• Journal of Korean Society for Geospatial Information Science
• /
• 제5권1호
• /
• pp.147-157
• /
• 1997

A national program for GIS Training had been established by a feasibility study which was performed during the period of from July, 1995 through April, 1996 initiated by Ministry of Science and Technology (MOST). Systems Engineering Research Institute (SERI), one of government-supported institutes in the fields of software development, have taken in charge of Korean GIS training program with emphases on short courses since July, 1996. To distinguish these national programs from those of major commercial GIS software vendor, GIS training programs by executing staffs within SERE have been established with the basis of its own educational paradigm; therefore, they was composed of several specific training curricular developed by executing staffs. In this paper, the practical aspects during execution and progress of these programs are described, and all courses named after decision maker course, GIS manager course, and user course in the first year of GIS training program are evaluated with questionnaire result riven to the trainees. As results, the satisfaction-rate after the decision maker, the GIS manager, and the user course is 84.8%, 81.2%, and 66.7% respectively These whole results are shown as more affirmative ones than expected, and each result, as a kind of feedback of this executing program, plays an important role to flourish Korean GIS training project in future.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• 제25권4호
• /
• pp.127-134
• /
• 2015

Aluminum nitride (AlN) single crystals have attracted much attention for a next-generation semiconductor application because of wide bandgap (6.2 eV), high thermal conductivity ($285W/m{\cdot}K$), high electrical resistivity (${\geq}10^{14}{\Omega}{\cdot}cm$), and high mechanical strength. The bulk AlN single crystals or thin film templates have been mainly grown by PVT (sublimation) method, flux method, solution growth method, and hydride vapor phase epitaxy (HVPE) method. Since AlN suffers difficulty in commercialization due to the defects that occur during single crystal growth, crystalline quality improvement via defects analyses is necessary. Etch pit density (EPD) analysis showed that the growth misorientations and the defects in the AlN surface exist. Transmission electron microscopy (TEM) and electron back-scattered diffraction (EBSD) analyses were employed to investigate the overall crystalline quality and various kinds of defects. TEM studies show that the morphology of the AlN is clearly influenced by stacking fault, dislocation, second phase, etc. In addition EBSD analysis also showed that the zinc blende polymorph of AlN exists as a growth defects resulting in dislocation initiator.

• International Commerce and Information Review
• /
• 제15권4호
• /
• pp.241-265
• /
• 2013

The purpose of this paper is to examine the Banks's Examination of Documents in the L/C Transactions. Most of all, this article deals with one of most important aspects of the law on documentary credits, namely, the compliance of documents presented with the terms and conditions of a letter of credit. In addition, the general principles of strict compliance will be considered and in the next, the requirements of specific documents such as invoices, transport documents and insurance policies. This area of letter of credit law is shaped not only by judge-made decisions but also the articles of Uniform Customs and Practice for Documentary Credits, the International Standard Banking Practice(ISBP Publication No.745) prepared by the Banking Committee of the International Chamber of Commerce as well as the position papers and opinions of the latter. Whether a document complies with the terms of a letter of credit is essentially a matter of examination and construction of the document in question against the terms of the letter of credit under which it is presented, articles of the UCP, ISBP as well as the opinions and statements of the Banking Committee. Most of all this article was focused on provisions of UCP600. Comparison with provisions of UCP500 have been drawn where appropriate.

• Journal of the Korean Society of Food Science and Nutrition
• /
• 제12권2호
• /
• pp.99-104
• /
• 1983

Chemical changes of major tea constituents by tea manufacture were examined by the quantitative masurements of tannin, caffeine, free sugars and total amino acid. The sample used in this experiments was fresh green and black tea leaves, green tea prepared by classical panning process and black tea prepared by commercial process. The results obtained are as follows: Compared with fresh tea leaves, tannin was increased 2% in green tea and decreased 56.5% in black tea by tea manufacture. Caffeine was increased 25.9% in green tea and decreased 3.1% in black tea. Total free sugars were decreased 78.2% and 76.7% in green tea and black tea, respectively. Total amino acids were decreased 26.1% and 18.8% in green tea and black tea, respectively.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 한국정보통신학회 2017년도 춘계학술대회
• /
• pp.559-562
• /
• 2017

In city, tracing of power transmission lines is difficult due to compound installation of overhead and underground lines, transposition, bad view caused by trees or big buildings. It is hard problem for electrical technician on site to trace power transformers or power lines to serve customers in 3 phase -4 wires power distribution systems. It is necessary that the correct and fast tracing method is required for load balancing among distribution lines. Old technology use to trace off-lines with high power impulse injection. Our proposed method use to trace live lines with very small power high frequency signal injection. Typical power transformers in the distribution system prevent propagating the higher frequency carrier signal. The proposed method uses the limited propagation ability to identify the power transformer to serve customers. Two end communication terminals are required to be synchronized between them for determination on electrically same phases. Challenging issue is to achieve synchronization without GPS providing synchronizing time. A novel power transformer and wire identification system is designed and implemented. The system consists of a transmitter and a receiver with power-line communication module. Some experiments are conducted to verify the theoretical concepts in a big commercial building. Also some simulations are done to help and understand the concepts by using MATLAB Simulink simulator.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 한국정보통신학회 2016년도 춘계학술대회
• /
• pp.505-508
• /
• 2016

In city, tracing of power transmission lines is difficult due to compound installation of overhead and underground lines, transposition, bad view caused by trees or big buildings. It is hard problem for electrical technician on site to trace power transformers or power lines to serve customers in 3 phase -4 wires power distribution systems. It is necessary that the correct and fast tracing method is required for load balancing among distribution lines. Old technology use to trace lines with high power impulse injection. Our proposed method uses to trace lines with very small power high frequency signal injection. Simulation models for 3-phase power transformers, 3-phase wire lines, and customer loads are described to investigate the transmission characteristics of high frequency power line carrier. Distribution lines have only a limited ability to carry higher frequencies. Typically power transformers in the distribution system prevent propagating the higher frequency carrier signal. The proposed method uses the limited propagation ability to identify the power transformer to serve customers. The system consists of a transmitter and a receiver with power-line communication module. Some experiments are conducted to verify the theoretical concepts in a big commercial building. Also some simulations are done to help and understand the concepts by using MATLAB Simulink simulator.

• Korean Journal of Construction Engineering and Management
• /
• 제17권4호
• /
• pp.76-86
• /
• 2016

Recently, the Contracts of International Construction Business has been decreased from the beginning of 2015 in Korea, although it has been steadily increased until 2014. This trend could be caused by Low-Price Contracts, the lack of Know-how and experience in operating, the poor management of Claims and Low-Profitability in Business. It has been recognized that the qualitative improvement of Business Contacts are necessary for successful Projects. In the Bidding Process, therefore, Experience data as In-House Data and Lessons Learned for projects should be strategically involved to assure riskless offers. Accordingly the Proposal Process are needed to be organized and enhanced by including processes for risks review about technical, marketing and commercial part during the bidding. This paper proposes a Risk Management Process model during Bidding Phase, using Risk Evaluation Method through the project life-cycle. The Concept of Model is to define CSF (Critical Success Factor) in the bidding process and Risk Factors are linked to CSF and Organization based on RAM (Responsibility assignment matrix).

• Journal of the Korea Society of Computer and Information
• /
• 제12권4호
• /
• pp.249-256
• /
• 2007

AIn this paper, a new desist of LDI controller IC for general purpose is proposed for driving the LDI(LCD Driver Interface) controller in $4{\sim}9$ inches sized portable small-medium TFT-LCD(Thin Film Transistor addressed -Liquid Crystal Display) panel module. The designed LDI controller was verified on the FPGA(Reld Programmable Gate Array) test board, and was made the interactive operation with the commercial TFT-LCD panel successfully. The purpose of design is that it is standardized the LDI controller's operation by one LDI controller for driving all TFT-LCD panel without classifying the panel vendor, and size. The main advantage for new general-purpose LDI controller is the usage for the desist of all panel's SoG(System on a Glass) module because of the design for the standard operation. And in the previous method, it used each LDI controller for every LCD vendor, and panel size, but because a new one can drive all portable small-medium sized panel, it results in reduction of LDI controller supply price, and manufacturing cost of AV(Audio Video) board and panel. In the near future, the development of SoG IC(Integrated Circuit) for manufacturing more excellent functional TFT-LCD panel module is necessary. As a result of this research, the TFT-LCD panel can make more small size, and light weight, and it results in an upturn of domestic company's share in the world market. With the suggested theory in this paper, it expects to be made use of a basic data for developing and manufacturing for the SoG chip of TFT-LCD panel module.

• Korean Journal of Agricultural Science
• /
• 제35권2호
• /
• pp.193-198
• /
• 2008

This experiment is a quantitative experiment where insoluble Vitamins E and K are extracted from the yolk of the spawning which was fed by by-products of tangerine, carrot, or Japanese apricot. Finally the purpose is to raise contents of the insoluble Vitamins E and K inside the yolk of the spawning. The saponification method through ${\alpha}$, ${\alpha}$ - dipyridyl was used to determine the content of Vitamin E. Diethyl dithiocarbamate assay was used to examine the content of Vitamin K. The contents of Vitamin E in egg yolks of chicken fed by by-products of tangerine, carrot, or Japanese apricot increased 2 - 3 times compared to control egg, while the contents of Vitamin K almost no changed.

• Journal of Adhesion and Interface
• /
• 제2권3호
• /
• pp.25-32
• /
• 2001

Ethyl cyanoacrylate (ECA) is used as an instant adhesive, and it can be readily polymerized by moisture in air without any initiator and applied for industrial products and ohome use. However, pure ECA monomer is low-viscosity liquid at room temperature that flows into substrate surface. To thicken the instant adhesive, poly(methyl methacylate)(PMMA) is often added in it commercially. Another disadvantage of instant adhesive polymer is its brittleness In this study, functional polymers including PMMA for an additive of ECA were prepared to increase viscosity of the monomer and flexibility of the adhesive atthe same time The additives, P(MMA-VAc-EVE), were synthesized by radical copolymerization of MMA with VAc and EVE having low glass transition temperature (Tg). The additives were added to ECA to get functional instant adhesives. The chemical structures of the additives and ECA polymers were confirmed by $^1H$ NMR and FTIR, and their physical and mechanical properites were also evaluated. The Tg of the obtained additives decreased with increasing the content of VAc or VAc-EVE, indicating more improved flexibility. In addition, functional instant adhesive containing the additives showed higher bonding strength than that of the existing one.