• Journal of the Korean Geotechnical Society
• /
• v.15 no.4
• /
• pp.113-132
• /
• 1999

Recently in Korea, application of the soil nailing is gradually extended to the sites of excavations and slopes having various ground conditions and field characteristics. Design of the soil nailing is generally carried out in two steps, The First step is to examine the minimum safety factor against a sliding of the reinforced nailed-soil mass based on the limit equilibrium approach, and the second step is to check the maximum displacement expected to occur at facing using the numerical analysis technique. However, design parameters related to the soil nailing system are so various that a reliable design method considering interrelationships between these design parameters is continuously necessary. Additionally, taking into account the anisotropic characteristics of in-situ grounds, disturbances in collecting the soil samples and errors in measurements, a systematic analysis of the field measurement data as well as a rational technique of the optimum design is required to improve with respect to economical efficiency. As a part of these purposes, in the present study, a procedure for the optimum design of a soil nailing excavation wall system is proposed. Focusing on a minimization of the expenses in construction, the optimum design procedure is formulated based on the genetic algorithm. Neural network theory is further adopted in predicting the maximum horizontal displacement at a shotcrete facing. Using the proposed procedure, various effects of relevant design parameters are also analyzed. Finally, an optimized design section is compared with the existing design section at the excavation site being constructed, in order to verify a validity of the proposed procedure.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.25 no.3
• /
• pp.55-62
• /
• 2017

In this study, we investigated the effect of seaweed (SW) addition on the anaerobic digestion of food waste (FW). Anaerobic batch experiments were carried out at various substrate concentrations (2.5 to 10.0 g VS/L) and mixing ratios (FW:SW=100:0, 75:25, 50:50, 25:75 and 0:100 on VS basis) of FW and SW. The methane yield of FW alone was 394, 377, 276, $49mL\;CH_4/g\;VS_{added}$ at each substrate concentration (2.5 to 10.0 g VS/L). In cases of co-digestion, methane yield decreased (up to 15 %) with increasing mixing ratio of SW at low substrate concentration (2.5 to 5.0 g VS/L), while it increased (up to 240 %) at high substrate concentration (7.5 to 10.0 g VS/L). The synergistic effect was calculated based on the amount of methane generated from the single-feedstock digestion of FW and SW. The synergistic effect was not found at 2.5 and 5.0 g VS/L. However, the synergistic effect increased (up to 25% = synergistic increment/total methane production at 10.0 g VS/L, FW:SW=50:50) with increasing the ratio of seaweed at 7.5 and 10.0 g VS/L. At 10.0 g VS/L of FW alone, the accumulated amount of organic acids was 7,426 mg COD/L, which was decreased to 2,346 mg COD/L by seaweed (FW:SW=50:50) addition. The reason for the synergistic effect was to control the production rate of the organic acids by adding SW that has a relatively lower biodegradability compared to FW.

• Journal of Environmental Policy
• /
• v.14 no.2
• /
• pp.149-170
• /
• 2015

The purpose of this paper is to figure out the research direction and information regarding Mt. Baekdu in Korea through analyses of the research field and trends. Firstly, we made inventory of journal papers, conference proceedings, and research reports published related to Mt. Baekdu. A total of 255 data, spanning the 34 years from the 1980s to the middle of 2014, were acquired and classified into categories according to the year, field, contents and study area. Results show that research on Mt. Baekdu has been performed more than twice since 2010 and study regarding prediction has been carried out in 54.7% cases. In addition, the importance of geo-spatial information is expected to increase in order to study Mt. Baekdu. Secondly, we made and analyzed a geospatial information using inventory of 234 detailed research contents in research reports by Korea Meteorological Administration (KMA) and National Institute of Meteorological Research (NIMR). Statistics on categories show that research regarding prediction accounted for 81.6% of cases and the study of geo-spatial information utilization accounted for 54.7% of cases. However, the focus on studying the Mt. Baekdu region accounted for only 20.1% of cases. Thus, this indicates that it is necessary to do research at Mt. Bakdu itself. If the directly available geo-spatial information system is developed related to Mt. Baekdu, it will save research costs and analysis time. This study can be used to manage information about the research field of Mt. Baekdu by analysing inventory of research references and geospatial information using inventories when the Mt. Baekdu area is the focus of future research.

• Archives of design research
• /
• v.19 no.1 s.63
• /
• pp.293-302
• /
• 2006

clay cups with handles made in studios in Korea and the United States were selected and analyzed. The shape of cup were fixed to ensure proper comparison between handle size of the cup and position. The variable factors were the thickness of the handle, the number of fingers required to hold the cup, the relationship between the handle's shape and the position of its attachment to the cup, the effect of the handle's setter, the change in shape of the handle's thickness, and the relationship between the cup's weight center and handle. Preference test were designed and tested to the users, and the results were analyzed. The results showed that to make a comfortable handle, it is important to incorporate the shape of the resting hand in the design of the handle. Specifically, the design should be such that the cup can be held comfortably. This is possible if the weight of the cup is spread evenly when several fingers are inside the handle's curve and if such factors as the hand size, the curve of the fingers, and the position that best controls the cup's weight center are carefully considered. At this time, if there is a setter for the thumb, a cup of the same weight can be lifted more lightly. In the design of such a cup, the oval line is drawn by extending the cup's handle toward the direction of the cup's body. If the cup's weight center is located on the oval line, the cup's handle may be said to be effective. In such a case, the nearer the handle is to the cup's body weight center, the less power is needed to lift the cup efficiently. Our test results can be applied as a powerful tools in design and manufacturing cups with handle in terms of artistry and functionality.

• Journal of Food Hygiene and Safety
• /
• v.20 no.1
• /
• pp.22-35
• /
• 2005

A survey was conducted to investigate the perception of food sanitation officers toward the Genetically Modified Foods. They were mainly from Regional Agencies of KFDA, City/Province office, and National quarantine station. Some of them were professors of university and researchers of research institute. Most of respondents had experiences of hearing or reading GM foods (over $95\%$) and over $90\%$ of respondents much needed the label of GM foods. Although some of officers of city/province office and national quarantine station showed less knowledge than other respondent groups, most of respondents had basic knowledge about biology. The frequency of respondents worked over 20 years and worked in the general administration was higher than that of other groups in the question of unsafe of GM foods. The answer frequency of careless treatment of foods was highest in the question of risk factor, and the frequency of GM foods was lowest ($4.4\%$). It was concluded that food sanitation officers had positive opinion about GM foods, but there were some differences in the knowledge among agencies. Therefore, it is necessary more educations and informations are needed for food sanitation officers.

• Journal of Venture Innovation
• /
• v.1 no.1
• /
• pp.83-98
• /
• 2018

This paper makes a theoretical approach to the differences between transaction tax and capital gains tax when the financial instruments are traded and imposed taxes in K-OTC market, a newly emerging off-board market. Since it is difficult to reduce risk to the level which investors would like to pursue - depending on the taxation methods of portfolio-composed financial instruments - when it comes to forming a synthetic bond to hedge risk, this paper also seeks for effective taxation methods to make this applicable. First of all, to thoroughly review the taxation balance of synthetic bonds, this paper analyzed the effects of the transaction tax and capital gains tax imposed upon synthetic bonds according to the changes in final stock price and strike price in K-OTC market, and analyzed after-tax profit differences among them depending on whether income tax deduction took place or not. As a result of the research upon the tax gap in transaction tax and capital gains tax according to the changes of final stock prices, it was shown that imposing transaction tax is more likely to be effective for some level of risk hedging with replicating portfolio considering taxation policies and financial markets, since the effect of the transaction tax has a much lower tax gap than that of capital gains tax. In addition, in relation to whether income tax deduction was permitted or not, it was proved that the effect of the transaction tax and the capital gains tax vary depending on the variation in the strike price. Above all, it was shown that if the strike price is lower than the stock price, the transaction tax will be less affected by the existence of income tax deduction than the capital gains tax, while both will be equally affected by the existence of income tax deduction if the strike price is higher than the stock price. Further study would be to demonstrate the validation of this in the K-OTC market with actual financial instruments and, also, to seek for a more systematic hedging method by using a ratio analysis approach to the calculation of the option transaction tax

• Korean Journal of Clinical Laboratory Science
• /
• v.49 no.3
• /
• pp.300-307
• /
• 2017

Electroencephalography (EEG) is distinct from other medical imaging tests in that it is a functional test that helps to diagnosis disorders related to the brain, such as epilepsy. The most important abilities for a medical technologist when performing an EEG are knowing the exact location of the electrode and recording the EEG wave clearly, except for artifacts. Although theoretical education and practical training are both included in the curriculum for improving these abilities, sufficient practical training has been lacking due to problems like expensive equipment and insufficient practical training time. We try to solve these issues by manufacturing the training 10-20 electrode system and by estimating the efficiency and satisfaction of the training 10-20 electrode system through a questionnaire. The time required for practical training using this system was $43.58{\pm}9.647min$, which proved to be efficient. The satisfaction score of participants who experienced curriculum practical training was improved from $7.21{\pm}2.285$ to $9.46{\pm}1.166$. Based on these findings, it is considered that practical training via the use of the training 10-20 electrode system will solve the problems, such as lack of equipment and insufficient practical training time. Nonetheless, to further improve the training 10-20 electrode system, it must overcome the limitations of developing a device capable of checking the actual brain waves and validating the exact location of electrode attachment.

• Journal of KIISE:Computing Practices and Letters
• /
• v.16 no.12
• /
• pp.1141-1153
• /
• 2010

This paper introduces ONLIS(Overlay Multicast Network for Live IPTV Service), a novel overlay multicast network optimized to deliver live broadcast IPTV stream. We analyzed IPTV reference model of ITU-T IPTV standardization group in terms of network and stream delivery from the source networks to the customer networks. Based on the analysis, we divide IPTV reference model into 3 networks; source network, core network and access network, ION(Infrastructure-based Overlay Multicast Network) is employed for the source and core networks and PON(P2P-based Overlay Multicast Network) is applied to the access networks. ION provides an efficient, reliable and stable stream distribution with very negligible delay while PON provides bandwidth efficient and cost effective streaming with a little tolerable delay. The most important challenge in live P2P streaming is to reduce end-to-end delay without sacrificing stream quality. Actually, there is always a trade-off between delay & stream quality in conventional live P2P streaming system. To solve this problem, we propose two approaches. Firstly, we propose DSPT(Distributed Streaming P2P Tree) which takes advantage of combinational overlay multicasting. In DSPT, a peer doesn't fully rely on SP(Supplying Peer) to get the live stream, but it cooperates with its local ANR(Access Network Relay) to reduce delay and improve stream quality. When RP detects bandwidth drop in SP, it immediately switches the connection from SP to ANR and continues to receive stream without any packet loss. DSPT uses distributed P2P streaming technique to let the peer share the stream to the extent of its available bandwidth. This means, if RP can't receive the whole stream from SP due to lack of SP's uploading bandwidth, then it receives only partial stream from SP and the rest from the ANR. The proposed distributed P2P streaming improves P2P networking efficiency.

• Journal of KIISE:Computer Systems and Theory
• /
• v.34 no.5_6
• /
• pp.257-266
• /
• 2007

In On-Chip bus, the arbitration scheme is one of the critical factors that decide the overall system performance. The arbitration scheme used in traditional shared bus is the master-side arbitration based on the request and grant signals between multiple masters and single arbiter. In the case of the master-side arbitration, only one master and one slave can transfer the data at a time. Therefore the throughput of total bus system and the utilization of resources are decreased in the master-side arbitration. However in the slave-side arbitration, there is an arbiter at each slave port and the master just starts a transaction and waits for the slave response to proceed to the next transfer. Thus, the unit of arbitration can be a transaction or a transfer. Besides the throughput of total bus system and the utilization of resources are increased since the multiple masters can simultaneously perform transfers with independent slaves. In this paper, we implement and analyze the arbitration schemes for the Multi-Layer AHB BusMatrix based on the slave-side arbitration. We implement the slave-side arbitration schemes based on fixed priority, round robin and dynamic priority and accomplish the performance simulation to compare and analyze the performance of each arbitration scheme according to the characteristics of the master and slave. With the performance simulation, we observed that when there are few masters on critical path in a bus system, the arbitration scheme based on dynamic priority shows the maximum performance and in other cases, the arbitration scheme based on round robin shows the highest performance. In addition, the arbitration scheme with transaction based multiplexing shows higher performance than the same arbitration scheme with single transfer based switching in an application with frequent accesses to the long latency devices or memories such as SDRAM. The improvements of the arbitration scheme with transaction based multiplexing are 26%, 42% and 51%, respectively when the latency times of SDRAM are 1, 2 and 3 clock cycles.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.36 no.1
• /
• pp.65-74
• /
• 2016

This study mainly focuses on urban regeneration project as a countermeasure to resolve climate change issues by analyzing the carbon-reduction effect of Jeonju test-bed cases. First, an urban regeneration project is designed for city, Jeonju by analyzing its environmental problems and potential improvement. Then, carbon emission and reduction amounts are evaluated for different businesses and scenarios. Carbon emission sources are classified according to a standard suggested by IPCC, and the emissions are calculated by various standard methods. The result shows that carbon emission amount in Jeonju test-bed is 102,149 tCO2eq. The fact that 70% of the emission from energy sector originates from buildings implies that urban regeneration projects can concentrate on building portions to effectively reduce carbon emission. It is also projected carbon emission will decrease by 3,826tCo2eq in 2020 compared to 2011, reduction mainly based on overall population and industry shrinkage. When urban regeneration projects are applied to 5 urban sectors (urban environment, land use, green transportation, low carbon energy, and green buildings) total of 10,628tCO2eq is reduced and 4,857tCO2 (=15.47%) when only applied to the green building sector. Moreover, different carbon reduction scenarios are set up to meet each goal of different sectors. The result shows that scenario A, B, and C each has 5%, 11%, and 15% of carbon reduction, respectively. It is recommended to apply scenario B to achieve 11% reduction goal in a long term. Therefore, this research can be a valuable guideline for planning future urban regeneration projects and relative policies by analyzing the present urban issues and suggesting improvement directions.