• Corrosion Science and Technology
• /
• v.11 no.3
• /
• pp.96-102
• /
• 2012

Outer diameter stress corrosion cracking (ODSCC) has occurred for Alloy 600 (Ni 75 wt%, Cr 15 wt%, Fe 10 wt%) as a heat exchanger tube of the steam generator (SG) in nuclear power plants (NPP) during long term operation. Among many causes for SCC, lead (Pb) is known to be one of the most deleterious species in the secondary system. In the present work, the oxide formed on Alloy 600 was characterized as a function of the PbO content in 0.1 M NaOH at $315^{\circ}C$ by using an electrochemical impedance spectroscopy (EIS), a transmission electron microscopy (TEM), equipped with an energy dispersive x-ray spectroscopy (EDS). The oxide property was analyzed in view of SCC susceptibility.

• Journal of the Korean Ceramic Society
• /
• v.38 no.11
• /
• pp.1000-1007
• /
• 2001

In an evacuated tube solar collector, the stable sealing of the heat pipe to the glass tube is important for the collector to use for a long period of time. The sealing of copper tube to the glass is quite difficult because of the large differences in the physical and chemical properties of the two materials. In this study, therefore, a proper copper oxide layer was induced to improve the chemical bonding of the two materials, and the oxidation state of copper and the interface between copper and glass were examined by XRD, SEM and EDS. Its bonding strength was also measured. Cu$_2$O was formed when the bare copper was heat-treated under 600$^{\circ}C$, while CuO oxide layer was formed above that temperature. The bonding state of CuO to the copper was very poor. The borate treatment of the copper, however, extend the stable forming of Cu$_2$O layer to 800$^{\circ}C$. Borosilicate glass tube was sealed to a copper tube by Housekeeper method only when the sealing part was covered with Cu$_2$O layer. The bonding strength at the interface was measured 354.4N, its thermal shock resistance was acceptable.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.62-62
• /
• 2003

금속-실리콘간 화합물인 실리사이드 중에서, 코발트다이실리사이드(CoSi$_2$)는 비저항이 낮고 선폭이 좁아짐에 따라 면저항이 급격히 증가하는 선폭의존성이 없으며 화학적으로 안정한 재료로 현재 널리 이용되고 있는 재료이다. 또한, 실리콘 (100) 기판과 에피택셜하게 성장한 CoSi$_2$는 우수한 열안정성 과 낮은 juction leakage의 특성을 가지며, shallow junction 형성을 가능하게 하는 많은 장점을 가지고 있어 각광받고 있다. 그러나 순수한 Co의 증착 후속 열처리에 의해 형성된 CoSi$_2$는 (110), (111), (221)등의 다양한 결정방위를 가지게 되어 에피택셜 하게 형성되기 어렵다. 현재까지 Ti, Ta, Zr과 화학 산화막 등의 확산 방지막을 이용하여 에피 택셜하게 성장시키는 많은 방법들이 연구되어 왔으며, 최근에는 본 연구실에서 반응성화학기상증착법으로 Co-C 박막을 증착하여 in-Situ로 에피택셜 CoSi$_2$를 형성하는 새로운 방법을 보고하였다. 본 연구는 반응성 스퍼터링에 의해 증착된 Co-N 박박으로부터 후속 열처리를 통하여 에피택셜 CoSi$_2$를 성장시키는 새로운 방법을 제시하고자 한다. Co-N 박박은 Ar과 $N_2$의 혼합가스 분위기 속에서 Co를 스퍼터링하여 증착하였다. 증착시 혼합가스 내의 $N_2$함량의 변화에 따라 다양한 Co-N 박막이 형성됨을 확인하였다. 후속열처리시 Co-N 박막의 산화를 방지하기 위하여 Ti층을 마그네트론 스퍼터링으로 증착하였으며, Ar 분위기에서 온도에 따른 ex-situ RTA 열처리를 통하여 에피택셜 CoSi$_2$를 성장시킬 수 있었다. 이러한 에피택셜 CoSi$_2$는 특정 한 Ar/$N_2$ 비율 내에서 성장이 가능하였으며, 약 $600^{\circ}C$이상의 열처리 온도에서 관찰되었다.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.242.1-242.1
• /
• 2011

산화물 반도체는 높은 이동도와 낮은 공정 온도, 넓은 밴드갭으로 인한 투명성등 많은 장정을 가지고 있어 최근 많이 연구되고 있다. 그 중에서도 InGaZnO (IGZO)는 In, Ga 함유량으로 박막의 전기적 특성을 쉽게 조절할 수 있고 상온에서 비정질 상태로 증착되어 균일성에 장점이 있다. IGZO 박막을 TFT에 적용 시 MOSFET과는 다르게 축적 상태에서 채널이 형성되기 때문에 산화물 반도체 내에 캐리어 농도는 TFT 특성에 많은 영향을 미친다. 또한, 실리콘 기반의 트랜지스터는 이온 주입 및 확산 공정을 통해서 선택적으로 $10^{20}/cm^3$ 이상의 고농도 도핑을 실시하여 좋은 트랜지스터 특성을 확보할 수 있으나 IGZO 박막에는 이러한 접근이 불가능하다. 따라서 IGZO 박막의 캐리어 농도를 조절할 수 있으면 소스/드레인과 반도체의 접촉 저항 감소 및 전계 효과 이동도등 많은 특성을 개선할 수 있다. 본 연구에서는 UV light를 이용하여 IGZO 박막의 캐리어 농도를 조절하였다. IGZO 박막은 UV light 조사로 인해 Mo와 IGZO박막의 접촉저항이 $3{\times}10^3\;{\Omega}^*cm$에서 $1{\times}10^2\;{\Omega}^*cm$로 감소하였다. 이는 UV 조사로 표면에 금속-OH 결합이 생성되어 IGZO 박막의 캐리어 농도가 ${\sim}5{\times}10^{15}/cm^3$에서 ${\sim}3{\times}10^{17}/cm^3$까지 증가하기 때문이다. 또한 표면에 생성된 OH기는 강한 친수성 성질을 보여주고 표면의 높은 에너지 상태는 Self-Assembly Monolayer (SAM) 공정 적용이 가능 하다. 본 실험에서는 SAM 공정을 적용하여 IGZO-based TFT 제작에 성공하였고, 이 TFT는 UV 조사 시간에 따라 전계 효과 이동도가 0.03 $cm^2/Vs$에서 2.1 $cm^2/Vs$으로 100배 정도 증가하였다.

• Electrical & Electronic Materials
• /
• v.4 no.1
• /
• pp.38-44
• /
• 1991

본 연구는 전기로에 의한 열 산화법에 의해 SiO$_{2}$(88[.angs.])와 ONO(89[.angs.])를 성장시켜 MIS capacitor를 제작한 후, 초 박막 유전체/실리콘 계면에서 전자파 간섭 효과를 실험적으로 비교 검토한 것이다. EWIE현상의 결과로서 첫째. 저 전계영역에 비해 고 전계영역에서 우세하며 둘째. SiO$_{2}$에 비해 ONO가 약하게 나타난다. 그러므로 ONO가 SiO$_{2}$보다 열 전송자 효과에 대한 저항성이 우수함을 알 수 있고 ULSI급의 게이트 절연막으로서의 실용가능성을 확인하였다.

• Korean Journal of Crystallography
• /
• v.10 no.1
• /
• pp.9-12
• /
• 1999

TiO2로 수열코팅하여 표면 개질한 흑연의 미세구조 및 전기적 특성에 관하여 연구하였다. 수열합성에 의해 코팅된 TiO2는 rutile 상이였고, 흑연의 소결정을 증대하였다. 온도에 따라 흑연의 소결성 및 밀도는 증가하였고, 코팅된 TiO2에 의한 흑연의 산화로 저항은 증가하였고 1100℃ 이상에서는 포화되었다.

• Journal of the Korean Magnetics Society
• /
• v.8 no.5
• /
• pp.282-287
• /
• 1998

Dependence of magnetoresistance on base pressure and deposition rates of each Fe, Co, Cu layers in the $Fe(50{\AA}/[Co(17{\AA})/Cu(24{\AA})]_20$ multilayer thin films, prepared by dc magnetron sputtering on Corning glass, were investigated. AFM analysis, X-ray diffraction analysis, vibrating sample magnetometer analysis, and magnetoresustance measurement (4-probe method) were performed. The multilayer films deposited under low base pressure increases magnetoresistance ratio by preventing oxidation. Annealing for the samples at a moderate temperature allowed larger textured grain with no loss in the periodicity. Magnetoresistance ratio of the annealed multilayers was increased due to the increase antiferromagnetically coupled fraction of the film after annealing. Optimization of deposition rate was greater than 1 $\AA$/s for Fe, and 2.8 $\AA$/s for Cu. Deposition rate of Co showed a tendency of increasing of magnetoresistance ratio due to the formation of flat magnetic layer in case of high deposition rate of Co.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.3
• /
• pp.663-669
• /
• 2014

The electrical characteristics of RRAM with different annealing temperature and thickness have been measured and discussed. The devices with Pt/Ti top electrode of 150nm, Pt bottom electrode of 150nm, $HfO_2$ oxide thickness of 45nm and 70nm have been fabricated. The fabricated device were classified by 3 different kinds according to the annealing temperature, such as non-annealed, annealed at $500^{\circ}C$ and annealed at $850^{\circ}C$. The set and reset voltages and the variation of resistance with temperatures have been measured as electrical properties. From the measurement, it was found that the set voltages were decreased and the reset voltage were increased slightly, and thus the sensing window was decreased with increasing of measurement temperatures. It was remarkable that the device annealed at $850^{\circ}C$ showed the best performances. Although the device with thickness of 45nm showed better performances in the point of the sensing window, the resistance of 45nm devices was large relatively in the low resistive state. It can be expected to enhance the device performances with ultra thin RRAM if the defect generation could be reduced at the $HfO_2$ deposition process.

• Journal of the Korean Electrochemical Society
• /
• v.7 no.2
• /
• pp.94-99
• /
• 2004

Anode-supported flat tubular solid oxide fuel cell (SOFC) was investigated to increase the cell power density. The anode-supported flat tube was fabricated by extrusion process. The porosity and pore size of Ni/YSZ ($8mol\%$ yttria-stabilized zirconia) cermet anode were $50.6\%\;and\;0.23{\mu}m$, respectively. The Ni particles in the anode were distributed uniformly and connected well to each other particles in the cermet anode. YSZ electrolyte layer and multilayered cathode composed of $LSM(La_{0.85}Sr_{0.15})_{0.9}MnO_3)/YSZ$ composite, LSM, and $LSCF(La_{0.6}Sr_{0.4}Co_{0.2}Fe_{0.7}O_3)$ were coated onto the anode substrate by slurry dip coating, subsequently. The anode-supported flat tubular cell showed a performance of $300mW/cm^2 (0.6V,\; 500 mA/cm^2)\;at\;500^{\circ}C$. The electrochemical characteristics of the flat tubular cell were examined by ac impedance method and the humidified fuel enhanced the cell performance. Areal specific resistance of the LSM-coated SUS430 by slurry dipping process as metallic interconnect was $148m{\Omega}cm^2\;at\;750^{\circ}C$ and then decreased to $148m{\Omega}cm^2$ after 450hr. On the other hand, the LSM-coated Fecralloy by slurry dipping process showed a high area specific resistance.

• Composites Research
• /
• v.32 no.3
• /
• pp.148-157
• /
• 2019

In this study, $C_f/SiC$, $SiC_f/SiC$ and $C_f-SiC_f/SiC$ ceramic composites reinforcing carbon fiber, SiC fiber and hybrid fiber were fabricated by hybrid TGCVI and PIP process. After the thermal shock cycle, 3-point bending and Oxy-Acetylene torch test, their mechanical behavior, oxidation and erosion resistance were evaluated. The $C_f/SiC$ composite showed a decrease in mechanical property along with increasing temperature, a pseudo-ductile fracture mode and a large quantity of erosion. The $SiC_f/SiC$ composite exhibited stronger mechanical property and lower erosion rate compared to the $C_f/SiC$, but brittle fracture mode. On the other hand, hybrid type of $C_f-SiC_f/SiC$ composite gave the best mechanical property, more ductile failure mode than the $SiC_f/SiC$, and lower erosion rate than the $C_f/SiC$. During the Oxy-Acetylene torch test, the $SiO_2$ formed by reaction of the SiC matrix with oxygen prevented further oxidation or erosion of the fibers for $C_f-SiC_f/SiC$ and $SiC_f/SiC$ composites particularly. In conclusion, if a hybrid composite with low porosity is prepared, this material is expected to have high applicability as a high temperature thermo-structural composite under high temperature oxidation atmosphere by improving low mechanical property due to the oxidation of $C_f/SiC$ and brittle fracture mode of $SiC_f/SiC$ composite.