 가지는 모델 액상식품의 15.6에서 45.2liter/min 의 유속에 대하여 액상과 소고기 정육면체의 대류열전달계수는 792에서 2107W/$m^2$K으로 예측되었다.

• Clean Technology
• /
• v.16 no.2
• /
• pp.140-144
• /
• 2010

Titania-silica composite materials were obtained by sol-gel method from TiCl4 and TEOS precusors, and they were applied to anode materials of lithium ion battery. Uniformly distributed composite materials can be manufactured by sol-gel method. The composite materials were heat treated by microwave to obtain materials with new properties. The experimental variables were composition of the material, heat treatment temperature, and microwave exposure. The structure and surface properties of the materials were analyzed by XRD, SEM, and the electrochemical capacity was measured with charge/discharge cycler.

• Polymer(Korea)
• /
• v.34 no.3
• /
• pp.210-214
• /
• 2010

The structural development of triacetyl cellulose (TAC) was studied as a function of solution casting processing parameters such as dope concentration, evaporation temperature, annealing temperature and the addition of plasticizer. The crystalline structure was developed by the solution casting and the level of crystallinity was increased with increasing dope concentration and evaporation temperature. The crystalline structure could be enhanced by the annealing process after formation of TAC film. Introducing plasticizer resulted in decreasing melting temperature and crytallinity of TAC film due to the increase of chain mobility. It was also found that thermal stability of TAC was improved due to the rigid structure of applied plasticizer.

• Korean Journal of Materials Research
• /
• v.9 no.11
• /
• pp.1095-1101
• /
• 1999

Electroless Ni plating is applied to form bumps and UBM layer for flip chip interconnection. Characteristics of electroless Ni are also investigated. Zincate pretreatment is analyzed and plated layer characteristics are investigated according to variables like temperature, pH and heat treatment. Based on these observations, characteristics dependence to each variables and optimum electroless Ni plating conditions for flip-chip interconnection are suggested. Electroless Ni has 10wt% P, $60\mu\Omega$-cm resistivity, 500HV hardness and amorphous structure. It changes crystallized structure and hardness increases after heat treatment After interconnection of electroless Ni bumps by ACF flip chip method, we show their advantages and possibility in microelectronic package applications.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.105-105
• /
• 2018

스테인리스강은 내식성과 내구성이 우수하여 파이프 및 일반 구조용 고온재료에 널리 사용된다. 그러나 선박 및 해양플랜트 등의 고부가가치 산업에 사용될 경우 내피로성, 내구성 및 내식성이 더욱 요구되고 있다. 특히 해수 환경 하에서 스테인리스강은 재료 표면의 부동태 피막 파괴로 공식 또는 틈부식에 의한 국부부식을 초래하여 해양환경용 재료로 사용하는데 제한적이다. 플라즈마 이온질화는 저온에서 열처리가 가능하며 재료의 변형이 없어 스테인리스강에 널리 적용되는 열화학적 표면처리 기술이다. 플라즈마 이온질화는 일반적으로 고온에서 실시하여 스테인리스강의 기계적 특성을 향상시키는 목적으로 주로 적용하였으나, 저온-플라즈마 이온질화 처리 시 질소의 확산계수 증가로 표면에 S-phase 생성에 기인하여 부식 저항성이 향상된다고 알려져 있다[1-2]. 그러나 해수 펌프, 밸브, 스트레이너(Strainer) 등의 해양 환경용 기자재로 널리 사용되고 있는 주조 스테인리스강에 대한 플라즈마 이온질화 적용과 그 연구는 미비하다. 따라서 본 연구에서는 주조용 스테인리스강에 대하여 플라즈마 이온질화 기술을 적용하여 공정온도에 따른 해수 내 전기화학적 부식 특성을 규명하였다. 플라즈마 이온질화 공정은 $25%N_2$와 $75%H_2$ 비율로 $350^{\circ}C{\sim}500^{\circ}C$의 공정온도에서 10시간 동안 실시하였다. X-선 회절분석을 통해 공정온도 변수에 따른 표면에 형성된 질화층의 상변화를 분석하였다. 또한 비커스 경도계를 이용하여 표면경도를 측정하여 기계적 특성 향상을 확인하였다. 전기화학적 부식 실험 후 표면 손상 형상 관찰, 무게 감소량 및 손상 깊이 계측을 통해 공정 온도와 부식 저항 특성을 규명하였다. 또한 타펠 분석을 통해 모재와 플라즈마 이온질화 온도 변수에 따른 부식 속도를 비교 분석하였다.

• Journal of the Korean Ceramic Society
• /
• v.40 no.10
• /
• pp.949-953
• /
• 2003

Blue emitting CaWO$_4$ thin films were deposited by rf magnetron sputtering. The effect of sputtering parameters and annealing conditions on the luminescent properties were investigated. Structural and stoichiometric properties of thin films were affected by $O_2$/Ar gas ratio and substrate temperature. Post-annealing caused the phosphor thin films to emit improved luminescent properties. The atomic composition of films might depend on annealing atmosphere, which resulted in the changes of luminescent properties. Blue-green emission that was due to oxygen vacancies was observed. However, by controlling oxygen defects, only blue emission could be obtained.

• Korean Journal of Materials Research
• /
• v.8 no.8
• /
• pp.707-713
• /
• 1998

The influence of plasma carburizing process on the surface hardness of SCM415 low-alloy steel (0.15% C) was investigated under the various process conditions of gas composition. gas pressure, plasma current density. temperature and time. The effective case depth was found to depend on the amount of methan gas containing carbon. thus the deepest case depth and the uniform hardeness were obtained with the 100% methan gas. The case depth increased with the plasma current density. The effective plasma carburizing temperature of SCM415 steel was found to be higher than 85$0^{\circ}C$, and the case depth was proportional to the square root of carburizing time under the same current density. The bending fatigue strength of the plasma carburized specimen is' higher than those of as- received specimen or reheat-quenched specimen.

• Korean Journal of Materials Research
• /
• v.8 no.11
• /
• pp.987-992
• /
• 1998

Titanium aluminide intermetallic compound was formed from high purity elemental Ti and A1 foils by selfpropagating, high-temperature synthesis(SHS1 in hot press. Formation of $TiAl_3$ intermetallics at the interface between Ti and Al foil was observed to be controlled by temperature, pressure and heating rate. Especially, the heating rate is the most important role to form intermetallic compound by SHS reaction. According to DTA experiment, the SHS reactions appeared at two different temperatures below and above the melting point of Al. It was also observed that both SHS reaction temperatures increased with increasing the heating rate. After the SHS reaction of alternatively layered 10 Ti and 9 A1 foils at the heating rate of $20^{\circ}C$/min, the $700\mu\textrm{m}$ thick titanium aluminide sheet was formed by heat treatment at $810^{\circ}C$ for 4hours.

• Korean Journal of Materials Research
• /
• v.9 no.7
• /
• pp.740-747
• /
• 1999

Grain refinement is the only strengthening mechanism that improves both strength and toughness. Controlled rolling and accelerated cooling techniques have been known to be effective method to improve the mechanical properties by controlling the recrystallization and/or grain coarsening during processing. Repeat phase transformation $(\gamma/\alpha)$ by repeat heat treating is another way of grain refinement. In this study, a combined effect of controlled rolling and repeat heat treating was investigated. To study the effects of Mo addition and process parameters, Mo alloyed low carbon steels were prepared and thermomechanical controlled processes were simulated in the Gleeble system. The Mo addition resulted in an increasement of the grain coarsening temperature and suppress austenite recrystallization. The optimum condition for the refinement of austenite was obtained when the controlled rolling was performed twice with the same heat treatment condition, and reduction ratio of second pass was higher than that of first pass.

• Journal of the Korean Vacuum Society
• /
• v.6 no.3
• /
• pp.249-254
• /
• 1997

We investigated characteristics of Fe-doped semi-insulating InP by means of photoreflectance(PR) measurement. The band gap energy($E_0$) and broadening parameter($\Gamma$) from PR signals at 300K are 1.336 eV and 11.2 meV, respectively. As the temperature is decreased from 300 to 80 K, PR signals are varied from an overlapped shape of exciton and 2-dimensional band gap transitions(300 K) to that of exciton transition(80 K). We calculated Varshni coefficient($\alpha=0.94\pm$0.07 meV/K, $\beta=587\pm$35.2 K) and Bose-Einstein coefficient ($a_B=33.6{\pm}2.02meV$ , $\theta=165\pm$33K). After annealing of isothermal and isochronism crystallinity of InP is found to be excellent when annealed at $300^{\circ}C$ for 10~20 min, qualitatively.