• Journal of the Korean Society for Railway
• /
• v.20 no.2
• /
• pp.190-195
• /
• 2017

This paper proposes a method to detect rail broken through impedance measurement. In general, broken rails are detected in real time using the track circuit, but the proposed method not only detects the broken rails but also estimates positions of broken areas by measuring the rail impedance. To electrically insulate one side of the rail, parallel resonance is made by adding a capacitor; then, the impedance of the other rail is measured. If the measured impedance has an inductive value, there is no broken area of rail. However if the measured impedance has a capacitive value, the rail is broken. The proposed method is modeled using a transmission line; it is shown that the modeling can estimate the position of the broken rail according to the impedance value. The rail impedance is measured by the proposed method for a 60m simple rail model, and it is verified that the presence of a broken rail changes the rail impedance.

• Journal of the Korean Society for Railway
• /
• v.11 no.3
• /
• pp.311-316
• /
• 2008

Ratcheting is a cyclic accumulation of strain under a cyclic loading. It is a kind of mechanisms which generate cracks in rail steels. Though some experimental and numerical study has been performed, modeling of ratcheting is still a challenging problem. In this study, an elastic-plastic constitutive equation with non-linear kinematic hardening equation was applied. Contact stresses in wheel-rail were analyzed. Under the tangential stress of the contact stresses, a cyclic stress-strain relation was obtained by using the model. A constant ratcheting strain per cycle was accumulated.

• Proceedings of the KSRS Conference
• /
• 2009.03a
• /
• pp.78-81
• /
• 2009

레일형 GB-SAR의 단점을 극복하고자 차량에 원형레일을 탑재하여 신속한 기동을 확보하고 합성구경의 길이를 늘리며 영상영역을 확장한 ArcSAR를 세계 최초로 설계하고 시작품을 제작하였다. ArcSAR의 핵심기술이라고 할 수 있는 원형레일은 알루미늄 프로파일로 제작한 회전디스크, 곡선가이드, 리니어 가이드로 구성되며, 서보모터를 이용하여 구동된다. 회전디스크의 지름은 2.1 m 이며, 회전 디스크 위에 장착된 곡선 가이드를 따라 안테나가 탑재된 리니어 가이드가 이동하며 정밀한 원형 운행을 하게 된다. 리니어 가이드는 슬라이드식으로 제작되어 최대 3 m 까지 확장이 가능하여 스폿 모드 측정시 6 m 길이의 레일에서의 자료 획득과 유사한 결과를 얻게 된다. SAR 측정 장비는 회전디스크 위에 장착되어 전원을 제외한 별도의 슬립링을 사용을 자제하였다. 레일의 구동과 자료의 획득은 LabVIEW 기반의 통합 제어측정 소프트웨어를 통해 구현하였으며, 실내 실험 및 현장적용 실험을 통해 가능성을 확인하였다.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.6 no.5
• /
• pp.59-66
• /
• 2002

Long-rails in railways and high-speed railway are subjected to additional stresses resulted from the displacements inconsistence between upper structures, and this phenomenon is more remarkable in continuous bridges than in simple bridges. For the sake of safety, railways have to guarantee trains to stop safely without derailment even in the event of earthquake. The influences of acceleration, braking, and temperature were analyzed by static nonlinear method. But earthquake loads that require dynamic nonlinear analysis are not considered in these methods. Because linear relation between relative displacements of decks and rail stresses is not guaranteed at the nonlinear systems such as long rails on the bridges, it is required compute to rail stresses considering both braking and earthquake load by nonlinear dynamic analysis method. In this study, dynamic analysis method with material non-linearity for rails on continuous bridges according to the Taiwan High Speed Railway(THSR) Design Specification volume 9 was developed. And additional stresses and displacements of long rails for acceleration, braking, and earthquake loads were analyzed by this method.

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.72-79
• /
• 2010

The significant of continuous welded rail (CWR) management is growing because KORAIL has the plan to convert the whole of conventional railway lines into CWRs through continuous activities since constructed the CWR track with 1.8km in Gyeongbu line in 1966. The CWR recently is needed a efficient management method because it is difficult to manage the CWR by the poor of technic and equipment, limited maintain labor force and shorted the maintain work time of CWR caused by industrialization, greenhouse effect and global warming In this point, The 70ton Tenser's which is using in the rail site has been analysised with no extra tenser's capacity in case of the under low temperature and exceed the length of 1km as a result of reviewing the CWR-related rules and standards, a series of records of safety accidents, operation obstacles, and the situation of broken rails published by KORAIL, existing rail temperature measurements, and CWR researches. Therefore avoid the excessive plan of the first set-up section, choice the proper time in the normal temperature that is possible to weld the rail, turning the difference of rail temperature and Installation temperature down is desirable.

• The Journal of the Convergence on Culture Technology
• /
• v.4 no.3
• /
• pp.213-220
• /
• 2018

The objective of this study was to estimate the optimum spacing of rail joint for a personal rapid transit(PRT) track system, and to compare the results with the normal rail and rail joint by performing the finite element analysis(FEA) and field measurements using actual vehicles. Based on the FEA and field measurement results compared, the optimum spacing of the rail joints was calculated to be maximum of 1.20m based on the rail displacement. The vertical displacement of the normal rail was higher than that of the rail joint at a spacing of 1.0m, but it was considered that the vehicle riding performance and serviceability of track would be improved in terms of the stability of the train due to similar to rail defection between normal rail and rail joint. Also, because of the proposed rail joint spacing in this study was longer than the current rail joint spacing, the economic effect would be expected by decreasing the amount of sleepers.

• Journal of the Korean Society for Railway
• /
• v.11 no.3
• /
• pp.317-325
• /
• 2008

As a result of recent research, it is reported that the periodic replacements criterion of rails is able to extend as grinding rail surface and using the continuous welded rail (CWR). This study evaluated correlation between conditions of track and load capacity of rail by analysing the dynamic response of track while the metro train is running. Also, it was converted the measured stress waveform into stress frequency histogram by the rain-flow counting methods, and then accumulated fatigue damage ratio and remaining service life of laid rail were calculated so as the apply the equivalence of stress to S-N curve of a new welded rail. Finally, this study suggests a revision of the periodic replacements criterion of CWR, which was based on accumulated passing tonnage, classified by the types and conditions of track system.

• Journal of the Korea Society for Simulation
• /
• v.30 no.1
• /
• pp.127-137
• /
• 2021

The method of utilizing the strain and vibration values of rails is primarily used to diagnose the condition of wheels and railroad facilities. The dynamic load is measured under the assumption that the strain of the rail and the load of the railroad vehicle are proportional. Wheel condition is measured under the assumption that the magnitude of the defect and the magnitude of the rail vibration are proportional. However, environmental factors affecting the strain and vibration of the rail such as vehicle speed, wheel load, climate, and track conditions are not reflected, many errors occur depending on the measurement conditions. In this study, the effect of track distortion, which is a major indicator of the track condition among the environmental factors that affect the strain and vibration of the rail, on the strain and vibration of the rail, was examined through dynamic simulation. As a measure to reduce the measurement deviation, the effect of securing additional measurement points was analyzed.

• The Journal of the Convergence on Culture Technology
• /
• v.10 no.2
• /
• pp.511-516
• /
• 2024

The recently enacted detailed guidelines on the performance evaluation of track facilities presented the necessary requirements regarding the evaluation procedures and implementation methods of track performance evaluation. However, the grade of rail surface damage is determined by external inspection (visual inspection), and there is no choice but to rely only on qualitative evaluation based on the subjective judgment of the inspector. Therefore, in this study, we attempted to develop a diagnostic application that can diagnose rail internal defects using rail surface damage. In the field investigation, rail surface damage was investigated and patterns were analyzed. Additionally, in the indoor test, SEM testing was used to construct image data of rail internal damage, and crack length, depth, and angle were quantified. In this study, a deep learning model (Fast R-CNN) using image data constructed from field surveys and indoor tests was applied to the application. A rail surface damage diagnosis application (App) using a deep learning model that can be used on smart devices was developed. We developed a smart diagnosis system for rail surface damage that can be used in future track diagnosis and performance evaluation work.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.13 no.3
• /
• pp.29-38
• /
• 2009

n the event of an earthquake, additional stresses can occur in the continuous welded rails (CWR) of High-speed railway (HSR) bridges due to relative displacements at expansion joints, and this stress can cause derailment. The amplification of ground motion occurs as a result of site effects, and this is pronounced at the site of a soft surface soil layer and of a rigid surface soil layer over a soft one. As a result, the amplified ground motion leads to an amplified seismic response in HSR bridges. A change in bridge pier height affects the seismic behavior of the bridge. A HSR bridge with gravel ballast tracks will show different dynamic behavior during an earthquake than one with concrete ballast tracks. The seismic responses of HSR bridges and their CWR are analyzed considering the derailment-inducing factors.