• Tunnel and Underground Space
• /
• v.29 no.2
• /
• pp.124-134
• /
• 2019

Subcritical crack growth in rock material can occur under monotonic and cyclic loading. Subcritical crack growth plays an important role in evaluating the long-term stability of structures in rocks. This paper presents the results of studies conducted to determine subcritical crack growth parameters under monotonic and cyclic loading in rock-like material. The constant stress rate method was employed for monotonic loading. The subcritical crack growth parameter of n under cyclic loading was determined by the relation between the rate of crack growth per cycle and stress intensity factor range. The specimens contained pre-existing flaws with 45 and 60 degrees of inclination angle and flaws spacing and continuity were varied to arrange crack growth in shear or tensile manner. The results show that the parameter of n is almost constant regardless of the applied load conditions such as monotonic and cyclic or shear and tension.

• Ecology and Resilient Infrastructure
• /
• v.6 no.1
• /
• pp.12-22
• /
• 2019

This study investigated the spatial and temporal water circulation characteristics of Paldang Reservoir by continuous hydraulic and water temperature survey. Due to differences in water temperature and discharge pattern of Ipo Weir and Cheongpyeong Dam, the flow and temperature fluctuations were different in sections of Namhan River and Bukhan River in Paldang Reservoir. At the stratification period, the water temperature of the discharge of Ipo Weir was higher than that of the Cheongpyeong Dam. Therefore, in the surface layer of the downstream of Bukhan River, relatively high temperature water is located and back water phenomenon occurred, and convergence zone is formed. In the downstream section of Namhan River, low-temperature water was distributed in the middle and lower layers, and the upstream flow appeared to be difficult to mix with the surface layer.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.6 no.4
• /
• pp.365-372
• /
• 2018

3D printing technology of construction field can be divided into structural materials, interior and exterior finishing materials, and is mainly done by extruding and adapting. Particularly when it is applied as an exterior materials, it is mainly applied to an unstructured exterior materials and high accuracy is required. The exterior materials can be used as a cement composite materials, it is suitable also for a additive type manufacturing, and the role of a redispersible polymer powder is important. But, high temperatures, redispersible polymer cement base material beget dehydration and micro crack of cement matrix. In this research, we developed a EVA, EVCL redispersible polymer cement base material applicable as a 3D printing exterior materials, confirmed density and strength characteristics for application as an exterior materials, a flame retardancy test for improving the fire resistance of buildings and confirmed its possibility. From the test result, developed EVCL redispersible polymer cement mortar showed good stability in high temperatures. These high temperature stability is caused by the ethylene-vinyl chloride binding. Thus, this result indicates that it is possible to fire resistant 3D printing interior and exterior finishing materials.

• The Journal of the Korea Contents Association
• /
• v.19 no.5
• /
• pp.64-73
• /
• 2019

This study analyzed the efficiency by using the DEA model to evaluate the competitiveness of specialty construction firms. The target of the analysis is 300 firms with continuous data from 2010 to 2017 as listed and externally listed firms. Significant analysis results are as follows. First, the efficiency of specialty construction firms is lower than that of general construction industry. Second, efficiency by type was highest in facilities construction and dismantling work. This shows that the relevant industries such as reinforced concrete works and scaffolding and demolition work are relatively efficient in specialty construction industry. Third, the efficiency of specialty construction industry is affected by economic fluctuations. When the construction industry is in the expansion phase, the efficiency value is high and the efficiency value is low in the down phase. Finally, in the scale profitability analysis, specialty construction industry was most analyzed by DRS. This means that it is effective to scale down for the efficiency of the firm.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2019.05a
• /
• pp.49-52
• /
• 2019

Braille guide block of sidewalk is an essential facility for independent walking of the blind. The blind walks while checking the braile guide blocks with white cane and sense of sole. When they leave the braile area, they face difficulties until they find the braile guide blocks again. In this paper, we propose an algorithm that guides the walking of the blind by determining whether they follows the braille guide blocks safely. For this purpose, the slope of the braille block is selected as a feature and a 3-line detector is introduced. Also the slopes are stabilized using spatial filtering to deal with breaks or junctions of the braille block during the progress and temporal filtering to cope with ego-motion of the blind. Through simulations using a dataset obtained from the real sidewalks and indoors, it can be shown that the proposed algorithm can successfully estimate the walking direction and determine whether the blind is out of the braille guide block area.

• Ecology and Resilient Infrastructure
• /
• v.7 no.4
• /
• pp.353-365
• /
• 2020

In this study, the characteristics of bed elevation changes of the Nakdong River when weir gates are opened were analyzed using the Hydrologic Engineering Center-River Analysis System (HEC-RAS). The study area was 292.37 km downstream of the Gudam Bridge to the Nakdong estuary of the Nakdong River. The HEC-RAS program, which is a 1D numerical analysis model, was used to simulate bed elevation changes. Simulations were conducted under two scenarios from 2017 to 2019. Scenarios 1 and 2 were devised under the conditions of a fully opened gate and during gate installation, respectively. Results confirmed that, under the conditions of Scenario 1, deposition occurred in most sections from the Hapcheon-Changnyeong weir to the Changnyeong-Haman weir (a distance of approximately 40 km). In addition, it was predicted that the flow that included sediments in the main stream of the Nakdong River was not interrupted by the weir structure and regularly produced changes in the river bed.

• Composites Research
• /
• v.34 no.1
• /
• pp.23-29
• /
• 2021

Commercialized carbon fiber obtained from polyacrylonitrile(PAN) precursor is subjected to oxidation stabilization at 180 to 300℃ in air atmosphere and carbonization process at 1600℃ or lower in inert gas atmosphere. Both of these processes use a lot of time and high energy, but are essential and important for producing high-performance carbon fibers. Therefore, in recent years, an alternative stabilization technology by being assisted with various other energy sources such as plasma, electron beam and microwave which can shorten the process time and lower energy consumption has been studied. In this study, the PAN precursor was stabilized by using plasma treatment and heat treatment continuously. The morphology, structural changes, thermal and physical properties were analyzed using Field emission scanning electron microscopy(FE-SEM), X-ray diffraction(XRD), Fourier transform infrared(FT-IR), Thermogravimetric analysis(TGA) and Favimat.

• Journal of Convergence for Information Technology
• /
• v.10 no.12
• /
• pp.39-48
• /
• 2020

This study is a qualitative study to understand the meaning and essential structure of the experiences of Tae-um (Workplace bullying) experienced in hospital organizations for nurses. The participants were interviewed by selecting 10 persons who agreed to participate in the research through SNS in the workplace with the cooperation of the hospital. The collected data were analyzed using Colaizzi's phenomenological method. As a result of the study, Tae-um in the hospital organization of clinical nurses was divided into 4 categories(Taking the terrible first step, A series of hardships that never end, Hang on to myself, Wings flight of for adaptation) and 16 It was derived from themes. In conclusion, it was confirmed that Tae-um, not only new nurses, but even nurses who have accumulated careers, are still in progress, so they are adapting to the difficult hospital organization. Therefore, if a psychological support program for nurses is introduced, it will contribute to solving the Tae-um problem and establishing an organizational culture where nurses are respected.

• Journal of the Korea Society of Computer and Information
• /
• v.27 no.1
• /
• pp.91-96
• /
• 2022

With the development of the cloud industry, various efforts are being made to improve resource efficiency and environmental continuity in software development and operation methods. However, in constructing a conventional structure of structural scheme, if the functionality is improved and added, it has a problem that the efficiency of full build arrangement is reduced for the changed source. In this paper, if a problem occurs in a solution service company, communication between the development department and the operation department can be facilitated and responded quickly, and the latest source updated during processing of the problem is the management system, provided is a system that can take advantage of CI tools and continuously integrate them. As communication through the proposed system is smooth, it is expected that unnecessary work can be reduced and the speed of development can be improved.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.15 no.2
• /
• pp.89-94
• /
• 2022

In this paper, a discrete-time loop filter(DLF) phase-locked loop with a Frequency Fluctuation Converting Circuit(FFCC) has been proposed. Discrete-time loop filter can improve spur characteristic by connecting the charge pump and voltage oscillator discretely unlike a conventional continuous-time loop filter. The proposed PLL is designed to operate stably by the internal negative feedback loop including the SSC acting as a negative feedback to the discrete-time loop filter of the external negative feedback loop. In addition, the phase noise is further improved by reducing the magnitude of the loop filter output voltage variation through the FFCC. Therefore, the magnitude of jitter has been reduced by 1/3 compared to the conventional structure. The proposed phase locked loop has been simulated with Hspice using the 1.8V 180nm CMOS process.