• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.11
• /
• pp.61-66
• /
• 2005

This paper describes a 10-bit 210MHz CMOS current-mode Digital-to-Analog Converter (DAC) consisting of 6 bit MSB current cell matrix Sub-DAC, 2 bit mSB unary current source Sub-DAC, and 2 bit LSB binary weighting Sub-DAC for Wireless LAN application. A new deglitch circuit is proposed to control a crossing point of signals and minimize a glitch energy. The proposed 10-bit CMOS current mode DAC was designed by a $0.35{\mu}m$ CMOS double-poly four-metal technology rate of 210MHz, DNL/INL of ${\pm}0.7LSB/{\pm}1.1LSB$, a glitch energy of $76pV{\cdot}sec$, a SNR of 50dB, a SFDR of 53dB at 200MHz sampling clock and power dissipation of 83mW at 3.3V

• Journal of Energy Engineering
• /
• v.14 no.1
• /
• pp.54-61
• /
• 2005

The APR1400 is an Advanced Pressurized Water Reactor with 3983 MWt power, 2×4 loops, and direct vessel injection system. The Fluidic Device (FD) is adopted to regulate the safety injection flow rate in a Safety Injection Tank (SIT) of APR1400. The performance of a newly designed fluidic Device is evaluated by analyzing a Large Break Loss-of-Coolant Accident (LBLOCA) using TRAC-M/F90, version 3.782. The analysis results show that the TRAC-M code reasonably predicts the important phenomena of blowdown, refill and reflood phases of LBLOCA. The sensitivity studies about gas/water volume changes in a SIT and K factor changes in a SI system were also done to understand the important phenomena with a Fluidic Device in APR1400.

• Journal of Energy Engineering
• /
• v.16 no.3
• /
• pp.103-112
• /
• 2007

Flood issue for nuclear power plants designed and built in 1970 is extremely severe for main steam header compartment and main feedwater line region of intermediate building and lower floor. A calculation for flood level at the main feedwater line isolation compartment is now performing by hand calculation. But, this methodology is quite conservative assumption. The goal of this study was to develop method to analyze flowrate using the RETRAN-3D computer code, and the developed method was applied to flood level analysis following main feedwater line break. As a result of analysis, flood level was low remarkably.

• Journal of Energy Engineering
• /
• v.17 no.4
• /
• pp.218-226
• /
• 2008

A component-scale two-phase analysis code has been developed for a realistic simulation of two-phase flow transients in a light water nuclear reactor component. In the code, a two-fluid three-field model is adopted and the governing equations are solved on an unstructured mesh. For the numerical solution scheme, the semi-implicit method used in the RELAP5 code was selected, which has been proved to be very stable and accurate for most of practical applications. However, some modifications were needed for its application to an unstructured non-staggered grid. This paper presents the modified semi-implicit numerical method for unstructured grid and the preliminary results of the calculations.

• Journal of Energy Engineering
• /
• v.20 no.4
• /
• pp.259-266
• /
• 2011

Following the reactor shutdown, the reactor shutdown cooling system must be designed to supply the coolant sufficiently not only to remove the decay heat but to maintain the adequate cooling rate to protect the reactor equipments. In this study, KDESCENT code for the light water reactor and SOPHT, SDCS codes for the heavy water reactor were compared and analyzed to investigate the cooling capability during the shutdown cooling process. The shutdown cooling system design requirements were satisfied during cooling process for both the SDCP and the HTP modes and the design cooling rate of $2.8^{\circ}C/min$ or below was maintained using the SDC heat exchangers. This study shows that the shutdown cooling system in the Wolsong 2, 3, 4 reactors provides sufficient cooling to maintain the nuclear fuel integrity by removing the decay heat of the nuclear fission product.

• Progress in Medical Physics
• /
• v.17 no.4
• /
• pp.224-231
• /
• 2006

The electron energy spectra for 6 MeV electron beam were calculated using a MCNPX code. The head of the linear accelerator (ML6M; Mitsubishi, Japan) was modelled for this study. The energy spectrum of the initial electron beam was assumed to be Gaussian and the mean energy was determined by evaluating the measured and calculated values of $R_{50}$ and dose profiles in air. The energy distributions for electrons and photons at the interested points in the head of the linear accelerator were calculated by appling the Initial beam parameters. The effect of contaminant photons on depth dose curves were estimated by the photon energy spectra at the end of the applicator.

• KIPS Transactions on Software and Data Engineering
• /
• v.5 no.5
• /
• pp.209-220
• /
• 2016

While the services of mobile devices like smart phone, tablet, and smart watch have been increased and varied, the software embedded into such devices has been also increased in size and functional complexity. Therefore, increasing operation time of mobile devices for serviceability became an important issue due to the limitation of battery power. Recent studies focus on the software development having efficient behavioral patterns because the energy consumption of mobile devices is caused by software behaviors which control the hardware operations. However, it is often difficult to develop the embedded software with considering energy-efficiency and behavior optimization due to the short development cycle of the mobile services in many cases. Therefore, this paper proposes the refactoring techniques for reducing energy consumption, and enables to fulfill the energy requirements during software development and maintenance. We defined energy bad smells with the code patterns that can excessively consume the energy, and our refactoring techniques are to remove these bad smells. We performed some case studies to verify the usefulness of our refactoring techniques.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2008.11a
• /
• pp.81-84
• /
• 2008

최근 센서네트워크와 같은 에너지 제한 환경을 위한 경량화 부호화 기술의 필요성이 대두됨에 따라 분산 소스 부호화 기술(Distributed Source Coding)의 응용기술로 비디오 부호화 복잡도의 대부분을 차지하는 움직임 예측/보상과정을 부호화기가 아닌 복호화기에서 수행하는 분산 비디오 부호화 기술(Distributed Video Coding)에 대한 연구가 활발히 이루어져 왔다. 이에 가장 대표적인 기술인 Wyner-Ziv 코딩 기술은 채널 코드를 이용하여 원본 프레임과 이에 대한 복호화기의 예측영상인 보조정보 사이의 잡음을 제거하여 영상을 복원한다. 일반적으로 보조정보는 원본영상에 유사한 키 프레임간의 프레임 보간을 통하여 생성되며 채널 코드는 Shannon limit에 근접한 성능을 보이는 Turbo 코드나 LDPC 코드가 사용된다. 이와 같은 채널 코드의 복호화는 채널 잡음 모델에 기반하여 수행되어지며 Wyner-Ziv 코딩 기술에서는 이 채널 잡음 모델을 '상관 잡음 모델' (Correlation Noise Modeling)이라 하고 일반적으로 Laplacian이나 Gaussian으로 모델화 한다. 하지만 복호화기에는 원본 영상에 대한 정보가 없기 때문에 정확한 상관 잡음 모델을 알 수 없으며 잡음 모델에 대한 예측의 부정확성은 잡음 제거를 위한 패리티 비트의 증가를 야기해 부호화 기술의 압축 성능 저하를 가져온다. 이에 본 논문은 원본 프레임과 보조정보 사이의 잡음을 정확하게 예측하여 잡음을 정정할 수 있는 향상된 상관 잡음 모델을 제안한다. 제안 방법은 잘못된 잡음 예측에 의해 Laplacian 계수가 너무 커지는 것을 방지하면서 영상내의 잡음의 유무에 별다른 영향을 받지 않는 새로운 문턱값을 사용한다. 다양한 영상에 대한 제안 방법의 실험 결과는 평균적으로 약 0.35dB에 해당하는 율-왜곡 성능 향상을 보여주었다.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.49 no.4
• /
• pp.16-22
• /
• 2012

In this paper, the forensic marking algorithm is proposed using psychoacoustic model II and MDCT for high-quality audio. The proposed forensic marking method, that inserts the user fingerprinting code of the audio content into the selected sub-band, in which audio signal energy is lower than the spectrum masking level. In the range of the one frame which has 2,048 samples for FFT of original audio signal, the audio forensic marking is processed in 3 sub-bands. According to the average attack of the fingerprinting codes, one frame's SNR is measured on 100% trace ratio of the collusion codes. When the lower strength 0.1 of the inserted fingerprinting code, SNR is 38.44dB. And in case, the added strength 0.5 of white gaussian noise, SNR is 19.09dB. As a result, it confirms that the proposed audio forensic marking algorithm is maintained the marking robustness of the fingerprinting code and the audio high-quality.

• Journal of Korea Society of Industrial Information Systems
• /
• v.13 no.5
• /
• pp.168-177
• /
• 2008

The code propagation is one of the most important technic for software update in wireless sensor networks. This paper presents a new scheme for code propagation using network coding. The proposed code propagation method roughly shows 20$\sim$25% performance improvement according to network environments in terms of the number of data exchange compared with the previously proposed pipelining scheme. As a result, we can efficiently perform the software update from the viewpoint of speed, energy, and network congestion when the proposed code propagation system is applied. In addition, the proposed system solves the overhearing problems of network coding such as the loss of original messages and decoding error using the predefined message. Therefore, our system allows a software update system to exchange reliable data in wireless sensor networks.