• Journal of the Korean Wood Science and Technology
• /
• v.36 no.4
• /
• pp.19-25
• /
• 2008

This study was carried out to investigate the bending strength properties of the unreinforced glulam beams and the GFRP laminated glulam beams according to the volume ratio of GFRP. The 7-layer glulam beams ($10cm(b){\times}14cm(h){\times}180cm(l)$) were manufactured, using Larch (Larix kaempferi Carr.) laminae ($2cm(h){\times}10cm(b){\times}360cm(l)$), which were dried to the moisture content of 8% and specific gravity of 0.54. GPRP of 0.1 and 0.3 cm was reinforced between the outmost layer of bottom and next layer. When the glulam beams were reinforced with GFRP at the volume ratio of 0.7% and 2.1%, respectively, the bending strength was increased by 12% and 28%, respectively, in the reinforced beams than in control glulam beams. Also, the GFRP reinforced layer of the glulam beams with GFRP laminations blocked the progression of rupture, and the unbroken part held about 90% of the bending strength. In the results of glue joints test, the block shear strength is higher than $7.1N/mm^2$, the standard of KS F3021, and in the result of delamination, the adhesive strength is good as the water soaking and boiling delamination was less than 5%.

• Composites Research
• /
• v.22 no.3
• /
• pp.82-88
• /
• 2009

The effect of open and filled holes on the strength behavior of carbon fiber reinforced polymeric (CFRP) composites was investigated. The strength was measured at room temperature dry, cold temperature dry, $-55^{\circ}C$, and elevated temperature wet, $108.3^{\circ}C$ on several different laminate configurations. Based on the experimental data presented, it is shown that the filled hole tensile strength is larger than that of open hole by reducing damage around the hole due to the constraint imposed by the fastener. The tensile strength at cold temperature dry, $-55^{\circ}C$ is increased with the brittleness by the thermal expansion coefficient of fiber and matrix. The compressive strength at elevated temperature wet, $108.3^{\circ}C$ is decreased by the cause of interfacial deterioration between fiber and matrix with moisture absorption.

• Composites Research
• /
• v.17 no.3
• /
• pp.38-44
• /
• 2004

The electromagnetic interference (EMI) shielding is very essential for commercial and military purposes. We fabricated multi-walled carbon nanotube (MWNT)/epoxy composites and studied the electromagnetic characteristics of the composites before we study the characteristics of MWNT-added glass fiber-reinforced composites. After setting up the fabrication process, we measured the permittivity of MWNT/epoxy composites with process variables and MWNT concentrations in X-band (8.2GHz~12.4GHz). We also observed re-aggregation phenomenon of MWNTs and investigated its effect on the permittivity. The permittivity of the composites was influenced by the degree of dispersion of MWNTs and increased almost linearly as MWNT concentration increases.

• Composites Research
• /
• v.27 no.3
• /
• pp.103-108
• /
• 2014

Fiber reinforced polymer plastic (FRP) structural members are recently available in construction industries due to various material properties such as high specific strength and stiffness, light-weight, and corrosionresistance. The floating PV generation structure can also be an illustration for applying FRP in construction applications. The floating PV generation structure has been recently issued as a representative item for the low carbon and green growth campaign and many related studies have been conducted for the structural safety and commercial viability. Moreover, the floating PV generation structures for the commercial purpose have been constructed. In this paper, the investigation and development processes of elements for the floating PV generation structure are presented during commercialization.

• Composites Research
• /
• v.29 no.2
• /
• pp.66-72
• /
• 2016

Porosity in polymer matrix composites increases rapidly during thermochemical decomposition at high temperatures. The generation of pores reduces elastic moduli and failure strengths of composite materials, and gas pressures in internal pores influence thermomechanical behaviors. In this paper, micromechanical finite element analysis is carried out by using two-dimensional representative volume elements for unidirectionally fiber-reinforced composites with porous matrix. According to the state of the pores, effective elastic moduli, poroelastic parameters and failure strengths of the overall composites are investigated in detail. In particular, it is confirmed that the failure strengths in the transvers and through-thickness directions are predicted much more weakly than the strength of nonpored matrix, and decrease consistently as the porosity of matrix increases.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.6
• /
• pp.757-762
• /
• 2010

Owing to the high specific strength and stiffness of composite materials, they are extensively used in mechanical systems and in vehicle industries. However, most mechanical structures experience repeated load and fatigue. Therefore, it is important to perform fatigue analysis of fiber-reinforced composites. The properties of composite laminates vary depending upon the stacking sequence and stacking direction. Fatigue damage of composite laminates occurs according to the following sequence: matrix cracking, delamination, and fiber breakage. In this study, fatigue tests were performed for damage analysis. Fatigue damages, which have to be considered in fatigue analysis, are determined by using the stiffness values calculated from hysteresis loops, and the obtained fatigue damage curve is examined using Mao's equation and Abdelal's equation.

• Korean Journal of Materials Research
• /
• v.3 no.1
• /
• pp.84-94
• /
• 1993

This paper deals with the fatigue properties of chopped strand glass mat/polyester composite to understand the effect of water absorption on fatigue behavior of GFRP. The fatigue crack in the both no water and a water absorption materials initiated at the initial of cycle. Thereafter, it was divided with two regions that one decreased with the crack extension and the other increased with the crack extension. The absorption of distilled water degrades the bond strength between fiber and matrix, there, by the tendency of fiber pull-out is increased in perpendicular to crack growth deirection and the debonding of fibers increased to the place which is parallel to crack growth direction. Therefore, the reduction of fatigue strength was caused by these factors.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.12
• /
• pp.2328-2339
• /
• 1992

The propagation of coherent time-harmonic elastic L-and SV-waves is studied in a medium with random distribution of cylindrical inclusions. The purpose of the research is to characterize the dynamic elastic moduli and the attenuation properties of fiber-reinforced composite materials. The cylindes representing the fibers are assumed to be distributed in parallel with each other and the direction of incident waves are normal to the cylinder axes. A multiple scattering formula using the single scattering coefficients in conjunction with the Lax's quasicrystalline approximation is derived from which the dispersion relation for such medium is obtained. In order to formulate the multiple scattering interaction between cylinders, the pair correlation functions are generated by the Monte Carlo simulation technique. From the numerically evaluated complex wavenumbers, the propagation speed of the average wave, the coherent attenuation and the effective elastic moduli are presented as functions of frequency and fiber volume fraction.

• Composites Research
• /
• v.26 no.3
• /
• pp.189-194
• /
• 2013

This paper deals with the study of mechanical properties and impact energy absorbed by composites, made by using thermoplastic and thermoset as matrix, flax fiber and nanoclay as reinforcements. The nanoclay was sprayed on the fiber laminate directly after mixing with ethanol. This experiment designed by Taguchi method and have variable factors, i.e three types of fiber direction(F), three different nanoclay wt%(N) and three spray gun hole shapes(S). According to these conditions, composites were made and the optimum conditions were found to be F1N3S1, F1N2S1, F1N2S1 and F3N2S1 for thermoplastic, and F1N3S2, F1N3S2, F1N2S2 and F3N2S1 for thermoset which were matched with tensile strength, modulus, total impact absorbed energy and heat release rate respectively.

• The Korean Journal of Rheology
• /
• v.8 no.1
• /
• pp.49-57
• /
• 1996

단섬유 강화복합재료의 가공공정에 있어서 유동 중에 일어나는 섬유 배향상태를 정 확히 예측하고 제어하는 일은 대단히 중요하다. 본 연구에서는 섬유현탁액의 거동을 살펴보 기 위하여 뉴톤유체를 매질로하는 섬유현탁액을 대상으로 하여 유변학적 해석을 하였다. 이 를 위해 섬유간 상호계수는 섬유배향상태의 함수의 섬유간 평균거리를 이용하여 계산하였는 데, 섬유간 평균거리는 변형된 Doi-Edwards의 방법을 이용하였다. 축대칭 압출팽창 문제를 예로 수치모사를 하여 본 저자들이 앞서 행한 결과와 비교하였다. 유동장을 축대칭 이차원 으로 하고 섬유배향을 삼차원 모두 고려하여 구한 수치모사의 결과는 실험과 잘 일치하였 다. 진한 섬유현탁액의 경우 섬유간 상호계수는 중요한 인자로서 이것을 섬유 배향상태에 의존하는데 이섬유간 상호계수를 섬유간 거리와 섬유배향상태의 함수로 나타내는 방법을 사 용하여 보다 실제적인 해석을 할수 있었다.