• Journal of Dental Rehabilitation and Applied Science
• /
• v.29 no.2
• /
• pp.111-118
• /
• 2013

Purpose of present study is to investigate the effects of thread pitch in coronal portion in scalloped implant with 2 different connections on loading stress using 3 dimensional finite element analysis. Scalloped implant with 4 different thread pitches (0.4mm, 0.5mm, 0.6, and 0.7mm) in the coronal part was modeled with 2 different implant-abutment connections. Platform matching connection had the same implant and abutment diameter so that they were in flush contact at the periphery while platform mismatching connection had smaller abutment diameter than implant so that their connection was made away from periphery of implant-bone interface. Occlusal loading of 100N force was applied vertically and 30 degree obliquely to all 8 models and the maximum von Mises bone stress was identified. Loading stress as highly concentrated in cortical bone. Platform mismatching scalloped implant with small thread pitch (0.4mm) model had consistently lowest maximum von Mises bone stress in vertical and oblique loads. Platform matching model had lowest maximum von Mises bone stress with 0.6mm thread pitch in vertical load and with 0.4mm thread pitch in oblique load. Platform mismatching connection had important roles in reducing maximum von Mises bone stress. Scalloped implant with smaller coronal thread pitch showed trend of reducing maximum von Mises bone stress under load.

• Journal of the Korean Institute of Gas
• /
• v.13 no.1
• /
• pp.1-8
• /
• 2009

Recently, the vibration of underground structure due to high speed railway loads has been increased substantially as compared with middle and slow speed. The buried gas pipelines under continuous impact forces and repeated loading are more influenced by the vibrational loads than another pipelines. However, the static analysis was not enough to allow for the effect of vibrations because it uses impact factors for the design or analysis process. In this study, characteristics of Pipelines was quantitatively estimated through each conditions of soil covers and train speed, and the new vibration prediction is presented about the vibrational velocity.

• Journal of Korean Association for Spatial Structures
• /
• v.6 no.1 s.19
• /
• pp.75-82
• /
• 2006

The single layer latticed dome is very sensitive on the slenderness ratio and half open angle of the elements, load condition, and the connection type because it is organized by a lot of thin elements, so we have to use the geometrically nonlinear buckling load when the buckling of the structures is analyzed. But, it is very difficult to design the single layer latticed domes considered all renditions. Therefore the purpose of this paper is to propose the appropriate design method of the single layer latticed dome considered the geometrically nonlinear buckling load in base of the linear buckling load by the eigenvalue analysis.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.2 no.3
• /
• pp.15-22
• /
• 1982

This paper presents analytic bending moment solution and resonance diagrams for a uniform beam of infinite length subjected to anaxial force and moving transverse load. Solutions are obtained that are time invariant in a coordinate system moving with the load velocity. The supporting foundation includes damping effects. The influences of the axial force, damping coefficient and load velocity on the beam response are studied. The limiting case of no damping and critial damping are also investigated. The profiles of the mement of the beam is shown graphically for several values of the load speed, the axial force and damping parameters.

• Journal of the Korean GEO-environmental Society
• /
• v.9 no.5
• /
• pp.71-81
• /
• 2008

Active earth pressure formula, which can consider the effects of ground surface inclination, inclination of inside retaining wall face, wall friction, line load, uniform load, soil cohesion and adhesion, was derived based on the force equilibrium principle. In order to verify the accuracy of this proposed formula, the calculated active earth pressures by the proposed formula were compared with those of graphical solutions. Also, the active earth pressures determined by the proposed formula were compared with those by Coulomb's, Rankine's and Mazindrani's solution under specific conditions. The results matched quite well not only with the graphical solutions but also with those by three other methods. Also, the trend of active earth pressures by the proposed formula were corresponded with results of experimental study by Fang, et al. It can be concluded that this generalized formula not only can overcome the limitations of Rankine's, Coulomb's and Mazindrani's active earth pressure formula but also can consider the external loading conditions.

• Journal of the Korean Geotechnical Society
• /
• v.34 no.12
• /
• pp.43-58
• /
• 2018

In this study, the load-transfer behavior along the shaft of the prebored and precast piles was investigated by pile loading tests. Special attention was given to quantifying the skin frictions developed between the pile-soil interfaces of the 14 instrumented test piles. Based on this detailed field tests, the load - settlement curves and axial load distributions of piles were obtained and the load-transfer curves (t-z curves) for the test piles were proposed. As such, it is found that the test results show two different load transfer behaviors; ductile and brittle behavior curves. The corresponding t-z curves are proposed based on the hyperbolic- and sawtooth-shape, respectively. By validating the accuracy of the proposed curves, it is also found that the prediction results based on the proposed load-transfer curve are in good agreement with the general trends observed by the field loading tests.

• Aerospace Engineering and Technology
• /
• v.12 no.1
• /
• pp.213-220
• /
• 2013

Korean Lunar Explorer is planned to be launched in the 2020s according to national space development strategy. The Lunar Explorer will be developed as two unmanned light weight models: a lunar orbiter and a lunar lander. The Lunar Explorer's structure should be designed to have light weight due to constraints from launcher as well as to provide structural safety against launch load, in-orbit condition and landing condition and to serve accommodation space for mission equipment. Core technology related to structural development of lunar explorer should be developed in advance. Especially, for lunar lander, technology for developing landing gear which enables lander to land safely on lunar surface is required essentially. This paper deals with structural development of lunar lander ground test model including design, manufacturing and test.

• The Bulletin of The Korean Astronomical Society
• /
• v.37 no.2
• /
• pp.193.2-193.2
• /
• 2012

달착륙선 등과 같은 특수 목적을 위해 제작된 우주용 착륙선에는 착륙 시 전달되는 충격하중이 탑재장비로 전달되지 못하도록 연착륙(soft-landing)을 위한 충격흡수 메커니즘이 구현되어 있어야 한다. 일반적으로 자동차 및 항공기에서는 실린더와 피스톤으로 구성된 유공압식 완충장치를 주로 사용하여, 피스톤 압축으로 실린더 내부 오일 또는 압축공기가 오리피스를 통하여 분출됨에 따라 유체마찰 에너지를 활용한 충격 흡수장치가 일반적이다. 그러나 이와 같은 지상 장비용 유공압식 충격흡수 메커니즘은 진공 및 무중력 우주 환경하에서 오리피스 기능 상실, 유압유 기화 현상 및 극저온/고온 환경에서의 성능저하 등의 문제점으로 인하여 우주용 착륙선 충격완충장치로 적용이 불가능하다. 따라서 기존의 우주용 착륙선의 대부분은 충격에너지를 기계적인 좌굴 소성 변형에너지로 변환하여 충격을 흡수할 수 있도록 알루미늄 허니콤을 주로 많이 사용하여 왔다. 본 연구에서는 진공 및 무중력 우주환경에서 착륙선 충격완충 장치로 적용이 가능하도록 실리콘 포옴과 스프링을 조합하여 구성하였으며, 충격완충 매체로 유압유 및 공압을 대체할 수 있도록 실리콘 포옴을 후방 사출 성형 방식으로 적용하여 오리피스를 통과한 실리콘 포옴의 변형에너지로 충격에너지를 흡수하게 함으로서 착륙 완충효율을 극대화 할 수 있도록 검토하였다.

• Journal of the Korean Society for Railway
• /
• v.11 no.5
• /
• pp.499-503
• /
• 2008

The catenary line and feeder line installed on same electrical pole in opened place of AC electrical rail-road. The Electrical pole has receive a different weight from the catenary line and feeder line. So we have designed the Feeder supporting metal with new shape and material based on this fact. And then we have examined the stability of Feeder supporting metal designed a steel pipe by FEM program. New steel pipe compared with existing steel pipe on a economy respect. That result give proof the stability and economy as feeder supporting steel. There-fore this device have a basic of Value Engineering, so we have the need of reflection to design as a device of new electrical pole.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.7 no.5
• /
• pp.57-66
• /
• 2003

In order to verify the applicability of the developed modified parallel IWAN model. two types of cyclic torsional shear tests were performed using Kum-Kang and Toyoura sands. One was a symmetric-limit loading test and the other was an irregular loading test. Model parameters were derived from the symmetric limit loading tests at various relative densities and confining pressures. The modified parallel IWAN model can predict the cyclic hardening behavior of sands very well as increasing loading cycles in the symmetric-limit tests. Irregular loading tests were performed using the loading shape suggested by Pyke(1979). Cyclic behaviors under irregular loading were simulated using model parameters derived from symmetric limit loading test results of similar loading conditions. The predicted cyclic hardening behaviors under irregular loading matched well with experimental results and the applicability of the proposed model was verified.