• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.22 no.2
• /
• pp.92-98
• /
• 2012

The co-precipitation technique has been applied to synthesize biphasic calcium phosphate (BCP). $Ca(NO_3)_2{\cdot}4H_2O$, $(NH_4)_2HPO_4$, TEOS and $Mg(NO_3)_2{\cdot}6H_2O$ as the starting materials was used. After the heat treatment of powder crystalline phases HAp and ${\beta}$-TCP analysis showed a mixed phase. The overall spectra appear to have mainly two modes corresponding to characteristic $PO^{3-}_4$ and $OH^-$ groups. After immersion in Hanks' Balanced Salt Solution (HBSS) for 1 week a precipitation started to be formed with individual small granules on the specimen surface. An MTT assay indicated that ionic substituted BCP powders had no cytotoxic effects on MG-63 cells, and that they have good biocompatibility.

• Korean Chemical Engineering Research
• /
• v.49 no.6
• /
• pp.786-789
• /
• 2011

In order to estimate the possibility of applying electrolytes generally used in solid oxide fuel cells(SOFCs) to direct carbon fuel cells(DCFCs), properties of YSZ(yttria stabilized zirconia) electrolyte were evaluated. In this study, vacuum slurry coating method was adapted to coat thin layer on anode support substrate. After sintering the electrolyte at $1400^{\circ}C$ for 5hrs, microstructure was analyzed by using SEM image. Also, gas permeability and ionic conductivity were measured to find out the potential possibility of electrolyte for DCFCs. The YSZ electrolyte represented dense coating layer and low gas permeability value. The ionic conductivity of YSZ electrolyte was high over $800^{\circ}C$. After measurement of the electrolyte properties, direct carbon fuel cell was fabricated and its performance was measured at $800^{\circ}C$.

• KSBB Journal
• /
• v.24 no.2
• /
• pp.163-169
• /
• 2009

Lovastatin (also known as Mevinolin, Mevacor, and Monacolin K), an inhibitor of the HMG-CoA reductase produced by Aspergillus terreus and other fungi, is used to reduce serum cholesterol levels in human beings. It is derived biosynthetically from two polyketides. One of these is a nonaketide that undergoes cyclization at a hexahydronaphthalene ring system, and the other is a simple diketide, 2-methylbutyrate. Two primer pairs were designed based on the amino acid sequences of lovastatin polyketide synthase and lovastatin diketide synthase for the PCR screening of lovastatin-producing strains. Among the seven selected strains, SJ-2 evidenced the highest level of lovastatin production in both liquid and solid cultures. Soybeans with SJ-2 were treated via 1 hour of heat shock at $30^{\circ}C$ for the mass production of lovastatin. The heat-treated soybeans were inoculated on rice bran and the koji extract was obtained after 15 days of incubation. It yielded the highest level of lovastatin production among the strains, and also evidenced 75% inhibition activity against HMG-CoA reductase. We developed an efficient PCR screening method for lovastatin-producing strains, using lovastatin biosynthesis genes.

• Korean Chemical Engineering Research
• /
• v.45 no.4
• /
• pp.328-334
• /
• 2007

Chemical heat pump system of 2-propanol/acetone/hydrogen is most suitable to the recovery of waste heat of power plant. various types of 5 wt% Pt-alumina catalysts were prepared for 2-propanol dehydrogenation using sol-gel method. The characteristics and the dehydrogenation reaction rate of each catalyst were investigated. Pt-alumina xerogel catalyst has excellent reaction rate and good durability in comparison with the existing alumina supported Pt catalysts. Pt-alumina aerogel catalyst had the highest reaction rate in all prepared catalysts, but sufficient aging time was necessary to maintain its reaction rate. A potential advantage of the aerogel catalyst is the fact that the high temperature heat treatment is not required. Without heat treatment or with low temperature heat treatment, the Pt-alumina aerogel catalyst has excellent reaction rate as well as durability and this gives us the economic advantage. Alumina xerogel supported Pt catalyst prepared by incipient wetness method showed good reaction rate, and had good mechanical strength. Blank alumina xerogel prepared by sol-gel method can be used for the support of metal catalysts.

• Journal of Life Science
• /
• v.27 no.9
• /
• pp.1003-1010
• /
• 2017

An open reading frame coding for mannanase predicted from the partial genomic sequence of Paenibacillus woosongensis was cloned into Escherichia coli by polymerase chain reaction amplification, and completely sequenced. This mannanase gene, designated man26AT, consisted of 3,162 nucleotides encoding a polypeptide of 1,053 amino acid residues. Based on the deduced amino acid sequence, Man26AT was identified as a modular enzyme, which included a catalytic domain belonging to the glycosyl hydrolase family 26 and two carbohydrate-binding modules, CBM27 and CBM11. The amino acid sequence of Man26AT was homologous to that of several putative mannanases, with identity of 81% for P. ihumii and identity of less than 57% for other strains of Paenibacillus. A cell-free extract of recombinant E. coli carrying the man26AT gene showed maximal mannanase activity at $55^{\circ}C$ and pH 5.5. The enzyme retained above 80% of maximal activity after preincubation for 1 h at $50^{\circ}C$. Man26AT was comparably active on locust bean gum (LBG), galactomanan, and kojac glucomannan, whereas it did not exhibit activity on carboxymethylcellulose, xylan, or para-nitrophenyl-${\beta}$-mannopyranoside. The common end products liberated from mannooligosaccharides, including mannotriose, mannotetraose, mannopentaose, and mannohexaose, or LBG by Man26AT were mannose, mannobiose, and mannotriose. Mannooligosacchrides larger than mannotriose were found in enzymatic hydrolyzates of LBG and guar gum, respectively. However, Man26AT was unable to hydrolyze mannobiose. Man26AT was intracellularly degraded into at least three active proteins with different molecular masses by zymogram.

• Korean Journal of Materials Research
• /
• v.8 no.10
• /
• pp.890-897
• /
• 1998

The direct wafer bonding between n-InP(001) wafer and the ${Si}_3N_4$(200 nm) film grown on the InP wafer by PECVD method was investigated. The surface states of InP wafer and ${Si}_3N_4$/InP which strongly depend upon the direct wafer bonding strength between them when they are brought into contact, were characterized by the contact angle measurement technique and atomic force microscopy. When InP wafer was etched by $50{\%}$ HF, contact angle was $5^{\circ}$ and RMS roughness was $1.54{\AA}$. When ${Si}_3N_4$ was etched by ammonia solution, RMS roughness was $3.11{\AA}$. The considerable amount of initial bonding strength between InP wafer and ${Si}_3N_4$/InP was observed when the two wafer was contacted after the etching process by $50{\%}$ HF and ammonia solution respectively. The bonded specimen was heat treated in $H^2$ or $N^2$, ambient at the temperature of $580^{\circ}C$-$680^{\circ}C$ for lhr. The bonding state was confirmed by SAT(Scannig Acoustic Tomography). The bonding strength was measured by shear force measurement of ${Si}_3N_4$/InP to InP wafer increased up to the same level of PECVD interface. The direct wafer bonding interface and ${Si}_3N_4$/InP PECVD interface were chracterized by TEM and AES.

• Journal of the Korean Electrochemical Society
• /
• v.14 no.1
• /
• pp.27-32
• /
• 2011

The electorchemical properties of $Li_4Ti_5O_{12}$ added with Cr was tested. The addition or substitution of atoms to $Li_4Ti_5O_{12}$ are expected to modify the crystal structure, and therefore to change the electrochemical performances of $Li_4Ti_5O_{12}$. After the spinel structure $Li_4Ti_{5-x}Cr_xO_{12}$ (x = 0~0.2) were obtained via sol-gel method, the gel was heated in a muffle furnace at $800{\sim}850^{\circ}C$ for 12 h in air. The physical properties of the samples were characterized by TG-DTA, XRD, SEM, FT-IR, and the electrochemical properties were tested with battery cycler at 0.01~2.0 V range. The $Li_4Ti_5O_{12}$ exhibited 169.9 mAh/g at 1C and capacity recovery was 97.5% of the initial capacity at 0.1C. $Li_4Ti_{4.9}Cr_{0.1}O_{12}$ (Cr 1% added) showed best performance of 193.8 mAh/g at 1C and the capacity recovery was increased to 98.8% of the initial capacity at 0.1C.

• Journal of the Korean Electrochemical Society
• /
• v.16 no.3
• /
• pp.184-189
• /
• 2013

$Ba_2SiO_4:Eu^{2+}$ ($B_2S:Eu^{2+}$) powders were prepared by firing the dry gel obtained by the sol-gel and the hybrid process (sol-gel and combustion), respectively, and their structure and luminescence were investigated. Tetraethyl orthosilicate (TEOS) was used as a Si source. The phase transition was observed with the TEOS content. With 1.2M TEOS, the powders prepared by the sol-gel process without prior calcination were composed of the $B_2S:Eu^{2+}$ single phase, whereas those by the sol-gel and the hybrid process with prior calcination consisted of the dominant $B_2S:Eu^{2+}$ and minor $BaSiO_3:Eu^{2+}$ ($BS:Eu^{2+}$) phases and their emission intensities were approximately two times higher than those without prior calcination. The hybrid process could reduce the process time innovatively compared to the sol-gel process, even though the former was a little inferior to the latter in the emission intensity of $B_2S:Eu^{2+}$. With 1.1M TEOS, the $B_2S:Eu^{2+}$ single phase was obtained by the hybrid process, and its green emission was observed at 505 nm originated from the $4f^65d^1{\rightarrow}4f^7$ transition of $Eu^{2+}$ ions.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.39 no.10
• /
• pp.1503-1508
• /
• 2010

This study was conducted to investigate physicochemical characteristics, antioxidant activities, and sensory evaluation of water extracts from Liriopis tuber (Liriope platyphylla Wang et Tang; LP) treated with roasting over various temperatures ($150{\sim}190^{\circ}C$). The LP water extracts showed increase of total sugar, reducing sugar, total protein, and total saponins except pH as roasting temperature was elevated. The browning index, and a and b values of color were increased, however, L value was decreased as temperature was elevated. 1,1-diphenyl-2-picrylhydrazyl (DPPH) radical, superoxide anion radical, and nitrite scavenging activities and trolox equivalent antioxidant capacity of LP water extracts were increased by 6.77, 2.37, 4.02, and 4.92 times, respectively, after roasting at $190^{\circ}C$. In sensory evaluation, LP water extracts roasted at $170^{\circ}C$ showed the highest scores in color, savory taste, flavor, and overall acceptability.

• Journal of Sensor Science and Technology
• /
• v.5 no.5
• /
• pp.21-29
• /
• 1996

A piezoresistive silicon acceleration sensor with 8 beams, utilized by an unique silicon micromachining technique using porous silicon etching method which was fabricated on the selectively diffused (111)-oriented $n/n^{+}/n$ silicon subtrates. The width, length, and thickness of the beam was $100\;{\mu}m$, $500\;{\mu}m$, and $7\;{\mu}m$, respectively, and the diameter of the mass paddle (the region suspended by the eight beams) was 1.4 mm. The seismic mass on the mass paddle was formed about 2 mg so as to measure accelerations of the range of 50g for automotive applications. For the formation of the mass, the solder mass was loaded on the mass paddle by dispensing Pb/Sn/Ag solder paste. After the solder paste is deposited, Heat treatment was carried out on the 3-zone reflow equipment. The decay time of the output signal to impulse excitation of the fabricated sensor was observed for approximately 30 ms. The sensitivity measured through summing circuit was 2.9 mV/g and the nonlinearity of the sensor was less than 2% of the full scale output. The output deviation of each bridge was ${\pm}4%$. The cross-axis sensitivity was within 4% and the resonant frequency was found to be 2.15 KHz from the FEM simulation results.