• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.5
• /
• pp.1-11
• /
• 2008

This work proposes a 15b 50MS/s CMOS pipeline ADC based on digital code-error calibration. The proposed ADC adopts a four-stage pipeline architecture to minimize power consumption and die area and employs a digital calibration technique in the front-end stage MDAC without any modification of critical analog circuits. The front-end MDAC code errors due to device mismatch are measured by un-calibrated back-end three stages and stored in memory. During normal conversion, the stored code errors are recalled for code-error calibration in the digital domain. The signal insensitive 3-D fully symmetric layout technique in three MDACs is employed to achieve a high matching accuracy and to measure the mismatch error of the front-end stage more exactly. The prototype ADC in a 0.18um CMOS process demonstrates a measured DNL and INL within 0.78LSB and 3.28LSB. The ADC, with an active die area of $4.2mm^2$, shows a maximum SNDR and SFDR of 67.2dB and 79.5dB, respectively, and a power consumption of 225mW at 2.5V and 50MS/s.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.9
• /
• pp.68-73
• /
• 2013

In this paper, we proposed a readout circuit of pulse waveform and rate for a U-health system to monitor health condition. For long-time operation without replacing or charging a battery, either pulse waveform or pulse rate is selected as the output data of the proposed readout circuit according to health condition of a user. The proposed readout circuit consists of a simple digital logic discriminator and a dual-mode ADC which operates in the ADC mode or in the count mode. Firstly, the readout circuit counts pulse rate for 4 seconds in the count mode using the dual-mode ADC. Health condition is examined after the counted pulse rate is accumulated for 1 minute in the discriminator. If the pulse rate is out of the preset normal range, the dual-mode ADC operates in the ADC mode where pulse waveform is converted into 10-bit digital data with the sampling frequency of 1 kHz. These data are stored in a buffer and transmitted by 620 kbps to an external monitor through a RF transmitter. The data transmission period of the RF transmitter depends on the operation mode. It is generally 1 minute in the normal situation or 1 ms in the emergency situation. The proposed readout circuit was designed with $0.11{\mu}m$ process technology. The chip area is $460{\times}800{\mu}m^2$. According to measurement, the power consumption is $161.8{\mu}W$ in the count mode and $507.3{\mu}W$ in the ADC mode with the operating voltage of 1 V.

• The Journal of the Acoustical Society of Korea
• /
• v.24 no.1
• /
• pp.11-20
• /
• 2005

In this paper, we deal with the research about a S/PDIF (Sony Philips Digital Interface) receiver which can operate without PLL (Phase Locked Loop) circuits. Although a S/PDIF receiver is used in most audio devices and audio processors in these days. yet there are only few domestic researches about S/PDIF. Currently used commercial DACs (Digital-to-Analog Converters) which can decode S/PDIF signals, have a PLL circuit inside them. The PLL makes it possible to extract clock information from S/PDIF digital signal and to synchronize a clock signal with input signals. But the PLL circuit makes many diffculties in designing the SOC (System On Chips) of VLSIs (Vew Large Scale Integrated Ciruits) because it is an "analog circuit". We proposed a S/PDIF receiver which doesn't have PLL circuits and only has Pure digital circuits. The key idea of the proposed S/PDIF receiver. is to use the ratio between a 16 MHz basic input clock and S/PDIF signals. After having decoded hundreds thousands S/PDIF inputs, it went to prove that a S/PDIF receiver can be designed with pure digital circuits and without any analog circuits such as PLL circuits. We have confidence that the proposed S/PDIF receiver can be used as an IP (Intellectual Property) for the SOC design of the digital circuits.

• Journal of Astronomy and Space Sciences
• /
• v.20 no.1
• /
• pp.21-28
• /
• 2003

In case that we independently obtain orbital informations about the low earth satellites of foreign countries using radar systems, we develop the orbit determination algorithm for this purpose using a SGP4 model with an analytical orbit model and the extended Kalman filter with a real-time processing method. When the state vector is Keplerian orbital elements, singularity problems happen to compute partial derivative with respect to inclination and eccentricity orbit elements. To cope with this problem, we set state vector osculating to mean equinox and true equator cartesian elements with coordinate transformation. The state transition matrix and the covariance matrix are numerically computed using a SGP4 model. Observational measurements are the type of azimuth, elevation and range, filter process to each measurement in a lump. After analyzing performance of the developed orbit determination algorithm using TOPEX/POSEIDON POE(precision 0.bit Ephemeris), its position error has about 1 km. To be similar to performance of NORAD system that has up to 3km position accuracy during 7 days need to radar system performance that have accuracy within 0.1 degree for azimuth and elevation and 50m for range.

• Proceedings of the KOR-KST Conference
• /
• 1998.10b
• /
• pp.149-149
• /
• 1998

차종구분의 필요성은 교통공학 및 계획분야에서 교통패턴을 파악할 필요가 있으며 도로의 포장설계와 같은 구조적 측면, 교통관련자료구축 등에서도 중요하다. 현재 국내에서 운영중에 있는 각종검지기 체계들은 외국에서 개발한 체계로서 여러 가지 다양한 센서를 복합구성하여 차종을 구분하는 고가의 장비들이다. 이에 대한 국내의 연구사례는 극히 드물다고 볼 수 있다. 지금까지 주를 이룬 국내 연구사례를 보면 루프검지기를 이용한 차종구분이 주를 이루고 있다. 현재 루프검지기의 대체검지기(영상검지기, 자석검지기)개발이 활발히 진행되고 있으며 본 연구에서 이용되는 검지기는 자석검지기로서 루프검지기에 비하여 설치가 간단하고 파손의 우려가 적으며 유지관리 및 보수가 손쉽고 비용면에서도 저렴하다는 것이 장점이라 하겠다. 이에 최근에 개발되어진 단일 자석검지기를 이용한 실시간 차종인식 알고리즘을 개발하고, 현장실험을 통한 현장 적용성을 검토한다. 고속도로에 설치되어 있는 자석검지기를 이용하여 자료를 수집하며 분석에 이용되는 자료는 개별차량에 대하여 자속밀도의 변화를 주파수값으로 변환한 Digital Data값이다. 그 수치를 토대로 각 차량의 점유시간을 파악하여 각 차량의 점유시간동안 파형의 특징을 추출하여 각 특징들을 기초로 하여 각 차량이 나타내는 고유의 파형을 식별하는 패턴인식 방법으로 접근한다. 본 연구에서는 검지기 매설장소의 유한성 및 연구대상 도로의 특성으로 인하여 다양한 차종의 자료수집이 용이하지 못하여 시험가능한 자료수가 많은 차종을 대상으로 분석한다. 차종인식 알고리즘상의 차종분류는 건설교통부 차종분류기준에 따라 우선 구분이 확실한 차종으로 나눈후 단계적으로 세부적 차종분류로 접근한다.의 영향들을 고려함으로써 가로망 설계 과정에서 가로망의 상반된 역할인 이동성과 접근성의 비교가 가능한 보다 현실적인 가로망 설계 모형을 구축하고자 한다. 지금까지 소개된 가로망 설계모형들은 용량변화에 대한 설계변수의 형태에 따라 이산적 가로망 설계 모형과 연속적 가로망 설계모형으로 나뉘어지게 된다. 본 논문의 경우, 계산속도의 향상 측면에서는 연속적 가로망 설계 모형을 도입할 수 있지만, 이때 요구되는 도로용량이 이산적인 변수(차선 수)로 결정되어야만 신호제어 변수를 결정할 수 있기 때문에, 이산적 가로망 설계 모형이 사용된다. 하지만, 이산적 설계모형의 경우 조합최적화 문제이므로 정확한 최적해를 구하기 위해서는 상당한 시간이 소요되며, 경우에 따라서는 국부 최적해에 빠지게 된다. 이러한 문제를 극복하기 위해, 우선 이상적 모형의 근사화, 혹은 조합최적화문제를 위해 개발된 Simulated Annealing기법의 적용, 연속적 모형의 변수를 이산화하는 방법 등 다양한 모형들을 고려해 본 뒤, 적절한 모형을 적용할 것이다. 가로망 설계 모형에서 신호제어를 고려하기 위해서는 주어진 가로망에 대한 통행 배정과정에서 고려되는 통행시간을 링크통행시간과 교차로 지체시간을 동시에 고려해야 하는데, 이러한 문제의 해결을 위해서 최근 활발히 논의되고 있는 교차로에서의 신호제어에 대응하는 통행배정 모형을 도입하여 고려하고자 한다. 이를 위해서 지금까지 연구되어온 Global Solution Approach와 Iterative Approach를 비교, 검토한 뒤 모형에 보다 알맞은 방법을 선택한다. 차량의 교차로 통행을 고려하는 performance function의 경우 비신호 교차로와 신호교차로에 대

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.161-162
• /
• 2011

최근 광전자 분야에서는 미래 에너지 자원에 대한 관심과 함께 GaN 기반 태양전지 연구가 활발히 진행되고 있다. GaN 물질은 높은 전자 이동도와 높은 포화 속도 등 광전자 소자에 유리한 광, 전기적 특성들을 가지고 있다. 또한, In의 함량을 변화시켜가며, 0.7eV에서 3.4eV까지 밴드갭을 조절함으로써, 자외선부터 적외선까지 태양빛 스펙트럼의 대부분을 흡수할 수 있는 장점이 있다. InGaN 태양전지의 효율을 높이기 위해서는 In의 함량을 늘려 밴드갭을 줄이는 것이 중요하다. 하지만 GaN 와 InN 간의 격자 부정합으로 인해 In 함량이 높은 단결정 InGaN 층을 두껍게 성장 하는 것이 어렵다. 때문에 GaN 기반 태양전지 관련 연구 그룹들이 태양전지의 효율 향상을 위해 활성층에 양자우물(MQWs) 구조, Supper Lattice (SLs) 구조와 같이 얇은 InGaN/GaN 층을 주기적으로 반복하여 적층함으로써 높은 조성의 In을 함유한 상질의 InGaN/GaN 층을 성장하는 연구들을 진행해 왔다. 본 연구에서는, p-i-n 구조와 MQW 구조를 갖는 InGaN 기반 태양전지를 제작하여, 각각의 특성을 분석해 봄으로써, In0.1Ga0.9N 태양전지 활성층의 구조에 따른 장/단점에 대해 논의하였다. 먼저 MOCVD를 이용하여 200 nm의 i-In0.1Ga0.9N 활성층을 갖는 p-i-n 구조와 In0.19Ga0.81N/GaN(3 nm/8 nm) MQWs (8 periods) 구조를 갖는 태양전지 에피를 각각 성장하였고, 그 후 공정을 통해 그림 1과 같이 InGaN 태양전지 소자를 제작하였다. 그 후, 각 태양전지의 전류/전압 곡선과 외부양자효율을 측정하여 그림 2와 같은 결과를 얻었다. p-i-n과 MQW 샘플의 외부양자효율은 각각 ~70%, ~25%로 측정 되었다. MQW 샘플의 외부 양자효율이 높지 않음에도 불구하고 p-i-n 구조에 비해 높은 In 함량을 가지고 있으므로, 더 넓은 파장의 빛을 흡수하여, 높은 단락전류(0.778 mA/cm2)를 보이고 있다. 또한 p-i-n 구조에 비해 높은 개방전압(2.3V)를 가지고 있으므로, MQW 샘플이 약 17% 정도 높은 변환효율(1.4%)를 보이고 있다. 이후 추가적으로 p-i-n 과 MQW 구조의 InGaN 태양전지에 나타나는 Voc와 Jsc의 차이를 Polarization 효과를 비롯한 다양한 측면에서 분석해 보고자 한다.

• Applied Chemistry for Engineering
• /
• v.24 no.1
• /
• pp.31-37
• /
• 2013

Lowering surface reflectance of Si wafers by texturization is one of the most important processes for improving the efficiency of Si solar cells. This paper presents the results on the effect of texturing using acidic solution mixtures containing the catalytic agents to moderate etching rates on the surface morphology of mc-Si wafer as well as on the performance parameters of solar cell. It was found that the treatment of contaminated crystalline silicon wafer with $HNO_3-H_2O_2-H_2O$ solution before the texturing helps the removal of organic contaminants due to its oxidizing properties and thereby allows the formation of nucleation centers for texturing. This treatment combined with the use of a catalytic agent such as phosphoric acid improved the effects of the texturing effects. This reduced the reflectance of the surface, thereby increased the short circuit current and the conversion efficiency of the solar cell. Employing this technique, we were able to fabricate mc-Si solar cell of 16.4% conversion efficiency with anti-reflective (AR) coating of silicon nitride film using plasma-enhanced chemical vapor deposition (PECVD) and Si wafers can be texturized in a short time.

• Journal of KIISE:Software and Applications
• /
• v.34 no.1
• /
• pp.1-10
• /
• 2007

This paper proposes a new indexing mechanism for MPEG-7 visual descriptors, especially Dominant Color and Contour Shape descriptors, that guarantees an efficient similarity search for the multimedia database whose visual meta-data are represented with MPEG-7. Since the similarity metric used in the Dominant Color descriptor is based on Gaussian mixture model, the descriptor itself could be transform into a color histogram in which the distribution of the color values follows the Gauss distribution. Then, the transformed Dominant Color descriptor (i.e., the color histogram) is indexed in the proposed indexing mechanism. For the indexing of Contour Shape descriptor, we have used a two-pass algorithm. That is, in the first pass, since the similarity of two shapes could be roughly measured with the global parameters such as eccentricity and circularity used in Contour shape descriptor, the dissimilar image objects could be excluded with these global parameters first. Then, the similarities between the query and remaining image objects are measured with the peak parameters of Contour Shape descriptor. This two-pass approach helps to reduce the computational resources to measure the similarity of image objects using Contour Shape descriptor. This paper also proposes two integration schemes of visual descriptors for an efficient retrieval of multimedia database. The one is to use the weight of descriptor as a yardstick to determine the number of selected similar image objects with respect to that descriptor, and the other is to use the weight as the degree of importance of the descriptor in the global similarity measurement. Experimental results show that the proposed indexing and integration schemes produce a remarkable speed-up comparing to the exact similarity search, although there are some losses in the accuracy because of the approximated computation in indexing. The proposed schemes could be used to build a multimedia database represented in MPEG-7 that guarantees an efficient retrieval.

• Journal of the Korean Geotechnical Society
• /
• v.31 no.6
• /
• pp.27-44
• /
• 2015

An analytical solution of dynamic responses for seabed in finite and infinite thicknesses including shallow has been developed under flow and partial standing wave with arbitrary reflection ration coexisting field at a constant water depth condition. In the analytical solution, a field was simply transited to a coexisting field of progressive wave and flow when reflection ratio was 0 and to a coexisting field of fully standing wave and flow when reflection ratio was 1. Based on the Biot's consolidation theory, the seabed was assumed as a porous elastic media with the assumptions that pore fluid is compressible and Darcy law governs the flow. The developed analytical solution was compared with the existing results and was verified. Using the analytical solution the deformation, pore pressure, effective and shear stresses were examined under various given values of reflection ratio, flow velocity, incident wave's period and seabed thickness. From this study, it was confirmed that the dynamic response of seabed was quite different depending on consideration of flow, which causes changing period and length of incident and reflection waves. It was also confirmed that dynamic response significantly depends on the magnitude of reflection ratio.

• Journal of the Institute of Convergence Signal Processing
• /
• v.19 no.2
• /
• pp.61-67
• /
• 2018

Welding preheating means that the surface of the base material to which the metal is welded before the main welding is heated to a constant temperature. It prevents the cracks of the adjacent influences such as reduction of material hardening degree by controlling the cooling rate, suppression of segregation of impurities, prevention of thermal deformation, and moisture removal. For this reason, it is a necessary operation for high quality welding. Induction heating is an efficient heating method that converts electric energy into heat energy by applying electromagnetic induction phenomenon. Compared with combustion heat generated by gas and liquid, it is clean, stable, and economical as well as rapid heating. It can be heated regardless of the shape, depth and material of the heating body by modifying the shape of the frequency and the coil with a simple structure. In this paper, we implemented a low frequency welding preheating system using induction heating technique and observed the temperature changes of coil resistance, inductance and automotive transmission parts according to the height of each transmission in winding coil for three kinds of automotive transmission parts. We confirmed that the change of current is a very important factor in the low frequency heating.