• KSBB Journal
• /
• v.14 no.3
• /
• pp.291-296
• /
• 1999

Chiral epoxides are key intermediates for the production of chiral pharmaceuticals, agrochemicals, and functional food additives. Chiral epoxides can be produced by either chemical or biological method. In biocatalytic production routes, chiral epoxides can be produced via epoxidations of prochiral alkenes by monooxygenase or peroxidase. Kinetic resolution of racemic epoxides using whole cells of bacteria or fungi might be commercially useful, since it is possible to obtain chiral epoxides with high optical purities from relatively cheap and readily avaiable racemic epoxides. Some bioprocesses already are commercially developed: the biocatalytic production of chiral epichlorohydrin via microbial stereospecific dehalogenation, and lipase-catalyzed enantioselective hydrolysis in a hollow fiber membrane bioreactor for the production of chiral methyl trans-3-(4-methoxyphenyl)glycidate. the intermediate for calcium antagonist diltiazem. The importance of biocatalytic production of chiral epoxides with several examples from literature are presented.

• Polymer(Korea)
• /
• v.24 no.3
• /
• pp.350-357
• /
• 2000

Curing behaviors of glass/epoxy prepreg for printed circuit boards (PCB) were studied by using dielectrometer and differential scanning calorimeter. This prepreg was showed the lowest ionic viscosity at about 115$^{\circ}C$, and then the ionic viscosity was gradully increased up to 15$0^{\circ}C$. This indicated that the curing reaction of this prepreg started at 115$^{\circ}C$ and the molecular weight was increased by the accelerated thermal cross-linking reaction. The loss factor and tan $\delta$ values were also measured and discussed. The dielectric behaviors of this prepreg system were also measured according to the cure cycle for PCB. This material was found to be thermally stable up to about 30$0^{\circ}C$ and then was showed an abrupt decomposition beyond this temperature.

• Polymer(Korea)
• /
• v.26 no.5
• /
• pp.599-606
• /
• 2002

In this study, 4,4'-tetraglycidyl diaminodiphenyl methane (TGDDM)/polyamideimide (PAI) blends were cured using diaminodiphenyl sulfone (DDS). And the effect of addition of different PAI contents to neat TGDDM was investigated in the thermal, mechanical, and morphological properties of the blends. The cure behavior and thermal stability of the cured specimens were monitored by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA), respectively. Also, the critical stress intensity factor (K$\_$IC/) was measured in UTM, and the phase separation behavior and final morphology of TGDDM/PAI blends were examined in scanning electron microscopy(SEM). As a result, the cure temperature and cure activation energy (E$\_$a/) were decreased with increasing the PAI content. The decreasing of cure temperature and cure activation energy were probably due to the presence of secondary amine group of PAI backbone used as co-initiator. But, the decomposition activation energy (E$\_$t/) and K$\_$IC/ value were increased up to 5. 10 phr of PAI content, respectively and they were decreased above the PAI contents. These results were explained on the basis of chain scission reaction by etherification. And morphology of blends observed from SEM was confirmed in co-continuous structures.

• Applied Chemistry for Engineering
• /
• v.28 no.1
• /
• pp.42-49
• /
• 2017

To replace phthalate plasticizer for PVC, acetylated monoglyceride (AMG) plasticizers were prepared from plant oil and their plasticization effects were also investigated. Transesterification of coconut oil by glycerol followed by acetylation with acetic anhydride gave AMG-CoCo (Coco : Coconut Oil). In addition, AMG-GMO (GMO : Glycerol monooleate) and AMG-GMO-Epoxy were synthesized by acetylation and epoxidation with glycerol monooleate. It was found that the thermal stability of AMG plasticizers increased in the following order: AMG-GMO-Epoxy > AMG-GMO > AMG-CoCo and all three plasticizers were thermally more stable than those of common petroleum-based plasticizer DOP (Dioctyl phthalate). The tensile strain values of the PVC containing AMG compounds were ca. 770~810%, while tensile strength values were ca. 19~22 MPa, which were higher than those of PVC containing DOP. DMA (Dynamic Mechanical Analysis) results showed that the miscibility of AMG-GMO-Epoxy in PVC was excellent and the $T_g$ of PVC containing AMG-GMO-Epoxy at 50 phr decreased down to $24^{\circ}C$. Finally, the leaching experiment result showed that the weight loss values of PVC containing AMG-GMO and AMG-GMO-Epoxy at 50 phr were as low as 2 and 1%, respectively, indicating that they have high water migration resistance. The above findings suggested that AMG-GMO-Epoxy could be one of plant oil-based PVC plasticizers to replace DOP.

• Applied Chemistry for Engineering
• /
• v.10 no.7
• /
• pp.990-995
• /
• 1999

To determine the effect of chemical structure of linear amine curing agents on thermal and mechanical properties, standard epoxy resin DGEBA was cured with ethylene diamine(EDA) and hexamethylene diamine(HMDA) in a stoichiometrically equivalent ratio. From this work, the effect of linear amine curing agents on the thermal and mechanical properties is significantly influenced by the chemical structure or chain length of curing agents. In contrast, the results show that the DGEBA/EDA system having the two carbons had higher values in the thermal stability, maximum conversion of epoxide, density, glass transition temperature, tensile modulus, flexural strength, and flexural modulus than the DGEBA/HMDA system having the six carbons, whereas the DGEBA/EDA cure system had relatively low values in the shrinkage(%), thermal expansion coefficient, tensile strength, and had similar values in the maximum exothermic temperature, and conversion of epoxide compared to the DGEBA/HMDA cure system. This findings indicate that packing ability in the HMDA structure affects the thermal and mechanical properties.

• Composites Research
• /
• v.12 no.3
• /
• pp.84-90
• /
• 1999

High alumina cement(HAC) and polyvinyl alcohol(PVA) based macro-defect-free(MDF) cement composites were reinforced using short carbon fibers, 3mm in length, 1-4% in weight fraction and insoluble polymers such as polyurethane, epoxy, phenol resin, in order to increase mechanical properties and water stability. The specimens were manufactured by the low heat-press(warmpress) method. In addition, the interface and the cross-linking reaction of cement and polymers was also studied by the SEM and TEM. Flexural strength of HAC/PVA based MDF cementitious composites was proportionally decreased with increasing fiber contents due to the undensified structure around fibers. The flexural strength of insoluble polymer added specimen was decreased with increasing fiber contents, while water stability was dramatically improved. Epoxy resin added specimen showed the highest strength with increasing fiber contents, compared with other specimens. The water stability of fiber content 4% added specimen immersed in water presented about 95%, 87% at 3 and 7 days immersed in water, respectively. The interfacial adhesive strength of fiber-matrix was very much improved due to cross linking reaction of polymer and metal ions of cement. Tensile strength of insoluble polymers added composites as linearly increased with increasing the fiber contents. The epoxy resin added specimen also showed highest tensile strength. The 4% fiber added specimen presented 30~80% higher strength than controlled specimen.

• Applied Chemistry for Engineering
• /
• v.30 no.1
• /
• pp.68-73
• /
• 2019

We prepared hydrophobic silica particles by a sol-gel process from tetraethyl orthosilicate (TEOS), followed by coupling the reaction with octyltrimethoxysilane (OTMS) or hexadecyltrimethoxysilane (HDTMS) under various reaction conditions. We confirmed the extent of silica surface modification with organic compounds by SEM-EDS, thermogravimetry and elemental analysis. The silica particles obtained after the hydrolysis reaction of TEOS in ethanol at $50^{\circ}C$ for 24 h and the coupling reaction with OTMS for 2 h at the same temperature displayed the optimum performance in terms of the dispersity in an organic solvent and the surface roughness of films composited with epoxy resins. The oxygen permeability of the composite film with modified-silica was 12% lower than that of using the film without modified-silica.

• Applied Chemistry for Engineering
• /
• v.33 no.6
• /
• pp.574-580
• /
• 2022

While in the process of electroless plating of dendrite-shape copper with silver, various silver-coated copper (Ag@Cu) particles were prepared by using both displacement plating and reducing electroless plating. The physicochemical properties of Ag@Cu particles were analyzed by scanning electron microscope- energy-dispersive X-ray spectroscopy (SEM-EDS), thermogravimetric analysis (TGA), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and Brunauer-Emmett-Teller analysis (BET), and it was confirmed that the silver coated by the reducing electroless plating was formed as nano-particles on the copper surface. Ag@Cu particles were compounded with an epoxy resin to prepare a conductive film, and its thermal stability was evaluated. We investigated the effect of the difference between the displacement plating and reducing electroless plating on the initial resistance and thermal stability of conductive films.

• Journal of the Korean Chemical Society
• /
• v.57 no.6
• /
• pp.738-743
• /
• 2013

Linoleic acid and its metabolites have various medicinal effects with carboxylic acid functional group. General carboxylic acid compounds are discovered as glucuronide metabolites by UGT glucuronosyl transferase at liver. Consequently, glucuronides of linoleic acid metabolites are expected as potent conjugated metabolite. A previous study reported two epoxide metabolites and two dihydroxy metabolites of linoleic acid. There are prepared their glucuronic acid conjugated compounds as potent linoleic acid metabolites.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1998.10a
• /
• pp.130-132
• /
• 1998

정밀여과막(MF)막은 $0.1~1\mum$정도의 공경을 가지고 있는 막으로 산업이나 생활분야에서 널리 사용되고 있다. 이러한 정밀여과막에 이온교환기를 부여 시키므로써, 필요로하는 금속이온이나 단백질을 흡착할 수 있는 기능성 분리막이 제조 가능하다. 방사선프라프트 중합법은 고분자를 개질, 수식 또는 기능화시키는 수법으로 사용되고 있다. 본 실험에서는 방사선그라프트중합법을 사용하여 폴리에틸렌 정밀여과막에 에폭시기를 가지는 glycidyl methacrylate(GMA)를 그라프트 중합시킨 후 이온 교환기를 도입하여, 얻어진 막의 특성에 대해 고찰하였다. 본실험의 목적은 다음과 같다. (1) 폴리에틸렌 정밀여과 막에 방사선그라프트 중합법을 사용하여 이온교환기를 도입시키는 반응조건을 검토한다. (2) 도입된 이온교환기에 다른 막의 투과 성능을 조사한다. (3) 투과법에 의한 금속이온의 흡착성능을 조사한다. 여기서, 이온교환기로서는 술폰산(sodium sulfite:$SO_3H$)을 사용하였다.