• Journal of Dental Rehabilitation and Applied Science
• /
• v.26 no.1
• /
• pp.1-12
• /
• 2010

The purpose of this study was to compare the strain on the alveolar ridge in the centric, eccentric and protrusive position according to the occlusal scheme (bilateral balanced occlusion with 33 degree anatomical teeth, group B; monoplane occlusion with non-anatomical teeth, group M; lingualized occlusion with 33 degree anatomical teeth and non-anatomical teeth, group L; of complete dentures. Experimental dentures were set bilateral balanced occlusion, lingualized occlusion and monoplane occlusion. They are analysed through T-Scan II(Tekscan, Boston, U.S.A) and 1.5mm thick layer was removed from the denture-supporting surface of resin model and then replaced with silicone to simulate resilient edentulous ridge mucosa. A $4{\times}6$ linear strain gauge is attached to the $1^{st}$ premolar and $1^{st}$ molar area. The strain values are recorded according to the occlusal scheme in the centric, eccentric and protrusive position after uniformly applying 50 N and 150 N force through a Universal Testing Machine(instron$^{(R)}$ 5567, Bluehill 2.0 software ,U.S.A.) with the models mounted in the articulator. When performing centric and protrusive occlusion, the three groups of occlusal scheme were compared in the anterior region and in the posterior region. The strains of each group were also compared in the working side and in the non-working side during eccentric excursion. It was observed that the strain in the bilateral balanced occlusion showed a higher value than the lingualized occlusion and monoplane occlusion in every position except the non-working side. However, during the eccentric movement the strain value in the non-working side showed the lowest value in the bilaterally balanced occlusion. The strain change amount from the working side or centric occlusion to non-working side and also the strain variation rate within the non-working side showed the highest value in bilateral balanced occlusion.

• The korean journal of orthodontics
• /
• v.25 no.3 s.50
• /
• pp.311-321
• /
• 1995

This study was undertaken to investigate the distribution of the chewing side preference and variations in the maximum bite force and facial morphology according to chewing side preference since unilateral chewing may cause morphologic and functional anomalies. 50 dental students who had no signs or symptoms of masticatory system and Angle's Class I relationship in posterior segments were selected, and divided into two groups, that is, 25 in bilateral chewing group(19 male and 6 female) and 25 in unilateral chewing group(10 male and 15 female). Maximum bite force was estimated ana posteroanterior cephalogram were measured ana statistically analyzed. The results were as follows : 1. Their were more students with bilateral chewing side preference($68\%$) and unilateral chewing side group consisted of right side preference($68\%$) and left side preference($32\%$). 2. There was no significant difference in the strength of max. bite force between the right and left side in bilateral chewing group. The bite force of the chewing side nab greater in the unilateral chewing group but less in the non-chewing side compared to those of bilateral chewing group with Bo significant difference. Max. bite force of chewing side was greater than that of non-chewing side in the unilateral chewing group(Female p<0.05). Max. bite force of males was about twice in that of females in both groups(p<0.05). Max. bite force of chewing side of the unilateral chewing group was similar to that of the bilateral chewing group, but that of non-chewing side was less than that of the bilateral chewing group. 3. In comparison of the facial morphology, there was no statistically significant difference in the size between the right and left side of the bilateral chewing group and between chewing and non-chewing side of the unilateral chewing group.

• The Journal of Korean Academy of Prosthodontics
• /
• v.58 no.1
• /
• pp.50-57
• /
• 2020

The loss of posterior support and the abnormal jaw relation can cause pathologic findings. If deep bite patients with multiple missing teeth, can not have the stable posterior contact, the mandible moves posteriorly, and consequently the overjet and overbite get worse. And when the mandibular irregular occlusal plane is corrected, it is easier to have the bilateral balanced occlusion with the maxilla. So the treatment goal is to give proper posetrior support and establish appropriate anterior guidance, and ultimately provide improved mastication and esthetics recovery. In this case, a 68 year old man, having deep bite without posterior support was evaluated by the vertical dimesion decision flow-chart. An available prosthetic height, anterior occlusal relation such as overjet, overbite and the esthetic part such as facial height and the cephalometric analysis are the factors to be considered.

• The Journal of Korean Academy of Prosthodontics
• /
• v.60 no.4
• /
• pp.374-381
• /
• 2022

This case report introduces a 74-year-old male patient who visited retention deficiency of the mandibular implant overdenture, which was fabricated 20 years ago. When the existing dentures were used, the vertical dimension was reduced, the maxillary complete denture lacked lip support and retention, and the mandibular overdenture lacked clip retention due to damage to the bar attachment. After removing the damaged bar attachment, it was replaced with a ball attachment, and impressions were taken using the DENTCA^TM Tray and then the vertical dimension was measured. The gothic arch tracing was performed to record the centric relation. Obtained impressions were scanned and the shape of final dentures was designed using software and try-in dentures were fabricated using 3D printer. After evaluating the occlusal plane, occlusal relationship, facial shape, and pronunciation using the try-in dentures, the bite registration was recorded, and the final denture was manufactured based on this. The inner surface of the denture was adjusted and bilateral balanced occlusion was formed, and the housing was connected to the mandibular denture by a direct method. This case reports have shown satisfactory resultin recovering improved retention and esthetic outcome by increasing the vertical dimension and the lip support using CAD-CAM technique and the ball attachment.

• Journal of Oral Medicine and Pain
• /
• v.32 no.1
• /
• pp.105-111
• /
• 2007

Correlation between occlusal contact pattern and TMD have been hypothesized and partially investigated but results are controversial and not conclusive. The purposes of this study were to compare right-to-left difference of occlusal contact pattern, through contact points, contact force and occlusal balance, in the patients with unilateral TMD and also to evaluate its change related with TMD treatment. 36 patients with unilateral TMD from Department of Oral Medicine in Dankook University Dental Hospital were selected in this study (M:F=7:29, mean age of $29.2{\pm}14.8$ years). A computerized T-Scan II system (Tekscan, INC., USA) was employed for occlusal analysis and the simultaneity and occlusal balance through the number of tooth contact and magnitude of contact force were determined before and after TMD treatment. The number of contact points and contact force was more on the unaffected side than the affected side before treatment (p=0.056 and p=0.060, respectively) while significant difference between both sides was not found after treatment. The number of contact points and contact force on the affected sides significantly increased after treatment (p=0.038 and p=0.052), but the unaffected sides exhibited no significant difference between before and after treatment. In addition, sides difference in relative contact force decreased from about 27% to about 12% after TMD treatment (p=0.001). According to the results of this study, it is likely that unilateral TMD impairs right-to-left occlusal balance and that conservative TMD treatment alleviates the imbalance, subsequently leading to more symmetrical occlusal condition with increased contact points and force.

• Journal of TMJ Balancing Medicine
• /
• v.12 no.1
• /
• pp.28-31
• /
• 2022

위에서 살펴본 바와 같이 나는 급성 턱관절장애의 경우, 첫번째 유형은 주로 턱관절 디스크공간의 문제와 하악의 위치를 바로잡아주는 근육의 문제가 주 원인일 것으로 추정하고 있다. 만약 턱관절 디스크공간이 정상공간이라면 턱의 지그재그 움직임이나 턱관절잡음, 턱통증, 턱탈구, 그리고 개구장애 등이 발생할 수 없기 때문이다. 그리고 근육의 문제 중에서는 턱관절 디스크원판을 양측에서 잡아주는 내외측 익돌근의 문제가 가장 많은 영향을 미치고 있다. 특히 내측 익돌근의 긴장 및 수축이 디스크 원판을 내측으로 빠져나가게 함으로써 하악의 좌우 지그재그 움직임을 야기시키고 턱관절잡음이나 턱통증 및 개구장애를 유발하기 때문이다. 나머지는 저작에 관여하는 근육들이 그 다음으로 영향을 미치는 것으로 예측하고 있다. 그러나 제2형 급성 턱관절장애의 경우는 제1형 급성 턱관절장애가 한단계 더 발전하여 이와 연관된 근육이나 인대의 긴장수축이 오랜 시간 진행되어, 이들이 다시 상부 경추의 아탈구와 두개골의 비정상적 움직임에까지 영향을 미쳐 나타나는 것으로 생각된다. 그렇게 되면 뇌에서 필요 충분한 뇌혈액공급이나 뇌척수액순환의 문제를 일으킬 수 있기 때문이다. 그리고 제1형 만성 턱관절장애의 경우는 제2형 급성 턱관절장애가 좀 더 진행되면서 척추 및 근골격계의 구조변화, 교합 및 턱의 구조변화 그리고 안면구조의 변화에 이르기까지 점점 진행되어 나타나는 것으로 보인다. 따라서 각종 척추 디스크질환, 관절질환을 비롯해서 두개천골계의 순환문제, 부정교합 및 턱 비대칭, 안면 비대칭의 문제를 유발하게 된다고 추정된다. 그러나 두번째 유형의 만성 턱관절장애는, 턱에서 지속적이고 반복적인 그리고 과다한 부정적 자극들이 오랜 기간 누적되면서 턱에 분포된 C 섬유를 비롯한 3차신경의 가소성변화를 유발하면서 결국 중추신경계를 포함하여 전체신경계의 회로망에까지 파급되어 다양한 만성질환 또는 난치성 질환들이 양산되는 것으로 추정하고 있다. 아마도 지금까지 서양의학에서 아직 밝혀내지 못한 대부분의 질병들이 여기에 포함되지 않을까 하는 것이 나의 생각이다.

• The Journal of Korean Academy of Prosthodontics
• /
• v.53 no.1
• /
• pp.19-25
• /
• 2015

Nowadays, CAD/CAM is broadly used in dentistry for inlays, crowns, implant abutments and its spectrum is expanding to complete dentures. Utilizing CAD/CAM to fabricate complete dentures is expected to decrease chair time and the number of visits, thus decreasing total fabrication time, expenses and errors caused during fabrication processes. One of the systems using CAD/CAM, DENTCA$^{TM}$ CAD/CAM denture (DENTCA Inc. Los Angeles, USA) scans edentulous impressions, designs dentures digitally, fabricates try-in dentures by 3D printing and converts them into final dentures. Patients can wear final dentures after only 2 - 3 visits with satisfying adaptation. This case report introduces a 71-year-old male patient who visited to consult remaking of existing old dentures. Residual teeth with bad prognosis and root remnants were extracted and the patient used reformed existing mandibular denture for 2 months. And then DENTCA system started. One-step border molding was done using conventional tray of adequate size provided by DENTCA system and wash impression was taken. Gothic arch tracing was completed based on the vertical dimension of existing dentures. Both maxillary and mandibular trays were placed to the resultant centric relation and bite registration was taken. Then DENTCA scanned the bite registration, arranged the teeth, completed the festooning and fabricated the try-in dentures by 3D printing. The try-in dentures were positioned, occlusal plane and occlusal relations were evaluated. The try-in dentures were converted to final dentures. To create bilateral balanced occlusion, occlusal adjustment was done after clinical remounting using facebow transfer. The result was satisfactory and it was confirmed by patient and operator.

• The Journal of Korean Academy of Prosthodontics
• /
• v.58 no.3
• /
• pp.257-267
• /
• 2020

The goal of suction denture is to enhance retention of dentures by the formation of negative pressure between the denture base and the underlying tissue and sealing around the denture by the mucosa. This patient has been converted to a completely edentulous state after the extraction of residual teeth. Fabrication of suction denture was planned because it was estimated that the conventional compete would be hard to achieve retention due to the absorption of residual ridge and lack of sublingual fold. Through appropriate clinical and laboratory technique such as preliminary impression on the mandibular rest position, provisional vertical dimension determination with Centric Tray^® (Ivoclar Vivadent AG, Schaan, Liechtenstein), closed mouth definitive impression and jaw relation record using individual tray with Gnathometer M^® (Ivoclar Vivadent AG, Schaan, Liechtenstein), artificial teeth arrangement considering stability of the denture, and proper polymerization technique that minimizes polymerization shrinkage, restoring the patient with suction denture resulted in satisfaction throughout the function and asesthetics.