• Applied Chemistry for Engineering
• /
• v.20 no.5
• /
• pp.511-516
• /
• 2009

Photodegradation characteristics of polyolefin composites were studied. Thermogravimetric analysis results suggest that the polyolefin blends used in this study have different amounts of talc. The mechanical behaviors of polyolefin blends, which experienced UV-irradiation in accordance with SAE J1960, are investigated using tensile and Izod impact tests. These results show that as the UV-exposure time increases, a significant drop in the elongation at break and impact strength at a low temperature are observed. This may be explained by the decreases in elastic energy derived from the scission of polymer molecular chains and the low density of entanglement after UV- photodegradation. Scanning electron microscopy observations indicate that no crack and surface damage are observed, while the additional talc particles are exposed, on the UV-exposed surfaces. The exposure of talc particles may be responsible for the discoloration of UV-exposed polyolefin blend surface. Observation using Fourier transform infrared spectroscopy (FT-IR) confirms the presence of photodegradation on the surface of UV-exposed polyolefin blend.

• Journal of Biomedical Engineering Research
• /
• v.24 no.5
• /
• pp.375-380
• /
• 2003

In this study. we have intended to control the properties of surface reaction zone generated between pure titanium and oxide investment moulds. Commercially pure titanium was centrifugally casted and silica$.$alumina based phosphate bonded investment was used as the mould material. The effect of cooling methods after casting on the surface reaction zone and mechanical properties of casts were investigated. The resulting casts showed the multilayered surface reaction zone regardless of cooling method. Especially. water cooling method produced the titanium casts with thinner surface reaction zone. weaker strength. and higher elongation properties compared to air cooling. It can thus be known that the resulting casts had satisfactory mechanical properties as dental materials. From these results, the cooling rate dependence of interfacial and mechanical properties can be attributed to the diffusion of oxygen from casting environment, which control the reaction of titanium and mould.

• Composites Research
• /
• v.12 no.2
• /
• pp.91-100
• /
• 1999

The manufacture of high strength polyethylene(HSPE) tape yarns has been accomplished by a solid state processing(SSP) method as the compaction of ultra-high molecular weight polyethylene(UHMWPE) powders and drawing of the compacted film under the melting point without any organic solvents. In this study, the characteristics of HSPE tape yarns produced by SSP which is desirable for production cost and environmental aspect were analyzed. As the results, tensile strengths of HSPE tape yarns increased with increasing the draw ratio and the fracture morphology of highly drawn HSPE tape yarns showed more fibrillar shape than the low drawn one. Interfacial shear strengths of HSPE tape yarns with vinylester resin increased by $O_2$ plasma treatment and maximum interfacial shear strength was obtained in the plasma treatment condition of 100W and 5min. In addition, mechanical properties of HSPE tape yarn reinforced composites were investigated and compared with those of the gel spun HSPE fiber reinforced composites.

• Korean Journal of Food Science and Technology
• /
• v.29 no.6
• /
• pp.1184-1190
• /
• 1997

Corn zein coated carrageenan films were manufactured by immersing preformed ${\kappa}-carrageenan$ films into solution of different concentrations of corn zein (CZ) solids (10, 20, and 30% in 95% ethyl alcohol) with polyethylene glycol (20% w/w of CZ), glycerol (24% w/w of CZ). For all types of films, water vapor permeability (WVP), water solubility (WS), swelling ratio (SR), tensile strength (TS), percent elongation at break (E), heat sealing strength (HS), and Hunter color values (L, a, and b) were determined. WVP of corn zein coated ${\kappa}-carrageenan$ films decreased significantly (p<0.05) as the concentration of com zein increase. Coating with corn zein also decreased film WS and SR linearly with the concentration of corn zein. TS of corn zein coated carrageenan films decreased linearly with corn zein concentration. All the com rein coated carrageenan films showed heat sealing properties even though their sealing strength was less than half of corn zein film. Obviously corn zein coating affected color of ${\kappa}-carrageenan$ films, which was mainly caused by increase in yellowness (Hunter b-value).

• Polymer(Korea)
• /
• v.32 no.6
• /
• pp.598-602
• /
• 2008

In this study we prepared crosslinked separators with the improved thermal stability by irradiating a commercial polyethylene (PE) separator for lithium secondary battery with an electron beam, and the thermal and mechanical properties of the prepared separators were evaluated as a function of the absorption dose. The thermal shrinkage of electron beam irradiated separator was decreased with increasing absorption dose. As a result of the shutdown behavior using an AC impedance, it was observed that the irradiated separator had the better shutdown function than the unirradiated separator. The modulus of the irradiated separator was enhanced as the absorption dose was increased, while the tensile strength and the break elongation of the irradiated separator were decreased.

• Elastomers and Composites
• /
• v.39 no.4
• /
• pp.301-308
• /
• 2004

Three types of parylene (PA-N, PA-C, PA-D) were used for coating the surface on natural latex rubbers in order to improve surface characteristics including mechanical properties and biocompatibility. The parylene coating was the CVD (chemical vapor deposition) method, and the surface properties of the modified latex were measured. Annealing effects on the mechanical properties of the coated latex were also investigated. The adhesion between latex and parylene was good for all the types of parylene used. As annealing temperature was increased, latex modified with PA-N became more hydrophobic, while the latex treated with PA-C and PA-D became more hydrophilic. As the annealing temperature was raised, the tensile strength was increased, and the elongation was decreased. The biocompatibility was noticeably improved on the latex surface modified with the parylenes through CVD method.

• Journal of Adhesion and Interface
• /
• v.20 no.1
• /
• pp.15-22
• /
• 2019

In this study, polybutadiene based di-functional urethane acrylate oligomer (PB-UAO) were synthesized from polybutadiene diol and isophorone diisocyanate. And then, pressure sensitive adhesive films were prepared by mixing with synthesized oligomer, tri-functional acrylate monomer (Tris(2-acryloyloxyethyl) isocyanurate (TAOEIC) or Trimethylolpropane triacrylate (TMPTA) or Pentaerythritol triacrylate (PETA)), mono-functional acrylate monomer (Stearyl acrylate) and UV initiators. Effects of types and contents of trifunctional acrylate monomers on peel strength, tensile strength, elongation, thermal stability and water absorption property were studied. As the contents of tri-functional acrylate monomer increased, and as the molecular weight of tri-functional acrylate monomer decreased, peel strength, elongation and water absorption showed a tendency to decrease whereas tensile strength and thermal stability showed a tendency to increase.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.24 no.3
• /
• pp.12-17
• /
• 2020

The mechanical properties of the propellant with yellow iron oxide were slightly increased compared to the propellant with red iron oxide. The propellant with yellow iron oxide used two types of AP. As the ratio of small particles of AP increased, the burning rate increased. The propellant may be applied to the propellant under operating conditions of 17.5 mm/sec or less having a pressure index of 0.5. The burning rate downs in the mixer scale-up. The stress at maximum load of propellant decreased and the strain at maximum load increased in the mixer scale-up. The yellow iron oxide did not affect the adhesive force between the insulation/liner/propellant.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.8 no.4
• /
• pp.436-443
• /
• 2020

In this paper, we tried to examine the composition ratio of plastic waste from households according to the generated city and the qualities according to the production time of material recycling products. As a result, the composition ratio of recyclable plastic waste among the total plastic waste according to the generated cities is 64.5~90.4%, showing a big difference by city. In addition, the quality evaluation of material recycling products by production time for four months showed that the average tensile strength was 12.33MPa, the average elongation rate was 5.94%, the average density was 1.35g/㎤ and the average ash content was 3.66%.

• Journal of the Korean Electrochemical Society
• /
• v.17 no.1
• /
• pp.7-12
• /
• 2014

There is increasing demand on the reducing the weight and the volume of the major components in lithium secondary battery to improve energy density. Separator not only provides pathway for lithium ion movement but also prevents direct contact between anode and cathode. Herein we fabricated polyethylene separator by varying biaxial stretching ratio to obtain membrane thickness of 16, 12, and $9{\mu}m$. Mechanical and thermal properties of the separator with different thickness were investigated. Also rate capability and charge-discharge cycle property up to 500 cycles were studied using coin type full-cell with $LiCoO_2$ and graphite as a cathode and an anode, respectively. All the cells using separator with different thickness demonstrated excellent capacity retention after 500cycles (around 80%). Considering the rate capability, cell using separator with thickness of $9{\mu}m$ showed best performance. Interestingly, separator thickness of $9{\mu}m$ was more resistant to heat contraction compared to that of $16{\mu}m$ separator.