• 멤브레인
• /
• 제11권3호
• /
• pp.124-132
• /
• 2001

고온에서 수소 분리 회수를 목적으로 silica/alumina 복합 막을 합성하였다. 막의 선택 투과 성능을 향상시키기 위해, sol-gel법에 의한 silica 및 alumina층을 중간층으로 도입하고, 그 위에 강제유동 CVD법에 의한 silica를 합성하였다. Sol-gel법에 의해 ${\alpha}$-alumina tube에 합성한 ${\gamma}$-alumina 및 silica 막은 Knudsen 확산 영역의 많은 mesopore를 포함하고 있어서 수소 선택 분리 막으로는 적합하지 못했다. 하지만, sol-gel법에 의해 합성한 silica/${\gamma}$-alumina층에 강제유동 CVD법으로 silica를 합성한 결과, 질소 투과 영역의 세공이 완전히 제거되어, 높은 수소 선택성을 가지는 복합 막이 형성되었다. 그 막은 온도에 따라 수소 투과 속도가 증가하여 $450^{\circ}C$에서 $5.57{\times}10^{-8}molm^2s^LPa^1$의 수소 투과 속도와, 9.52 kJ/mol의 활성화 에너지를 나타냈다. 분자체 효과에 의해 질소 투과가 완전히 배제되고, 수소만 선택적으로 투과되는 silica/alumina 복합막이 성공적으로 합성된다.

• 한국수소및신에너지학회논문집
• /
• 제29권2호
• /
• pp.155-162
• /
• 2018

In this paper, the reliability of the numerical analysis using the two phase flow on the behavior of the hydrogen bubbles in the alkali electrolysis stacks was investigated by comparing the results obtained from numerical analysis and flow visualization experiments. As the results, through comparison with results gotten to visualization experiments, it is possible to approximate analysis for the flow of hydrogen bubbles in the stacks by numerical analysis using the two-phase flow. Also, the flow of hydrogen bubbles around the electrodes could be similarly analyzed by numerical analysis using the two-phase flow.

• 한국수소및신에너지학회논문집
• /
• 제32권5호
• /
• pp.347-355
• /
• 2021

This paper is a study on the thermal design of printed circuit heat exchanger (PCHE) to supply cryogenic high pressure liquid hydrogen stored from hydrogen liquefaction process by using computational fluid dynamics (CFD). This PCHE should be thermally designed to raise the temperature of cryogenic liquid hydrogen to a desired temperature and also to be anti-icing to avoid any local freezing in hot channel. This research presents the effect of inlet velocity and inlet temperature of hydrogen, and the effect of flow configurations of co/counter-flow on thermal design of PCHE heat exchanger based on various CFD simulation analysis.

• 한국수소및신에너지학회논문집
• /
• 제33권5호
• /
• pp.525-533
• /
• 2022

In this study, in order to numerically analyze the heat flow characteristics in the valve according to the opening rate for the solenoid valve for hydrogen supply applied to the hydrogen storage tank, flow characteristics were comparatively analyzed. Through the analysis of pressure and temperature distributions within the valve according to the high-pressure supply condition of 70 MPa or more, the heat flow characteristics in the valve, inlet and outlet passage according to the opening rate of the valve were identified. As a result a sudden change in the fluid behavior appears in the neck region of the valve, and it is understood that the flow separation caused by the flow path shape of the expanded tube has a dominant influence on the flow characteristics. And, it was confirmed that the shape of the valve seat is a factor significantly affecting the improvement of flow rate and differential pressure performance.

• 한국수소및신에너지학회논문집
• /
• 제34권5호
• /
• pp.514-525
• /
• 2023

This study conducted numerical simulations with the purpose of analyzing the impact of variations in outlet pressure conditions under extreme temperature conditions on the fluid dynamics and performance of a check valve utilized in hydrogen refueling systems. Under the extreme temperature conditions, changes in outlet pressure conditions of the check valve were investigated to analyze velocity distributions, pressure distributions, and temperature distributions in the operational and connection regions. The analysis results indicated that changes in outlet pressure had a significant influence on the internal temperature variation of the check valve. Furthermore, due to density variations in the connection region caused by the cooling effect of excessively cooled hydrogen, a bias in the primary flow direction towards the lower part of the valve outlet was observed in the outlet area. Through a comparison of the results of the valve's inherent flow performance, represented by the flow coefficient, it was observed that when the pressure difference between the inlet and outlet was below 0.37 MPa, sufficient flow was not ensured.

• 한국정보처리학회:학술대회논문집
• /
• 한국정보처리학회 2023년도 추계학술발표대회
• /
• pp.681-684
• /
• 2023

우리나라의 수소연료전지 차량의 점유율이 매년 증가하고 있으나, 수소충전소 설비의 잦은 중단으로 수소연료전지 차량 운전자들이 제때 차량을 충전하지 못하는 불편이 발생하고 있다. 본 논문에서는 수소충전소 설비 중 Diaphragm을 사용하는 압축기의 이상 패턴을 탐지하는 Ensemble 모델을 통해 수소충전소에서 2023년 1월 1일부터 2023년 6월 28일 동안 수집된 데이터를 분석하였으며, 해당 기간 동안 발생했던 고장에 대해 2일전부터 이상 패턴이 10,000 이상 탐지되는 결과를 얻었다.

• 한국수소및신에너지학회논문집
• /
• 제28권1호
• /
• pp.85-91
• /
• 2017

To develop a pressurized chemical looping combustor, effect of pressure on minimum fluidization velocity and transition velocity to fast fluidization was investigated in a two-interconnected pressurized fluidized bed system using oxygen carrier particle. The minimum fluidization velocity was measured by bed pressure drop measurement with variation of gas velocity. The measured minimum fluidization velocity decreased as the pressure increased. The transition velocity to fast fluidization was measured by emptying time method and decreased as the pressure increased. Gas velocity in the fuel reactor should be greater than the minimum fluidization velocity and gas velocity in the air reactor should be greater than the transition velocity to fast fluidization to ensure proper operation of two interconnected fluidized bed system.

• 한국수소및신에너지학회논문집
• /
• 제29권4호
• /
• pp.370-377
• /
• 2018

Ball valve has been widely used in the field of high-pressure gas pipeline as an important component because of its low flow resistance and good leakage performance. The present paper focuses on the flow nature at the downstream of the ball valve used for gas pipelines according to valve opening rates. Steady 3-D RANS equations, SC/Tetra, have been introduced to analyze the flow characteristics inside the ball valve. Numerical boundary conditions at the inlet and outlet of the valve system are imposed by mass flow-rate and pressure, respectively. Velocity distributions obtained by numerical simulation are compared with respect to the valve opening rates of 30, 50, and 70%. Cavity distributions, asymmetry flow velocity and the flow stabilization point at each opening rate are also compared. When the valve opening rates are 30 and 50%, the flow stabilization requires the sufficient length of 10D or more due to the influence of the recirculation flow at the downstream of the valve.

• 한국수소및신에너지학회논문집
• /
• 제26권4호
• /
• pp.386-392
• /
• 2015

Flow characteristics inside a 10 inch ball valve have been analyzed using three-dimensional numerical analysis and experiments. Continuity and three-dimensional Reynolds-averaged Navier-Stokes equations have been used as governing equations for the numerical analysis. The numerical model has been constructed through the grid dependency test and validation with the results of experiments to ensure reliability and numerical effectiveness. The shear stress transport (SST) model has been used as the turbulence closure. The experimental test-rig has been constructed to measure pressure, temperature and flow rate along the pipeline. Some valve opening angles have been tested to evaluate the flow characteristics inside the ball valve and pipeline. The results show that the rapid pressure variations is observed while the valve opening angle decreases, which caused by flow separation at the downstream of the ball valve.

• 한국추진공학회지
• /
• 제17권3호
• /
• pp.21-29
• /
• 2013

초임계조건의 기체수소/액체산소 화염의 난류유동 및 온도장에 대해 난류모델을 이용한 해석이 수행되었다. 실제유체의 연소유동을 해석하기 위하여 화염편모델에 SRK 상태방정식이 도입되었다. 수정된 압력-속도-밀도 연계알고리듬이 초임계유동에 적용되었다. 수정된 알고리듬을 토대로 6개의 대류항 차분법과 4개의 난류모델의 상대적인 성능비교가 이루어졌다. 선택된 난류모델들은 실제유체 연소유동의 다양한 특징을 고려하기 위해서 수정이 필요함을 나타내었다.