• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.32B no.11
• /
• pp.1464-1472
• /
• 1995

In this paper, we propose an error diffusion image halftoning technique based on the noise spectrum shaping. The new technique can arbitrarily control the shape of the display error spectrum whereas conventional halftoning algorithms have been known to minimize dc errors only in which case edge information cannot be properly rendered. As a method for estimating the error diffusion coefficients, a least mean square (LMS) approach is adopted.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2004.05b
• /
• pp.777-783
• /
• 2004

하천 세내지 주변은 급속한 시가지 조성과 인구밀집으로 유역의 불투수층이 증가하여 홍수도달시간이 짧아지고 홍수유출량이 증가하고 있다. 또한 엘리뇨${\cdot}$라니냐 등의 이상기후로 홍수사상의 발생 빈도와 규모가 증가하면서 홍수피해도 대형화되어 가고 있다. 그러나 치수사업은 다른 공공사업에 비해 경제성이 저평가 되어 투자우선순위가 밀려 사업시행이 지연되고 예방적 차원의 대책도 미흡하여 피해가 증가하는 악순환이 계속되고 있다. 따라서 본 인구에서는 우리나라의 치수경제성 분석에 있어 계량화하지 못하고 있는 자산이용고도화 효과를 치수안전도와 더불어 분석하고자 한다. 자산이용고도화는 치수사업 시행으로 해당지역의 치수안전도 향상에 따른 자산가치의 상승을 말하는데, 특정지역의 자산가치를 가장 객관적으로 표현할 수 있는 공시지가를 근거로 분석을 수행하였다. 치수사업 시행으로 인한 편익과 하천 특성에 따른 지가변동률의 차이가 통계적으로 유의성이 있는지를 분산분석을 통해 검증하였으면, 자산가치의 상승을 순수 연평균지가변동률로 나타내었다. 치수안전도는 홍수피해 잠재성과 홍수방어능력으로 구분하였는데 홍수피해 잠재성은 도시화율에 따라 구분하였고, 홍수방어능력은 홍수량의 빈도해석과 불확실성을 고려하여 조건부 비초과확률로 나타내었다. 본 연구에서는 소도시 지역(경안천, 복하천, 청미천)을 대상으로 200년 빈도의 홍수사상에 내해 10년, 50년 설계빈도로 건설된 제방의 조건부 비초과확률을 산정하여 지가변동률의 추이를 비교 분석하였다. 분석 결과, 소도시 지역에서는 조건부 비초과확률이 $10\%$ 상승했을 때 순수 연평균지가변동률이 5배정도 상승함을 알 수 있었다.다시 입력자료로 사용하는 업데이트 방식을 사용하기 때문에 예측결과의 오차가 완전하게 보정되지 않으면 다음 결과에 역시 오차를 주게 되어 오차보정이 상당히 중요하다는 것을 알 수 있었다. 오차를 보다 효과적으로 보정하기 위해서는 퍼지제어에 사용되는 퍼지규칙의 수를 늘리고, 유입량에 직접적인 영향을 주는 강우량과 연계한 2변수의 Fuzzy-Grey 모형을 이용한다면 보다 정확한 유입량 예측이 가능할 것으로 사료된다.이 작은 오차를 발생하였으며, 전체적으로 퍼프 모형이 입자모형보다는 훨씬 적은 수의 계산을 통해서도 작은 오차를 나타낼 수 있다는 것을 알 수 있었다. 그러나 Gaussian 분포를 갖는 퍼프모형은 전단흐름에서의 긴 유선형 농도분포를 모의할 수 없었고, 이에 관한 오차는 전단계수가 증가함에 따라 비선형적으로 증가하였다. 향후, 보다 다양한 흐름영역에서 장${\cdot}$단점 분석 및 오차해석을 수행한 후에 각각의 Lagrangian 모형의 장점만을 갖는 모형결합 방법을 제시할 수 있을 것으로 판단된다.mm/$m^{2}$로 감소한 소견을 보였다. 승모판 성형술은 전 승모판엽 탈출증이 있는 두 환아에서 동시에 시행하였다. 수술 후 1년 내 시행한 심초음파에서 모든 환아에서 단지 경등도 이하의 승모판 폐쇄 부전 소견을 보였다. 수술 후 조기 사망은 없었으며, 합병증으로는 유미흉이 한 명에서 있었다. 술 후 10개월째 허혈성 확장성 심근증이 호전되지 않아 Dor 술식을 시행한 후 사망한 예를 제외한 나머지 6명은 특이 증상 없이 정상 생활 중이다 결론: 좌관상동맥 페동맥이상 기시증은 드물기는 하나, 영유아기에 심근경색 및 허혈성 심근증 또는 선천성 승모

• Transactions of Materials Processing
• /
• v.21 no.8
• /
• pp.479-484
• /
• 2012

The objective of this study is to compensate the elastic recovery in the flexible forming process using the predictive models. The target shape was limited to two-dimensional shape having only one curvature radius in the longitudinal-direction. In order to predict the shape error the regression and neural network models were established based on the finite element (FE) simulations. A series of simulations were conducted considering input variables such as the elastic pad thickness, the thickness of plate, and the objective curvature radius. Then, at sampling points in the longitudinal-direction, the shape errors between formed and objective shapes could be calculated from the FE simulations as an output variable. These shape errors were expressed to a representative error value by the root mean square error (RMSE). To obtain the correct objective shape the die shape was adjusted by the closed-loop using the neural network model since the neural network model shows a higher capability of estimating the shape error than the regression model. Finally the experimental result shows that the formed shape almost agreed with the objective shape.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.1
• /
• pp.461-467
• /
• 2021

Among the defect factors that can occur when a wafer-level lens is molded using a thermosetting material, the mold sticking problem of a molded lens during the release process can damage the molded substrate and deform the substrate at the wafer level. An experiment was conducted to examine the factors affecting the demolding force in the lens forming process. The demolding force was examined according to the coating material of the molds. The mold was surface-treated with ITO and Ti, followed by plasma treatment in an O2 atmosphere. A DLC coating was then performed, and the curing and releasability were examined. A coating method for the pull-off experiment was selected based on the results. To measure the demolding force according to the curing process conditions, a method of curing at a constant pressure and a method of curing at a constant position were applied. As a result, the TiO2 surface treatment reduced the release force. When cured by controlling the location, curing shrinkage can reduce the adhesion energy of the interface during curing, resulting in better demolding.

• Geotechnical Engineering
• /
• v.13 no.6
• /
• pp.71-94
• /
• 1997

It is important to evaluate rock strength in order to check stability of a rock slope or to design a structure built on rock. However, test methods used for the evaluation have some difficulties since rock samples provide various deviation of strength due to micro cracks in the samples and teat errors, Also, reliable data have not been accumulated for the rock strength in Korea. Therefore, simple teat methods that can be used easily for investication of rock strength in field or in laboratory are not provided sufficiently yet. This study is to investigate variation of the rock strength due to the degree of weathering and to evaluate the degree of weathering by types of rocks, by using data that have been obtained for several years. Therefore, it is possible to provide a relationship between several rock strength values by performing tests such as uniaxial compression teat, point load test, schmidt hammer teat, absorption ratio best and slaking durability tests. The equations of relationships that can be used to estimate rock strength by using simple test methods in field and in laboratory are proposed.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.19 no.4
• /
• pp.277-287
• /
• 1999

Quasi-static tests such as monotonic tension and loading/unloading tension were performed to investigate the bond characteristics and the failure processes for the T-joint specimens made from fiber/epoxy composite material. Two types of specimens, each consists of two components, e. g. skin and frame. were manufactured by co-curing and secondary bonding. During the monotonic tension test, AE instrument was used to predict AE signal at the initial and middle stage of the damage propagation. The damage initiation and progression were monitored optically using m (Charge Coupled Device) camera. And the internal crack front profile was examined using ultrasonic C-scan. The results indicate that the loads representing the abrupt increase of the AE signal are within the error range of 5 percent comparing to the loads shown in the load-time curve. Also it is shown that the initiation of crack occurred in the noodle region for both co-cured and secondarily bonded specimen. The final failure occurred in the noodle region for the co-cured specimen. but at the skin/frame termination point for the secondarily bonded specimen. Based on the results, it was found that two kinds of specimen show different failure modes depending on the manufacturing methods.

• Composites Research
• /
• v.33 no.2
• /
• pp.44-49
• /
• 2020

The cure kinetics of carbon fiber-reinforced prepreg for Vacuum Bag Only(VBO) process was studied by differential scanning calorimetry (DSC). The total heat of reaction (ΔH_total = 537.1 J/g) was defined by the dynamic scanning test using prepregs and isothermal scanning tests were performed at 130℃~180℃. The test results of isothermal scanning were observed that the heat of reaction was increased as the temperature elevated. The Kratz model was applied to analyze the cure kinetics of resin based on the test results. To verify the simulation model, the degree of cure from panels using different cure cycles were compared with the measurement. The simulation model showed that the error against the experimental value was less than 3.4%.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.6
• /
• pp.1754-1759
• /
• 2008

To produce plastic parts that have fine pattern through conventional injection molding, a lot of difficulties follow. Therefore, rapid heating and cooling methods are good candidates for manufacturing injection-molded parts with micro/nano patterns. In this study, we adopted the E-Mold patent technology. The mold for E-Mold technology has a separate heated core with micro heaters. It is very important to optimize the lay-out of the heaters in heated core because it influences both control and distribution of mold temperature. We developed a optimization method of heating line lay-out by using commercial softwares and compared the output with the experimental results. We used Pro-Engineer Wildfire 2.0 for the mold design, ICEMCFD for mesh generation, and FLUENT for heat transfer simulation. The simulation results showed the temperature profile from $60^{\circ}C$ to $120^{\circ}C$ or $180^{\circ}C$ during heating and cooling process which were compared with the injection molding experiments. We concluded that the simulation could well explain the experimental results. It was shown that the E-Mold optimization design for heater lay-out could be available through the simulation.

• Proceedings of the IEEK Conference
• /
• 2000.06d
• /
• pp.70-73
• /
• 2000

The error diffusion is good for reproducing continuous image to binary image. However the reproduction of edge characteristics is weak in power spectrum analysis of display error. It is suggested for us an edge-enhanced error-diffusion method that is included pre-processing algorithm for edge characteristic enhancement. Pre-processing algorithm is organized horizontal and vertical directional 2nd order differential values and weighting function of pre-filter. The improved Error diffusion using pre-filter, presents a good results visually which edge characteristics is enhanced. The performance of the proposed algorithm is compared with that of the conventional edge-enhanced error diffusion by measuring the RAPSD of display error, the egde correlation and the local average accordance.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.31 no.11
• /
• pp.1053-1058
• /
• 2007

Micro-EDM technology (or the manufacture of miniature parts is used to make a micro hole. Two electrode shaping methods, mechanical electrode grinding and WEDG technique, have been studied. In this study, an electrode shaping method by using previously machined hole is introduced in order to obtain an optimal hole-making condition. Key factors such as applied voltage, capacitance, feedrate, and hole-dimension have an influence on the fabricating error of electrode shaping, which are taper ratio of a hole, electrode form accuracy, and electrode surface. Therefore, we try to investigate the optimal fabricating of electrode shaping from various experiments. Results from experiments, it was able to minimize the electrode fabricating error as voltage increases, and also applied feedrate and capacitance decreases.