• Fire Science and Engineering
• /
• v.33 no.4
• /
• pp.35-40
• /
• 2019

In this study, the mass flow rate of the heat release rate equation, which is the major factor of the oxygen consumption method, was analyzed for the fundamental investigation of the cone-calorimeter (5 m length and 0.3 m diameter). The shapes of a completely empty inside, 3 mm pore diameter mesh and pore diameter 10 mm honeycomb with 0.76 porosity were constructed using the cone-calorimeter. To calculate the mass flow rate, four bi-directional probes and thermocouples were installed in a uniform position in the vertical direction of flow. The velocity gradient and flow perturbation were measured from the increase in Reynolds number. As the flow capacity increased, the speed gradient increased in all three shapes relative to the turbulence intensity. In addition, the deviation of extended uncertainty to the mass flow was completely low in the order of empty space, mesh (d_p = 3 mm) and honeycomb (d_p = 10 mm and 𝜖 = 0.76) at the 95% confidence level. The results can be used in designs to improve the flow stability of the cone calorimeter.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.36 no.2
• /
• pp.201-208
• /
• 2007

Functional oils (FOs) were produced from commercial diacylglycerol oil and red yeast rice extracts from 80% ethanol for 1 hr in a shaking water bath at $35^{\circ}C$ and 175 rpm. FOs contained (A) 600, (B) 1200, (C) 1800, and (D) 2280 ppm of red yeast-rice extracts, respectively. The Hunter a value and b value were risen whereas L value was reduced along with the increase of extract concentration. Content of monacolin K and total phenolic compounds in FOs significantly increased according to the increase of extract concentration. The oxidation stability of FOs was observed by Rancimat at $98^{\circ}C$. Induction time decreased according to the increase of extract concentration. The major volatile compounds of FOs were compared using the electronic nose (EN) system and solid phase microextraction (SPME) method combined with gas chromatograph/mass spectrometry (GC/MS). EN was composed of 12 different metal oxide sensors. Sensitivities (Rgas/Rair) of sensors from EN were analyzed by principal component analysis (PCA), whose proportion was 99.66%. For qualitative or quantitative analysis of volatile compounds by SPME-GC/MS, the divinylbenzene/carboxene/polydimethyl-siloxane fiber and sampling temperature of $50^{\circ}C$ were applied.

• Journal of Korean Society of Forest Science
• /
• v.76 no.1
• /
• pp.41-50
• /
• 1987

The various conditions of photographs, especially kinds of films, combinated filters and seasons are important factors for forestry purpose aerial photography. In this paper the variations of tones were compared between color and color infrared, panchromatic black and white and infrared black and white, and among false color photographic images created by using 3 kinds of filters when prints are made. Color infrared film was good for identifying tree species, for its spectral signatures had a greater range of tones and hues than color signatures. In that case taken in May were more effective than taken April. False color photographs were not so good as color photographs because they were mostly dark and indistinct. Infrared black and white film with medium red filter showed potential for separating broad-leaved forests from conifers. MSS composed photographs, when composed with proper bands and densities, were proved useful for distinguishing land use types but not applicable to more detailed practices such as forest type separation and tree species identification.

• Journal of Convergence for Information Technology
• /
• v.10 no.7
• /
• pp.33-40
• /
• 2020

This work tackles the problem of conventional reinforcement learning scheme which has a relatively long training time to reduce energy consumption in underwater network. The enhanced scheme adjusts the learning range of reinforcement learning based on distance estimation. It can be reduce the scope of learning. To take account the fact that the distance estimation may not be accurate due to the underwater wireless network characteristics. this research added noise in consideration of the underwater environment. In simulation result, the proposed AQ-NAV scheme has completed learning much faster than existing method. AQ-NAV can finish the training process within less than 40 episodes. But the existing method requires more than 120 episodes. The result show that learning is possible with fewer attempts than the previous one. If AQ-NAV will be applied in Underwater Networks, It will affect energy efficiency. and It will be expected to relieved existing problem and increase network efficiency.

• Journal of Adhesion and Interface
• /
• v.9 no.3
• /
• pp.20-26
• /
• 2008

It is well know that the structure of shape memory alloy (SMA) can change from martensite austenite by either temperature or stress. Due to their inherent shape recovery properties, SMA fiber can be used such as for stress or cure-monitoring sensor or actuator, during applied stress or temperature. Incomplete superelasticity was observed as the stress hysteresis at stress-strain curve under cyclic loading test and temperature change. Superelasticity behavior was observed for the single-SMA fiber/epoxy composites under cyclic mechanical loading at stress-strain curve. SMA fiber or epoxy embedded SMA fiber composite exhibited the decreased interfacial properties due to the cyclic loading and thus reduced shape memory performance. Rigid epoxy and the changed interfacial adhesion between SMA fiber and epoxy by the surface treatment on SMA fiber exhibited similar incomplete superelastic trend. Epoxy embedded single SMA fiber exhibited the incomplete recovery during cure process by remaining residual heat and thus occurring residual stress in single SMA fiber/epoxy composite.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.15 no.1
• /
• pp.197-210
• /
• 2012

The KOrea Multi-Purpose SATellite(KOMPSAT)-2 has a capability to provide a cross-track stereo imagery using two different orbits for generating various spatial information. However, in order to fully realize the potential of the KOMPSAT-2 stereo imagery in terms of mapping, various tests are necessary. The purpose of this study is to evaluate the possibility of mapping using the KOMPSAT-2 stereo imagery. For this, digital plotting was conducted based on the stereoscopic images. Also the Digital Elevation Model(DEM) and an ortho-image were generated using digital plotting results. An accuracy of digital plotting, DEM, and ortho-image were evaluated by comparing with the existing data. Consequently, we found that horizontal and vertical error of the modeling results based on the Rational Polynomial Coefficient(RPC) was less than 1.5 meters compared with the Global Positioning System(GPS) survey results. The maximum difference of vertical direction between the plotted results in this study and the existing digital map on the scale of 1/5,000 was more than 5 meters according as the topographical characteristics. Although there were some irregular parallax on the images, we realized that it was possible to interpret and plot at least seventy percent of the layer which was required the digital map on the scale of 1/5,000. Also an accuracy of DEM, which was generated based on the digital plotting, was compared with the existing LiDAR DEM. We found that the ortho-images, which were generated using the extracted DEM in this study, sufficiently satisfied with the requirement of the geometric accuracy for an ortho-image map on the scale of 1/5,000.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.49 no.6
• /
• pp.18-24
• /
• 2012

This paper reports the test results of a 50MHz/s 10 bits DAC developed with $0.18{\mu}m$ CMOS process for the wireless sensor network application. The 10bits DAC, not likely a typical segmented type, has been designed as a current driving type with double step thermometer decoding architecture in which 10bits are divided into 6bits of MSB and 4bits of LSB. MSB 6bits are converted into 3 bits row thermal codes and 3 bits column thermal codes to control high current cells, and LSB 4 bits are also converted into thermal codes to control the lower current cells. The high and the lower current cells use the same cell size while a bias circuit has been designed to make the amount of lower unit current become 1/16 of high unit current. All thermal codes are synchronized with output latches to prevent glitches on the output signals. The test results show that the DAC consumes 4.3mA DC current with 3.3V DC supply for 2.2Vpp output at 50MHz clock. The linearity characteristics of DAC are the maximum SFDR of 62.02dB, maximum DNL of 0.37 LSB, and maximum INL of 0.67 LSB.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.5
• /
• pp.183-190
• /
• 2013

In this paper, we propose an improved anisotropic diffusion model for micro-crack detection in heterogeneously textured surface of polycrystalline solar wafers. Due to the nature of the image sensor, the gray-level of the diagonal micro-crack is non-uniform. Thus, the conventional algorithms can't fully detect diagonal micro-cracks when the number of iteration is not enough. However, the increasing of the iteration number leads to increase computation time and detects micro-crack thicker than the original micro-crack. In order to overcome this drawback, we use the gradient of north, south, east, and west directions as well as extended directions. To calculate the diffusion coefficients, we compare the gradients of conventional directions and extended directions and apply the larger gradient values to the coefficient function. This is because the proposed method reflects the information of diagonal micro-crack. Comparing to Tsai et al.'s and Ko and Rheem's, the proposed algorithm shows superior efficiency in detecting the diagonal micro-cracks with less iterations in the images of polycrystalline solar wafers. In addition, it also shows that the thickness of segmented micro-crack is similar to the orignal micro-crack.

• Journal of the Korean Society for Railway
• /
• v.18 no.5
• /
• pp.401-409
• /
• 2015

Defects generated in a railroad track that guides the railroad vehicle have the characteristic of growing fast; as such, the detection technology for railroad track defects is very important because defects can eventually cause mass disasters like derailments. In this study, a speed-up test facility was fabricated to investigate the feasibility of using magnetic flux leakage (MFL) technology for defect detection in a railroad track under speed-up condition; a test was conducted using a railroad track specimen with defects. For this purpose, an MFL sensor head dedicated to the configuration of the railroad was designed and test specimens with artificial defects on their surfaces were manufactured. Using the test facility, a speed-up test ranging from 4km/h to 12km/h was performed and defects including locations were successfully detected from MFL signals induced by defects with enhanced visibility by differentiating raw MFL signals. In the future, it should be possible to apply this system to a high-speed railroad inspection car by improving the lift-off stability that is necessary for speed-up of the developed MFL sensor system.

• Journal of IKEEE
• /
• v.21 no.4
• /
• pp.368-374
• /
• 2017

In this Paper, we developed a low power type LED security light using LED lighting that substitutes a 220[V] commercial power source for a solar cell module instead of a halogen or a sodium lamp. in addition, a PWM type drive control circuit is designed to minimize the heat generation problem and the drive current of the LED drive controller. in developed system, The light efficiency measurement value is 93.6[lm/W], and a high precision temperature sensor is used inside the controller to control the heat generation of the LED lamp. In order to eliminate the high heat generated from the LED lamp, it is designed to disperse quickly into the atmosphere through the metal insertion type heat sink. The heat control range of LED lighting was $50-55[^{\circ}C]$. The luminous flux and the lighting speed of the LED security lamp were 0.5[s], and the beam diffusion angle of the LED lamp was about $110[^{\circ}C]$ by the light distribution curve based on the height of 6[m].