• Journal of the Microelectronics and Packaging Society
• /
• v.7 no.3
• /
• pp.37-44
• /
• 2000

The corrosion behavior of aluminum pad coated with epoxy molding compound (EMC) was investigated using electrochemical impedance spectroscopy (EIS). The impedance change was evaluated by the absorption of deionized water (DI water) to EMC coating and the interface between EMC and aluminum. During the absorption a decrease in resistance and thus an increase in capacitance of EMC as well as the interface of EMC/Al could be observed. Up to about 170 hours of absorption the EMC was saturated with the water molecules and ions generated from EMC. Subsequently the ionic water was penetrated to the interface and finally the corrosion of aluminum was occurred by the Dl water and ions. From measuring the adhesion strength with the Dl water absorption it was expected that the saturation of water and ions in the interface decreased the adhesion strength. The higher filler content of EMC should be necessary to inhibit the corrosion of aluminum electrode in microelectronic packages.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.10
• /
• pp.687-698
• /
• 2001

This paper presents a three dimensional stacked pad area away (PAA) package configuration as an implementation method of radio frequency (RF) circuits. 224MHz RF circuits of intelligence traffic system(ITS) were constructed with the stacked PAA RF pakage configuration. In the process of manufacturing the stacked PAA RF pakage, RF circuits were partitioned to subareas following their function and operating frequency. Each area of circuits separated to each subunits. The operating characteristics of RF PAA package module and the electrical properties of each subunits were examined. The measurement of electrical parameters for solder balls which were interconnects for stacked PAA RF packages showed that the parasitic capacitance and inductance were 30fF and 120pH, respectively, which might be negligible in PAA RF packaging system. HP 4396B network/spectrum analyzer revealed that the amplification gain of a receiver and transmitter at 224 MHz was 22dB and 27dB, respectively. The gain was 3dB lower than designed values. The difference was probably generated from fabrication process of the circuits by employing commercial standard

• Archives of design research
• /
• v.17 no.4
• /
• pp.97-106
• /
• 2004

Oukjuk becomes to known to the people and valuates due to the importance of the effect of the medicine. Known as taoist hermit plant, Oukjuk tea has called as a Solomon's Seal Tea in the western countries. Dissimilarly from other herb teas, it contains a high percentage of minerals. Because of the utility value of this, people used to use Oukjuk as an oriental medical treatment for various kinds of the condition of illness as for nutritive food or tonic material. According to the records, a sage of old or people seeking after truth had enjoyed the tea very much. In spite of these all effects, public has only a superficial understanding of the matter, Comprehending the problems, this study analyses ways and means of the functional packaging for the Solomon's Seal tea. In this research, the most problems came out with the quality of the products and the level of their packaging which is not variously in forms and not properly developed in materials and designs. As a conclusion the paper pointed out the importance of keeping the traditional high quality in product and having an appeal to packaging for customer's needs.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.2
• /
• pp.688-695
• /
• 2013

This article is focused to examine the influence of relationship between additional costs and repurchase in the outbound package tourists regard to the role of the personal service and brand. It is analysed that the additional costs don't have an effect on the repurchase. And also there is no relationship between repurchase and personal service for the tourists. However the role of the brand plays a mediated effect in repurchase in the outbound markets. Nonetheless the manager and contact employee of travel agents have an attention to the personal service quality and brand as well.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1611_1612
• /
• 2009

접합온도의 증가는 PN 접합 부분에서 생성된 열이 외부로 원활하게 방출되는 것을 저하시키고, 칩 내부에 남은 열이 전자와 정공의 비발광 재결합을 증가시켜 LED의 신뢰성과 내구성에 큰 영향을 미친다. 본 논문에서는 PMS-50과 KEITHLEY 2430을 이용하여 FR4 PCB의 Via hole 구성에 따른 LED 패키지의 열적 광학적 특성을 분석하였다. Via hole 0.6 [mm]일 때 열 특성과 광 출력 특성이 가장 우수하였으며 Via hole 1.2 [mm]는 열 특성, 광 특성이 가장 떨어졌고, 열 특성은 곧바로 광 특성에 영향을 미치는 것을 알 수 있었다.

• The monthly packaging world
• /
• s.358
• /
• pp.48-64
• /
• 2023

산업통상자원부가 주최하고 한국디자인진흥원이 주관하는 우수디자인(GD)상품 선정은 산업디자인진흥법에 의거해 1985년부터 매년 시행되고 있으며, 우수디자인 상품과 서비스에 GD(Good Design)마크를 부여하는 제도이다. 2022년에는 1,481점이 출품, 총 549점이 GD로 선정되었으며, 이 중 대상, 금상, 은상, 동상 등 총 79점이 수상의 영광을 안았다. 이 중 포장 관련 디자인은 시각/정보 디자인 부문 내 패키지 디자인 분야 외에도 다수의 분야에서 49개 상품이 선정됐다. 올해 수상작을 살펴보면, 알아보기 쉬운 디자인과 더불어 친환경이 강조되고 있음을 알 수 있다. 이는 전 세계적 흐름에 맞춘 것으로 소재가 재생 유리나 종이 등 재활용됐거나 환경을 고려하여 만들어진 패키지가 눈에 많이 띈다. 수상작 중에는 우리나라 고유의 멋을 보여준 디자인 제품들이 우수한 평가를 받았다. 특히, 주식회사 밝은무역의 '우리 앞바다에 잡은'은 전통 문양을 활용한 디자인으로 포장 부문 최고상인 은상을 수상했다. 그 외에도 (주)에스피씨삼립과 담양제과 또한 한국적이면서도 깔끔하고 모던한 느낌의 디자인으로 동상을 수상했다. 지면에서는 2022년 우수디자인으로 선정된 포장 관련 상품들을 자세히 살펴보도록 한다.

• Journal of the Microelectronics and Packaging Society
• /
• v.17 no.2
• /
• pp.21-28
• /
• 2010

Creep behaviors of the solder balls in a flip chip package assembly during thermal cycling test is investigated.. A material models used in the finite element analysis are viscoplastic model introduced by Anand and creep model called partitioned model. Experiment of two temperature cycles using moir$\acute{e}$ interferometry is conducted to verify the reliability of material models for the analysis of thermo-mechanical behavior. Bending deformations of the assemblies and average strains of the solder balls due to temperature change and dwell time are investigated. The results show that time-dependent shear strain of solder by the partitioned model is in excellent agreement with those by moir$\acute{e}$ interferometry, while there is considerable difference between results by Anand model and experiment. In this paper, the partitioned model is employed for the time-dependent creep analysis of the FC-PBGA package. It is also shown that the thermo-mechanical stress becomes relaxed by creep behavior at high temperature during temperature cycles.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.3
• /
• pp.1414-1423
• /
• 2014

This paper aims to analyze destination composition patterns included in package products and to identify the characteristics of the tourism destinations through social network analysis using data collected from tour packages distributed by major Korean travel agencies, targeting Singapore as a key destination. Such tour package data were transcribed into data matrix using Pajek, UCINET, and Cytoscape for analysis. The density and centralization scores derived from the analysis indicated clearly that each destination was almost connected to each other. The centrality scores indicated that the destinations with higher degree of centrality also has higher betweenness centrality within the network. Based on centrality scores, POI(point of interests) of tourism destinations showed concentration in southern area of the target region. Finally, through component analysis, subgroups of tourism destination networks are isolated. Practical implications were also presented for industry practitioners.

• Journal of Nutrition and Health
• /
• v.51 no.5
• /
• pp.480-487
• /
• 2018

Purpose: The study examined the Chinese and Japanese consumers' preference for Korean home meal replacement (HMR) product package designs using conjoint analysis. Methods: The questionnaire survey was completed by 270 consumers living in Beijing, China and Osaka, Japan, over the age of 20 years old, who had previously purchased or consumed a Korean HMR. Based on the attributes and levels within each attribute related to the Korean HMR product package design, 54 profiles were constructed. Of the 54 profiles, 11 combinations were selected using an orthogonal design, and the participants were asked to rank the 11 combinations in order of preference from top to bottom. Results: The relative importance of the Korean HMR product package design attributes were analyzed. Chinese consumers regarded illustration, ingestion form, concept, and brand name, in that order, to be most important. In the case of Japanese consumers, illustration, concept, ingestion form, and brand name, in that order, were most important. For the illustration attributes, in order of importance, Chinese consumers preferred raw materials, characters, and celebrities, and Japanese consumers preferred characters, raw materials, and celebrities. For the concept attributes, Chinese consumers favored, witty, traditional Korean, and modern concepts, whereas Japanese consumers favored witty, modern, and then traditional Korean concepts. For the ingestion form attributes, both Chinese and Japanese consumers preferred Ready To Eat (RTE), followed by Ready To Heat (RTH), and then Ready To Cook (RTC). For the brand name attributes, both Chinese and Japanese consumers preferred the localized brand name over the Korean brand name. Conclusion: Differences in the relative importance of Korean HMR product package design attributes were observed among Chinese and Japanese consumers, and there were differences in preference according to the levels within each attribute. These results are expected to provide useful basic data to assist in the future development of differentiated HMR package designs and marketing strategies to meet consumer needs in the market for Korean HMR in China and Japan.

• Korean Journal of Optics and Photonics
• /
• v.18 no.4
• /
• pp.264-269
• /
• 2007

Today's research has been focused on changing the light source from filament to LED for luminarie illumination to overcome the shortcoming of a filament. The purpose of this research is to make an appropriate high power LED package structure for luminarie. We simulated radiation patterns of the various structures by the ray tracing simulator (Light Tools), and also analyzed the radiation patterns using an LED test system (OL770). As we increased an inner reflector angle, the radiation pattern split into two peaks and the angle between two peaks became larger. In addition, when we increased an outer reflector angle, the angle between side peaks gradually decreased, while it increased again when the angle reach $50^{\circ}$. These results could be understood from the ray tracing of the light reflected from two reflectors. We made the high power LED package for luminarie on the condition of the optimized structure which was made by ray tracing simulation results, and we measured the radiation patterns by using an LED test system, and these results were well matched to the simulation results.