• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.6
• /
• pp.75-82
• /
• 2021

Low-temperature combustion (LTC) strategies, such as HCCI (Homogeneous Charge Compression Ignition), PCCI (Premixed Charge Compression Ignition), and RCCI (Reactivity Controlled Compression Ignition), have been developed to effectively reduce NOx and PM while increasing the thermal efficiency of diesel engines. Through numerical analysis, this study examined the effects of the injection timing and two-stage injection ratio of diesel fuel, a highly reactive fuel, on the performance and exhaust gas of RCCI engines using gasoline as the low reactive fuel and diesel as the highly reactive fuel. In the case of two-stage injection, combustion slows down if the first injection timing is too advanced. The combustion temperature decreases, resulting in lower combustion performance and an increase in HC and CO. The injection timing of approximately -60°ATDC is considered the optimal injection timing considering the combustion performance, exhaust gas, and maximum pressure rise rate. When the second injection timing was changed during the two-stage injection, considering the combustion performance, exhaust gas, and the maximum pressure increase rate, it was judged to be optimal around -30°ATDC. In the case of two-stage injection, the optimal result was obtained when the first injection amount was set to approximately 60%. Finally, a two-stage injection rather than a single injection was considered more effective on the combustion performance and exhaust gas.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.6
• /
• pp.681-687
• /
• 2014

The objective of this work presented here was focused on analysis of in-cylinder combustion characteristic, engine performance, and nitrogen oxides emission characteristic from marine gas oil for propulsion diesel engine of naval vessels and biodiesel with fuel injection timing in a single cylinder diesel engine. In addition, combustion process was analyzed with a high speed camera of marine gas oil and biodiesel fuel. Retarding the fuel injection timing from $BTDC25^{\circ}CA$ to $BTDC5^{\circ}CA$, in cylinder peak combustion pressure was gradually decreased, however, engine torque showed a tendency to increase. The highest nitrogen oxides level was measured at $BTDC15^{\circ}CA$, they were reduced at retarded and advanced condition on the basis of $BTDC15^{\circ}CA$. Comparing with combustion process of marine gas oil and biodiesel fuel at $BTDC5^{\circ}CA$, self-ignition timing of biodiesel fuel included oxygen content was faster than marine gas oil, however, a cautious observation indicates a slightly higher flame intensity for marin gas oil than biodiesel as a diffusion flame is developing.

• Journal of Power System Engineering
• /
• v.16 no.3
• /
• pp.16-21
• /
• 2012

Biodiesel is technically competitive with or offers technical advantages over conventional petroleum diesel fuel. Biodiesel is an environmentally friendly alternative liquid fuel that can be used in any diesel engine without modification. In this study, to investigate the effect of fuel injection timing on the characteristics of performance with DBF in DI diesel engine. The engine was operated at five different fuel injection timings from BTDC $6^{\circ}$ to $14^{\circ}$ at $2^{\circ}$ intervals and four loads at engine speed of 1800rpm. As a result of experiments in a test engine, maximum cylinder pressure is increased with leading fuel injection timing. Specific fuel oil consumption is indicated the least value at BTDC $14^{\circ}$ of fuel injection timing.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.1
• /
• pp.45-51
• /
• 2015

In order to meet the enforced emission regulations and reduce fuel consumption, various new technologies are employed in engines. The problem of NOx emissions under a lean mixture condition should be solved, because a lean-burn direct-injection engine can realize stable lean combustion with a stratified mixture, which results in improvements in fuel economy and emissions. This study investigated the effects of intake and exhaust valve timing changes on the performance and emission characteristics of a lean-burn LPG direct-injection engine. Under a partial-load operating condition without throttling, an increase in the intake valve opening led to an increase in NOx emissions due to an increase in the amount of excess air. The fuel consumption deteriorated with an increase in the exhaust valve opening due to a decrease in the expansion work and an increase in the pumping loss.

• Journal of Energy Engineering
• /
• v.18 no.2
• /
• pp.136-140
• /
• 2009

Vehicle idle has become an increasing quality concern for automobile manufacturers because of its impact on customer satisfaction. As demand for better fuel economy increases, automobile manufacturers are continuously looking for any benefits from different driving conditions. Combustion variability in spark ignition engines was recognized that the stability of engine at idle is affected by the factors of fuel injection timing, ignition timing and air-fuel ratio. Therefore in this research, the results will be shown the effects of stability and the variations at idle according to fuel injection timing, ignition timing and air-fuel ratio as the basic parameters.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.2
• /
• pp.137-143
• /
• 2012

Currently, in order to meet the reinforced emissions regulations for harmful exhaust gas including carbon dioxide ($CO_2$) as a greenhouse gas, technologies for reducing $CO_2$ emission and fuel consumption are being developed. Gasoline direct injection (GDI) systems have the advantage of improved fuel economy and higher power output than port fuel injection gasoline engine systems. The aim of this study is to examine the performance and emission characteristics of a lean burn GDI engine equipped with spray-guided-type combustion system. Stable lean combustion was achieved with a late fuel injection strategy under a constant operating condition. Further improvement in specific fuel consumption is possible with the introduction of multiple fuel injection strategies, which also increases hydrocarbon (HC) and nitrogen oxide ($NO_x$) emissions and decreases carbon monoxide (CO) emission.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.6
• /
• pp.144-152
• /
• 1996

In the sequential MPI system with one injection for each cycle, engine performance is influenced by the mixture conditions. It can be said that engine performance is improved by being better identical mixture formation conditions for all cylinders. As the fuel injection timing to the intake port effects on the mixture formation conditions and the engine performance, injection timing must be better adjusted to engine requirements. Engine behavior was clearly different depending on the injection time during intake storke. Therefore it was studied that injection timing of fuel effects on the engine performance I. e. combustion stability, COV(imep), A/F excursion, CO,HC emission concentration and fuel consumption. It was found that late intake-synchronous injection was deteriorated the combustion characteristics and performance characteristics, while early intake-synchronous infection resulted in favorable engine behavior.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.4
• /
• pp.417-422
• /
• 2010

Low temperature diesel combustion was achieved via a combination of late injection timing ($8.5^{\circ}$ CA BTDC to $0.5^{\circ}$ CA BTDC) and heavy exhaust gas recirculation (37% to 48%) with ultra low sulfur Swedish diesel fuel in a 1.7L common rail direct injection diesel engine. When injection timing is retarded at a certain exhaust gas recirculation rate, the particulate matter and nitrogen oxides decease simultaneously, while the hydrocarbon and carbon monoxide increase. Hydrocarbon speciation by gas chromatography using a flame ionization detector reveals that the ratio of partially burned hydrocarbon, i.e., mainly alkenes increase as the injection timing is retarded and exhaust gas recirculation is increased. The two most abundant hydrocarbon species are ethene which is a representative species of partially burned hydrocarbons, and n-undecane, which is a representative species of unburned hydrocarbons. They may be used as surrogate hydrocarbon species for performing a bench flow reactor test for catalyst development.

• Journal of the korean Society of Automotive Engineers
• /
• v.11 no.6
• /
• pp.80-88
• /
• 1989

본 연구에서는 양산중인 배기량 2.4Liter, 간접분사방식의 소형 디젤엔진에서 연소방식을 직접 분사방식으로 연소계를 재설계하여, 간접분사방식과 직접분사방식에 따른 엔진성능상의 차이점을 비교 평가하고, 아울러 직접분사방식에서 연소실 형상과 연소 관련 주요 인자들의 변경시 엔 진성은에 미치는 영향에 대해 고찰하였다. 직접분사방식 엔진은 간접분사방식 엔진에 대해 동 일출력, 동일 Smoke 수준인 경우 10-15%의 연료소비 저감의 효과가 있고, 이에 따라 연소관련 부품의 열부하면에서도 유리하였으나, 소음 및 NOx 배출은 증가하는 것으로 나타났다. 직접분사 연소방식에서는 Deep Bowl 연소실 형태의 Cylindrical Type 과 Re-entrant Type 에서 연비와 Smoke 등을 고려한 최적 분사시기가 Re-entrant Type 에서 4.deg. CA정도 늦었으며, 각기 최적 분사시기에서 스옴, NOx를 비교한 결과 Re-entrant Type이 더 우수하였다.

• Journal of the korean Society of Automotive Engineers
• /
• v.9 no.3
• /
• pp.16-22
• /
• 1987

직접분사식 디젤기관의 성능과 배기가스 문제에 여향을 주는 실린더 내에서의 연소형태는 크게 연료분사계와 흡입공기 유동계 두 가지에 의해 결정된다. 즉 분사율, 부사시기, 분무형태와 같은 분사계의 특성과 공기선회, 스퀴시(squish), 난류와 같은 공기 유동 특성에 의하여 연소형태가 결 정된다. 이러한 복잡한 연소형테를 기관 특성에 맞게 조정한다는 것은 대단히 어려운 문제인데 이것은 연료화 공기의 혼합이 연소실형상과 흡기계의 형상에 큰 영향을 받으며 연료가 액체 상 태로 연소실내로 들어와 분무과정을 통하여 증발이 되어야만 연소가 가능하기 때문이다. 특히 흡입공기 유동계에 있어서 현재의 직접 분사식 대젤기관의 흡입구 형상은 흡입공기의 운동에너 지에 모멘트를 가하여 연소실내에서 공기의 선희(swirl)를 발생시켜 줌으로써 연료와 공기의 혼 합기를 형성시키는 Helical type이 많이 이용되고 있다. 그러나 기관 성능과 배기가스 특히 NOx는 상반관계를 이루기 때문에 연소실내로 들어오는 흡입공기의 선희강도(swirl ratio)를 너무 강하게만 한다고 하여 좋은 결과를 얻을 수는 없다. 따라서 설계하고자 하는 각 기관에 있어서 요구되는 성능과 배기가스 문제를 만족하는 흡입공기의 선희강도가 얻어질 수 있도록 흡입구 형상을 설계한다는 것은 많은 연구와 경험이 요구되고 있다. 본 자료에서는 직접분사식 디젤기 관에 있어서 흡입공기의 최적 선희강도에 대한 설정방법과 흡입구 형상 설계를 위한 설계 이론 및 정상류 Rig test상에서의 흡입공기 선희강도의 평가방법을 소개하고자 한다.