• Journal of the Institute of Convergence Signal Processing
• /
• v.9 no.2
• /
• pp.141-145
• /
• 2008

When the current flows to parallel lines with different length, it is researched that the radiation is occured by the common-mode current radiates, and the small light weight antenna composed of dual elements by using the principle is proposed. However, there is a problem in production about this antenna because this liner antenna is structured by combining with wires. In this paper, we improved this liner antenna, and designed the plane antenna composed of dual elements with different length in the plane printed board to produce and to design easily. Furthermore, the antenna with the wide-band characteristic is also designed in the same board. The radiation pattern is similar to the dipole antenna on account of designing the triangular patch S, the notch and two tapers in patch S, the notch and two tapers in the antenna element. In result, it was able to design the antenna working wider band-width(the bandwidth ratio about 58%, $VSWR{\le}2$).

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.1
• /
• pp.55-60
• /
• 2002

For the development of a new creep test technique, the availability of SP-Creep test is discussed for 1Cr-0.5Mo boiler header material. And some results are also compared with those of 2.25Cr- 1Mo steel which widely uses as boiler superheater tube. The results can be summarized as follows. The load exponents(n) obtained by SP-Creep test for 1Cr-0.5Mo steel are decreased with increasing creep temperature and the values are 15.67, 13.89, and 17.13 at 550$^{circ}C$ ,575$^{circ}C$ and 600$^{circ}C$, respectively. The temperature dependence of the load exponent is given by n = 107.19 - 0.1108T. This reason that load exponents show the extensive range of 10∼16 is attributed to the fine carbide such as M$_{23}$C$_{6}$ in lath tempered martensitic structures. At the same creep condition, the secondary creep rate of 1Cr-0.5Mo steel is lower than the 2.25Cr-1Mo steel1 due to the strengthening microstructure composed by normalizing and tempering treatments. Through a SEM observation, it can be summarized that the primary, secondary, and tertiary creep regions of SP-Creep specimen are corresponding to plastic bending, plastic membrane stretching, and plastic instability regions among the deformation behavior of four steps in SP test, respectively.y.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.11
• /
• pp.951-956
• /
• 2008

The high temperature creep properties of the generating plant's high temperature tube, pipe and header and such are very significant in accordance with long-time exposure to the high temperature and pressure environment. Not only this, but as the welding procedure is compulsory for the cohesion of components, the creep properties regarding the local microstructures of steel weldment are very important. In order to understand the creep properties regarding the local microstructures of steel weldment, the SP-Creep test which is easy to get sample from the field component was conducted. The local microstructure of steel weldment, that is, W.M. and B.M.'s microstructures were observed using the SEM. The rupture time of W.M. was longer as 110 % averagely in a same condition, which is the consequence of the difference of the microstructure. Each lethargy coefficient of B.M. and W.M. is evaluated by the relation among the temperature, load and the rupture time from SP-Creep Test. The life estimation equation can be induced by the transformation of Power-law. B.M. and W.M. for each $550\;^{\circ}C$ and $575\;^{\circ}C$, the very similar to normal temperature of the domestic thermal power generation in working, are estimated.

• Journal of Internet Computing and Services
• /
• v.9 no.6
• /
• pp.117-125
• /
• 2008

With increase of concern about the Ubiquitous application, the necessity of the computer system which is miniaturized is becoming larger. The ARM processor is showing a high share from embedded system market. In this paper, ideal method for RTD-1000 controller construction and development is described using ARM microcontroller. Existing RTD-1000 measures distance of disconnection or defect of sensing casket by measuring receiving reflected wave which was sent via copper wire inside the leaking sensing rod. Using this RTD-1000, leakage and breakage of water and oil pipe can be sensed and it reports damage results to the networks. But, existing RTD-1000 wastes hardware resources much and costs a great deal to installation. Also, it needs a cooling device because the heating problem, and has some problem of the secondary memory unit such as the hard disk. So, long tenn maintenance has some problems in the outside install place. In this paper, for the resolving the problem of RTD-1000, RTD-1000A embedded system based on ARM is proposed and simulated.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.2
• /
• pp.157-164
• /
• 2012

The design strategy of the multi-functional structure is that the electrical components and the circuits are directly put on their supporting structural panel in which the radiation shields and the thermal control functions are integrated. Applying the multi-functional structure reduces the total mass and size of the space system and makes it possible to lower launch cost. In present study the performance of thermal radiation for six types of multi-functional structure are investigated by the numerical method. The effect of the rib configuration on heat transfer for the multi-functional-structure is not important alone but is meaningful considering with the structural stiffness, difficulty of manufacturing and mass increase. In heat spreading point of view, the thickness of the outer conductive layer is important rather than the rib configuration and the trade-off study with the mass and thickness is required for optimum design.

• Journal of Korean Society of Rural Planning
• /
• v.24 no.3
• /
• pp.33-42
• /
• 2018

The aim of our study was to provide a basic data for the development of a small greenhouse model suitable for urban farmers. The study analyzed installation inclination, positive and negative reasons for installation, location of installation, preferred crops in small greenhouses, plans for use of products, and expected effects by using small greenhouse. Positive opinion on small greenhouse installation was 80.4% of the survey respondents. The most positive reason for the installation of small greenhouses was fresh and safe food supply, and the negative reason was maintenance difficulties. The results obtained in our survey indicated that small greenhouses were more likely to be installed near the house, and urban farmers tended to grow organic leafy vegetables in soil. The expected benefits of small greenhouse operation were largely divided into 'benefit for the improvement of the quality of life' and 'benefit for economic profits', and expectation for the improvement of the quality of life was higher than economic benefit. As a result of the Likert 5-point scale analysis, 'benefit for the improvement of the quality of life' by using a small greenhouse was graded as high as 4.17~4.60. On the other hand, the 'benefit to economic profits' was rated as low as 3.51~4.14.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.19 no.6
• /
• pp.411-419
• /
• 1999

It has been well recognized that a long term service at elevated temperature of $350^{\circ}C{\sim}550^{\circ}C$ induces embrittlement damage due to carbide precipitation and/or P, Sb and Sn segregation at grain boundaries and thereby deteriorates the grain boundary strength of heat resisting components in the energy-related plants. Therefore, it is very important to assess quantitatively the extent of embrittlement damage of heat resisting components to secure the reliable and efficient service condition and to prevent brittle failure in service. However, because fracture tests are limited in size and number of specimen obtained from the structural components, nondestructive test method is required. In this study, the optimum electrochemical parameters are investigated and discussed to evaluate nondestructive embrittlement damage for aged 2.25Cr-1Mo steels by means of electrochemical polarization test method (ECPTM) in proper corrosive environment. In addition, the electrochemical test results are compared with embrittlement degree evaluated by semi-nondestructive SP test.

• Journal of Navigation and Port Research
• /
• v.30 no.8 s.114
• /
• pp.617-622
• /
• 2006

Gamcheon Harbor was developed to cope with increased freight demand of Busan port and supplement function of the north port. Because container wharf is opened to 1997 as well as general wharf, present maximum 50,000DWT class containerships have been incoming and outgoing. However, In Gamcheon port, small size ships such as fishing boats, miscellaneous boats account for 50 percent of the traffic and a public marine products wholesale market that is building on the north wharf will open in 2008. Therefore, it needs to grasp future year traffic volume before establishing operation plan for port management. Also, analysis on crossing situation risk is required because the breakwater entrance in Gamcheon Harbor is narrow and the crossed passing of ship is ever-present at breakwater front. Thus the traffic volume in the future was presumed and quantitative analysis was achieved on crossing situation though simulations with the traffic volume.

• Korean Journal of Food Science and Technology
• /
• v.15 no.3
• /
• pp.282-286
• /
• 1983

In order to obtain practical information for efficient energy usage in sterilization, energy consumption was monitored for various processing variables, i.e. heat transfer type (conduction and convection), can size (No. 202-2, No. 301-3, No. 301-7, and No. 603-2), retorting temperature $(110^{\circ}C-121^{\circ}C\;and\;130^{\circ}C)$, and sterilization method (steam, and hot water sterilization). Less energy was consumed for smaller can size and higher temperature, and this trend was more distinguished in conductive food than convective food. Hot water sterilization could lower energy consumption in conductive food, but not in convective food. Energy consumption data of this work was reasonable when compared with energy consumption of sterilization in canneries, and therefore thought to be able to be used for estimation, design and optimization of energy consumption in sterilization.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.2 s.117
• /
• pp.118-125
• /
• 2007

Harmonic band of bandpass filter(BPF) is suppressed using coupled mushroom structure. Between double positive (DPS) transmission line such as microstrip and double negative(DNG) transmission line such as one dimensional mushroom structure, strong coupling broadly arises in the cross range of dispersion curves of isolated microstrip and mushroom structure because of complex propagation constant in the cross range. Strong coupling inhibits wave propagation, so that this kind of structure can be utilized as bandstop filter(BSF). This BSF utilizes coupled transmission line instead of coupled resonator, resulting in broad bandwidth(>30 %), shan-rejection, and high rejection level. The strong coupling between DPS and DNG transmissionline makes it possible shorten coupling length, resulting in compact size. In this paper, parallel coupled BSF having center frequency of 4 GHz and 3 dB fractional bandwidth of 40 % is designed and utilized to suppressed spurious mode of two bandpass filters.