• Korean Journal of Food Science and Technology
• /
• v.15 no.3
• /
• pp.282-286
• /
• 1983

In order to obtain practical information for efficient energy usage in sterilization, energy consumption was monitored for various processing variables, i.e. heat transfer type (conduction and convection), can size (No. 202-2, No. 301-3, No. 301-7, and No. 603-2), retorting temperature $(110^{\circ}C-121^{\circ}C\;and\;130^{\circ}C)$, and sterilization method (steam, and hot water sterilization). Less energy was consumed for smaller can size and higher temperature, and this trend was more distinguished in conductive food than convective food. Hot water sterilization could lower energy consumption in conductive food, but not in convective food. Energy consumption data of this work was reasonable when compared with energy consumption of sterilization in canneries, and therefore thought to be able to be used for estimation, design and optimization of energy consumption in sterilization.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.7
• /
• pp.1354-1362
• /
• 2015

Heterogeneous network technology is expected to be a core technology for 5G mobile communications. 5G mobile network would be composed of many base stations even have mobility, then the operator should connect base stations through the wireless backhaul technology. This paper presents Ultra Wide Area Wireless Backhaul Network System with massive array antenna. We conducted link budget analysis for Ultra Wide Area Wireless Backhaul Network and performance analysis of massive array antenna system through the transmission simulator based on beamforming technology. In wide area ($10km^2$) wireless backhaul system composed of massive antenna, we achieved 5 bps/Hz average spectral efficiency with 1 W transmission power per beam.

• Korean Journal of Optics and Photonics
• /
• v.15 no.5
• /
• pp.423-428
• /
• 2004

The development of a compact and high performance MWIR thermal imaging sensor based on the SOFRADIR 320${\times}$240 element IRCCD detector is described. The sensor has 20 magnification zoom optics with the maximum 40$^{\circ}$${\times}$30$^{\circ}$ of super wide field of view and 7.6 cycles/mrad of resolving power with the operation of attached micro-scanning system. In order to correct nonuniformities of detector arrays, we have proposed a multi-point correction method using defocusing of the optics and we have acquired the highest quality images. The MRTD of our system shows good results below 0.05K at spatial frequency 1 cycles/mrad at narrow field of view. Experimental data and obtained performances are presented and discussed.

• Korean Journal of Ichthyology
• /
• v.12 no.2
• /
• pp.146-153
• /
• 2000

The development of larvae and juvenile of the smoothskin sculpin (Ocynectes modestus) caught at Pusan brook in May and June 1995 was described. Yolk was completely absorbed when the larvae was about 6.28 mm in average standard length (ASL) with 32~33 myomeres. Flexion of the notochord started when the juvenile was about 7.36 mm in ASL and finished about 9.34 mm in ASL, respectively. Aggregate numbers of all fin rays were completed at over 10.08 mm in ASL, when the larvae reached the juvenile stage. One pairs of flaps were observed on the dorsal surface of the head at 10.08 mm in ASL. The juveniles longer then 14.00 mm in ASL has the same pigment pattern as that of adults. A new Korean name "Min-Ga-Si-Ggeog-Jeong-i" is proposed for this species.

• Composites Research
• /
• v.28 no.4
• /
• pp.226-231
• /
• 2015

Various characteristics(thermal expansion, microstructure, etc.) and mechanical properties of CNT-aluminum nano composites manufactured by volume production system were evaluated. Also, formability and durability were evaluated for potential applications in automotive parts, via compared with high-elasticity material (A390) and the current commercial product. As a result, this composite has excellent mechanical properties and formability, therefore, to verity its potential for application as light and high strength materials in automobile part.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.4 s.107
• /
• pp.351-357
• /
• 2006

In this paper, a direct $TM_{01}-TE_{11}$ mode converter of circular waveguide which is used the approximated design method of mode conversion between $TM_{01}$ and $TE_{11}$ modes is designed for radiation with the maximum directivity of high power energy into air (rom high power microwave antenna system. The proposed direct $TM_{01}-TE_{11}$ mode converter is calculated and designed with an approximated method for non-linear function about an extended non-constant serpentine type of circular waveguide. Then, the designed mode converter is optimized by length of 200 mm and efficiency above 95% by FIM simulation and achieved short length and high efficiency of the antenna by results of fabricated and measured characteristics.

• Journal of IKEEE
• /
• v.5 no.1 s.8
• /
• pp.16-23
• /
• 2001

Passive noise reduction is a classical approach to attenuate industrial noise, and an active noise cancellation has several advantages over the passive noise cancellation. The active noise reduction system offers a better low frequency performance with a smaller and lighter system. This paper presents a simple active closed loop control system which consists of an controller for inverting and compensating the phase delay, a microphone for picking up the external noise, and a loudspeaker for radiating the acoustic out of phase signal to reduce the external noise, and external noise can be reduced after compensating the phase difference to be $180^{\circ}$ in the frequency of maximum value in the amplitude response. The noise of the phase delay covered from $50^{\circ}\;to\;310^{\circ}$ tends to be reduced in the active noise control system and it is possible to obtain a noise cancelling of up to approximately 20[dB] at the ears in the enclosurer.

• Journal of IKEEE
• /
• v.24 no.1
• /
• pp.19-24
• /
• 2020

This paper presents a 3-level, 2-level SVPWM technique with 100 kHz switching using Verilog HDL, one of the languages of FPGA. In the case of IGBT devices mainly used in inverters, they have a switching frequency around 20kHz. Recent research and development of next-generation power semiconductor devices such as GAN has enabled switching of more than 100kHz, which can miniaturize power converters, and apply various new algorithms due to the injection of harmonics. In the existing system using the IGBT, the control using the DSP is common, but the controller configuration for 100 kHz switching requires the use of FPGA. Therefore, this paper explains the theory and implementation of SVPWM applied to two-level and three-level inverters using FPGAs and verifies the performance through the output waveform. In addition, this paper implements 3-level SVPWM by using only one carrier instead of using two carriers in the conventional method.

• Journal of the Korean Institute of Gas
• /
• v.17 no.3
• /
• pp.20-26
• /
• 2013

In this research, an empirical study on the designed burst pressure of Type3 composite cylinder was performed by hydrostatic burst test equipment. The designed burst pressure of Type3 composite cylinders, which are 6.8 liter and 31 MPa of service pressure, was estimated with the analysis using the finite element method. In order to confirm its accuracy, the burst test of small Type3 composite cylinders was perfomed through three times. The burst test equipment can pressurize to 400 MPa. As a result of comparison between the designed burst pressure and actual burst pressure, the difference was less than 4 percentage. With a test result, the analysis accuracy was verified. This technique will be applied to both qualification and inspection for the composite cylinder.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.10
• /
• pp.1033-1040
• /
• 2011

The premixed burner is a very strong candidate for using household boiler burner system because it has high efficiency, low emission and can be used in compact boiler system. Usually, household boiler burner systems use a Bunsen burner, which consists of an inner rich premixed flame and fuel burned completely by a secondary air supply. It has a relatively long flame length and operates in a high excess of air, so it is difficult to fit such a burner into a high efficiency compact boiler. In this paper, the characteristics of a premixed combustion burner for surface media such as metal fiber, ceramic, and SUS fin were evaluated. In particular, the flow velocity over the burner surface for the cold flow characteristics of the surface material were measured and adjusted. The combustion tests were carried out by taking pictures of the flame and measuring the flame temperature. The amounts of CO and NO were measured and the characteristics of the surface burner materials, combustion chamber, and heat exchangers were evaluated for various excess air ratios and heating values.